auto trans removal - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

briancamaross · 06-26-2015, 12:03 PM

I cant find the link to remove my auto trans to do my stall next weekend any one can send me the link thanks

etmx183 · 06-26-2015, 12:42 PM

Transmission Replacement

Note:
NEW cooler pipe O-rings and torque converter bolts will be required each time the transmission is removed and installed.

Removal Procedure

1. Remove the exhaust system. Refer to Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (L99,LS3,LFX) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe ReplacementExhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (LSA) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement.

2. Remove the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Left Side (V8)Catalytic Converter Replacement - Left Side (LFX) and Catalytic Converter Replacement - Right Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Right Side (V8)Catalytic Converter Replacement - Right Side (LFX) .

3. Remove the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement (195/218mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (195/218mm Axle)Two-Piece Propeller Shaft Replacement (250mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (250mm Axle).

4. Disconnect the shift linkage from the transmission.

Zoom and Print Options

5. Remove the transmission vent hose from the retaining clips (6) on the transmission support.

Zoom and Print Options

6. Disconnect the transmission wiring harness connector (4) from the transmission by releasing the locking mechanism and rotating the latch counterclockwise.

7. Remove the wiring harness retainers (1) from the transmission.

8. Remove the oxygen sensor wiring harness connector (2) from the transmission.

9. Place an oil drain pan under the transmission fluid cooler pipes.

Zoom and Print Options

10. Remove the transmission fluid cooler pipes (1) from the transmission, and position aside.

11. Remove and discard the O-rings. Do NOT reuse the O-rings.

12. Plug the open outlet ports to prevent fluid loss and contamination.

Zoom and Print Options

13. Remove the transmission close out plug (1).

14. Mark the torque converter to flexplate/flywheel orientation to ensure proper realignment.

15. Remove the starter motor. Refer to Starter Replacement (LFX) See: Starter Motor > Removal and Replacement > Starter ReplacementStarter Replacement (LSA,LS3,L99) See: Starter Motor > Removal and Replacement > Starter Replacement.

16. Remove the right side transmission torque converter cover.

Zoom and Print Options

17. Repeat the following steps for all torque converter bolts (1):

1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt with the access hole.

2. Remove and discard the torque converter bolts.

18. Support the transmission with a suitable transmission jack.

19. Remove the transmission support. Refer to Transmission Mount Replacement See: Transmission Mount, A/T > Removal and Replacement > Transmission Mount Replacement.

20. Slightly lower the transmission to gain access to the upper transmission retaining bolts.

Zoom and Print Options

21. Disconnect the transmission vent hose (4) from the transmission vent pipe (1).

Zoom and Print Options

22. Remove the wiring harness retainers (2) from the transmission.

23. Position the transmission wiring harness (1) and vent tube out of the way.

24. On V6 models, remove the heater inlet and outlet pipe to access the top transmission bolt. Refer to Heater Inlet And Outlet Pipe Replacement (LFX) .

Zoom and Print Options

25. Remove the transmission mounting bolts (1-6).

26. Remove the remaining two transmission bolts from the transmission.

27. Pull the transmission free from the engine dowels.

Note:
Ensure clearance is maintained between the transmission and the following:

* The wiring harness

* The vent tube

* The cooler pipes

28. Carefully lower the transmission from the vehicle.

29. Flush and flow test the transmission oil cooler and lines. Refer to Transmission Fluid Cooler Flushing and Flow Test See: Fluid - A/T > Component Tests and General Diagnostics > Transmission Fluid Cooler Flushing and Flow Test.

Installation Procedure

Note:
Ensure clearance is maintained between the transmission and the following:

* The wiring harness

* The vent tube

* The cooler pipes

1. Using the transmission jack, carefully raise the transmission to the engine.

Zoom and Print Options

2. Align the transmission with the engine dowels.

Caution:
Refer to Fastener Caution See: Vehicle > Technician Safety Information > Fastener Caution.

3. Install the transmission mounting bolts and tighten to 50 Nm (37 lb ft).

Zoom and Print Options

4. Position the engine wiring harness (1) to the original location.

5. Install the wiring harness retainers (2) to the transmission.

Zoom and Print Options

6. Connect the transmission vent hose (4) to the transmission vent pipe (1).

7. Raise the transmission to the installed position.

8. Install the transmission support. Refer to Transmission Mount Replacement See: Transmission Mount, A/T > Removal and Replacement > Transmission Mount Replacement.

