05-27-2014, 12:02 PM | #1 |
Chu no guat a hasa is?
Drives: 14 Jeep G Cherokee Overland HEMI Join Date: Jun 2011
Location: Some where in So Cal
Posts: 4,273
|
Husky Liners Mud Flaps/Guards
I installed my rear husky liner flaps. They look great. I thought they were much bigger but im glad they are not. Didnt install fronts as i was racing with day light. Rears were a bit of a pita without removing the tires but luckily i had the right tools handy.
Planning on installing fronts maybe this weekend.
__________________
11 2SS/RSL99No Longer Stock (Sold) 6/19/14:AAC Plasma DRL's | Plug n play harness | Elite CC | Tint: 35% & 5% | LED Dome light | Show-N-Go Plate Holder | Flowmaster AT | C.A.I. Intake | VMAX CNC Spiral Ported TB | Husky Splash Guards
|
06-09-2014, 03:31 PM | #2 |
|
Those look great Gunner... just like mine. I just finished RE-installing my front Husky guards. As we discussed, the front ones stick out too far using the factory drilled holes (See below). Didn't like that look at all.
So I took them off and drilled new holes 9/16" towards the outer edge of the guard (See below). Holes are hard to see because I used a much smaller drill bit, but they're there). Then I got some black painted sheet metal screws to replace the two washered screws that came with the guards (couldn't get the washers off), for the screws that go in the metal fender itself. Reused the lower two torque-heads that go into the plastic inner fender. And... Ta Daaaaa! I think they look MUCH better and plan to keep them. It took me about 20 minutes to do each side. I measured and drilled carefully. Have you tackled yours yet?
__________________
2013 1SS/RS Coupe L99, Stainless Power Works LT Headers, SCT X4 Custom Tune from RDP, CAI Inc. Air Intake w/ Apex Scoop, VMAX CNC Ported Throttle Body, Solo Axle-Back Exhaust w/ J-pipes, Apex Catch Can, Husky Splash Guards, Heritage Grille, 3D Carbon Rear Spoiler, Oracle Chrome Turn Signal Bulbs, GM Reverse Light Trim Billets, Gorilla Black Locking Lugs, Emblem Pros Retro SS Badges/Custom Retro SS Kickplates/Under-hood Bowtie, 35% window Tint, Nitto Motivo Tires (6-8-18)
|
06-09-2014, 03:45 PM | #3 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
Where did you get those?
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
06-09-2014, 03:52 PM | #4 |
|
__________________
2013 1SS/RS Coupe L99, Stainless Power Works LT Headers, SCT X4 Custom Tune from RDP, CAI Inc. Air Intake w/ Apex Scoop, VMAX CNC Ported Throttle Body, Solo Axle-Back Exhaust w/ J-pipes, Apex Catch Can, Husky Splash Guards, Heritage Grille, 3D Carbon Rear Spoiler, Oracle Chrome Turn Signal Bulbs, GM Reverse Light Trim Billets, Gorilla Black Locking Lugs, Emblem Pros Retro SS Badges/Custom Retro SS Kickplates/Under-hood Bowtie, 35% window Tint, Nitto Motivo Tires (6-8-18)
|
06-09-2014, 04:02 PM | #5 |
Chu no guat a hasa is?
Drives: 14 Jeep G Cherokee Overland HEMI Join Date: Jun 2011
Location: Some where in So Cal
Posts: 4,273
|
Wow. Big difference. They look great. Thanks for sharing. I still haven't gotten around to doing the fronts yet. May do them this weekend. I hope.
__________________
11 2SS/RSL99No Longer Stock (Sold) 6/19/14:AAC Plasma DRL's | Plug n play harness | Elite CC | Tint: 35% & 5% | LED Dome light | Show-N-Go Plate Holder | Flowmaster AT | C.A.I. Intake | VMAX CNC Spiral Ported TB | Husky Splash Guards
|
06-20-2014, 08:33 AM | #6 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
Got my set in the mail last night, will probably install them this weekend. I think I will go with