9. Remove the jack from under the transmission.

10. Align the torque converter to flexplate/flywheel orientation marks made during the removal procedure.

Zoom and Print Options

Note:
Torque converter bolts are self locking and must be replaced with NEW torque converter bolts every time the bolts are removed.

11. Complete the following steps for all torque converter bolts (1):

1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt holes in the flexplate/flywheel with the access hole in the engine block.

2. To aid in alignment of the torque converter to the flexplate/flywheel. Install all NEW torque converter bolts before fully tightening to 65 Nm (48 lb ft).

12. Install the starter motor. Refer to Starter Replacement (LFX) See: Starter Motor > Removal and Replacement > Starter ReplacementStarter Replacement (LSA,LS3,L99) See: Starter Motor > Removal and Replacement > Starter Replacement.

13. Install the right side transmission torque converter cover.

Zoom and Print Options

14. Install the transmission close out plug (1).

Zoom and Print Options

15. Place NEW O-rings over the transmission fluid cooler pipes.

16. Install the transmission fluid cooler pipes (1) to the transmission.

Zoom and Print Options

17. Install the oxygen sensor wiring harness connector (2) to the transmission.

18. Install the wiring harness retainers (1) to the transmission.

19. Connect the transmission wiring harness connector (5) to the transmission by rotating the locking latch clockwise.

Zoom and Print Options

20. Install the transmission vent hose to the retaining clips (6) on the transmission support.

21. On V6 models, install the heater inlet and outlet pipe. Refer to Heater Inlet And Outlet Pipe Replacement (LFX) .

Zoom and Print Options

22. Install the shift linkage fastener (1) to the transmission. Refer to Shift Control Linkage Replacement See: Shift Linkage, A/T > Removal and Replacement > Shift Control Linkage Replacement.

23. Install the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement (195/218mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (195/218mm Axle)Two-Piece Propeller Shaft Replacement (250mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (250mm Axle).

24. Install the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Left Side (V8)Catalytic Converter Replacement - Left Side (LFX) and Catalytic Converter Replacement - Right Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Right Side (V8)Catalytic Converter Replacement - Right Side (LFX) .

25. Install the exhaust system. Refer to Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (L99,LS3,LFX) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe ReplacementExhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (LSA) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement.

26. Lower the vehicle.

27. Check the transmission fluid level and fill if necessary.

28. Adjust the shift control linkage. Refer to Shift Control Linkage Adjustment See: Shift Linkage, A/T > Adjustments > Shift Control Linkage Adjustment.

Transmission Final Test and Inspection

Complete the following procedure after the transmission is installed in the vehicle:

1. With the ignition OFF or disconnected, crank the engine several times. Listen for any unusual noises or evidence that any parts are binding.

2. Start the engine and listen for abnormal conditions.

3. While the engine continues to idle, raise and support the vehicle.

4. Inspect for fluid leaks while the engine is idling.

5. Perform a final inspection for the proper fluid level.

6. Lower the vehicle.

7. If a NEW TCM has been installed into the vehicle, the NEW module needs to be reprogrammed. Refer to Service Programming System (SPS) See: Vehicle > Programming and Relearning > Service Programming System (SPS).

Note:
The Service Fast Learn Adapts procedure must be performed when one of the following repairs have been made to the vehicle. Failure to perform the procedure after one of the following repairs may result in poor transmission performance, as well as transmission DTCs being set:

* Transmission internal service/overhaul

* Valve body repair or replacement

* Control solenoid valve assembly replacement

* TCM software/calibration update

* Any service in response to a shift quality concern

8. Perform the Reset Transmission Adapts. Refer to Reset Transmission Adapts See: Automatic Transmission/Transaxle > Reset Procedure > Reset Procedure.

9. Road test the vehicle. Refer to Road Test See: Automatic Transmission/Transaxle > Initial Inspection and Diagnostic Overview > Road Test.

06-26-2015, 12:03 PM	#1
briancamaross Drives: 2011 ss 2ss auto camaro Join Date: Mar 2015 Location: mary esther florida Posts: 385 View My Garage	auto trans removal I cant find the link to remove my auto trans to do my stall next weekend any one can send me the link thanks

06-26-2015, 12:42 PM	#2
etmx183 Drives: 2012 Camaro 2LT RS Join Date: Mar 2012 Location: Baltimore, Maryland Posts: 1,633 View My Garage	Transmission Replacement Note: NEW cooler pipe O-rings and torque converter bolts will be required each time the transmission is removed and installed. Removal Procedure 1. Remove the exhaust system. Refer to Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (L99,LS3,LFX) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe ReplacementExhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (LSA) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement. 2. Remove the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Left Side (V8)Catalytic Converter Replacement - Left Side (LFX) and Catalytic Converter Replacement - Right Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Right Side (V8)Catalytic Converter Replacement - Right Side (LFX) . 3. Remove the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement (195/218mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (195/218mm Axle)Two-Piece Propeller Shaft Replacement (250mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (250mm Axle). 4. Disconnect the shift linkage from the transmission. Zoom and Print Options 5. Remove the transmission vent hose from the retaining clips (6) on the transmission support. Zoom and Print Options 6. Disconnect the transmission wiring harness connector (4) from the transmission by releasing the locking mechanism and rotating the latch counterclockwise. 7. Remove the wiring harness retainers (1) from the transmission. 8. Remove the oxygen sensor wiring harness connector (2) from the transmission. 9. Place an oil drain pan under the transmission fluid cooler pipes. Zoom and Print Options 10. Remove the transmission fluid cooler pipes (1) from the transmission, and position aside. 11. Remove and discard the O-rings. Do NOT reuse the O-rings. 12. Plug the open outlet ports to prevent fluid loss and contamination. Zoom and Print Options 13. Remove the transmission close out plug (1). 14. Mark the torque converter to flexplate/flywheel orientation to ensure proper realignment. 15. Remove the starter motor. Refer to Starter Replacement (LFX) See: Starter Motor > Removal and Replacement > Starter ReplacementStarter Replacement (LSA,LS3,L99) See: Starter Motor > Removal and Replacement > Starter Replacement. 16. Remove the right side transmission torque converter cover. Zoom and Print Options 17. Repeat the following steps for all torque converter bolts (1): 1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt with the access hole. 2. Remove and discard the torque converter bolts. 18. Support the transmission with a suitable transmission jack. 19. Remove the transmission support. Refer to Transmission Mount Replacement See: Transmission Mount, A/T > Removal and Replacement > Transmission Mount Replacement. 20. Slightly lower the transmission to gain access to the upper transmission retaining bolts. Zoom and Print Options 21. Disconnect the transmission vent hose (4) from the transmission vent pipe (1). Zoom and Print Options 22. Remove the wiring harness retainers (2) from the transmission. 23. Position the transmission wiring harness (1) and vent tube out of the way. 24. On V6 models, remove the heater inlet and outlet pipe to access the top transmission bolt. Refer to Heater Inlet And Outlet Pipe Replacement (LFX) . Zoom and Print Options 25. Remove the transmission mounting bolts (1-6). 26. Remove the remaining two transmission bolts from the transmission. 27. Pull the transmission free from the engine dowels. Note: Ensure clearance is maintained between the transmission and the following: * The wiring harness * The vent tube * The cooler pipes 28. Carefully lower the transmission from the vehicle. 29. Flush and flow test the transmission oil cooler and lines. Refer to Transmission Fluid Cooler Flushing and Flow Test See: Fluid - A/T > Component Tests and General Diagnostics > Transmission Fluid Cooler Flushing and Flow Test. Installation Procedure Note: Ensure clearance is maintained between the transmission and the following: * The wiring harness * The vent tube * The cooler pipes 1. Using the transmission jack, carefully raise the transmission to the engine. Zoom and Print Options 2. Align the transmission with the engine dowels. Caution: Refer to Fastener Caution See: Vehicle > Technician Safety Information > Fastener Caution. 3. Install the transmission mounting bolts and tighten to 50 Nm (37 lb ft). Zoom and Print Options 4. Position the engine wiring harness (1) to the original location. 5. Install the wiring harness retainers (2) to the transmission. Zoom and Print Options 6. Connect the transmission vent hose (4) to the transmission vent pipe (1). 7. Raise the transmission to the installed position. 8. Install the transmission support. Refer to Transmission Mount Replacement See: Transmission Mount, A/T > Removal and Replacement > Transmission Mount Replacement. 9. Remove the jack from under the transmission. 10. Align the torque converter to flexplate/flywheel orientation marks made during the removal procedure. Zoom and Print Options Note: Torque converter bolts are self locking and must be replaced with NEW torque converter bolts every time the bolts are removed. 11. Complete the following steps for all torque converter bolts (1): 1. Rotate the harmonic balancer center bolt clockwise ONLY, in order to align the torque converter bolt holes in the flexplate/flywheel with the access hole in the engine block. 2. To aid in alignment of the torque converter to the flexplate/flywheel. Install all NEW torque converter bolts before fully tightening to 65 Nm (48 lb ft). 12. Install the starter motor. Refer to Starter Replacement (LFX) See: Starter Motor > Removal and Replacement > Starter ReplacementStarter Replacement (LSA,LS3,L99) See: Starter Motor > Removal and Replacement > Starter Replacement. 13. Install the right side transmission torque converter cover. Zoom and Print Options 14. Install the transmission close out plug (1). Zoom and Print Options 15. Place NEW O-rings over the transmission fluid cooler pipes. 16. Install the transmission fluid cooler pipes (1) to the transmission. Zoom and Print Options 17. Install the oxygen sensor wiring harness connector (2) to the transmission. 18. Install the wiring harness retainers (1) to the transmission. 19. Connect the transmission wiring harness connector (5) to the transmission by rotating the locking latch clockwise. Zoom and Print Options 20. Install the transmission vent hose to the retaining clips (6) on the transmission support. 21. On V6 models, install the heater inlet and outlet pipe. Refer to Heater Inlet And Outlet Pipe Replacement (LFX) . Zoom and Print Options 22. Install the shift linkage fastener (1) to the transmission. Refer to Shift Control Linkage Replacement See: Shift Linkage, A/T > Removal and Replacement > Shift Control Linkage Replacement. 23. Install the propeller shaft. Refer to Two-Piece Propeller Shaft Replacement (195/218mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (195/218mm Axle)Two-Piece Propeller Shaft Replacement (250mm Axle) See: Drive/Propeller Shaft > Removal and Replacement > Two-Piece Propeller Shaft Replacement (250mm Axle). 24. Install the catalytic converters. Refer to Catalytic Converter Replacement - Left Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Left Side (V8)Catalytic Converter Replacement - Left Side (LFX) and Catalytic Converter Replacement - Right Side (V8) See: Catalytic Converter > Removal and Replacement > Catalytic Converter Replacement - Right Side (V8)Catalytic Converter Replacement - Right Side (LFX) . 25. Install the exhaust system. Refer to Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (L99,LS3,LFX) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe ReplacementExhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement (LSA) See: Muffler > Removal and Replacement > Exhaust Muffler with Resonator, Exhaust, and Tail Pipe Replacement. 26. Lower the vehicle. 27. Check the transmission fluid level and fill if necessary. 28. Adjust the shift control linkage. Refer to Shift Control Linkage Adjustment See: Shift Linkage, A/T > Adjustments > Shift Control Linkage Adjustment. Transmission Final Test and Inspection Complete the following procedure after the transmission is installed in the vehicle: 1. With the ignition OFF or disconnected, crank the engine several times. Listen for any unusual noises or evidence that any parts are binding. 2. Start the engine and listen for abnormal conditions. 3. While the engine continues to idle, raise and support the vehicle. 4. Inspect for fluid leaks while the engine is idling. 5. Perform a final inspection for the proper fluid level. 6. Lower the vehicle. 7. If a NEW TCM has been installed into the vehicle, the NEW module needs to be reprogrammed. Refer to Service Programming System (SPS) See: Vehicle > Programming and Relearning > Service Programming System (SPS). Note: The Service Fast Learn Adapts procedure must be performed when one of the following repairs have been made to the vehicle. Failure to perform the procedure after one of the following repairs may result in poor transmission performance, as well as transmission DTCs being set: * Transmission internal service/overhaul * Valve body repair or replacement * Control solenoid valve assembly replacement * TCM software/calibration update * Any service in response to a shift quality concern 8. Perform the Reset Transmission Adapts. Refer to Reset Transmission Adapts See: Automatic Transmission/Transaxle > Reset Procedure > Reset Procedure. 9. Road test the vehicle. Refer to Road Test See: Automatic Transmission/Transaxle > Initial Inspection and Diagnostic Overview > Road Test.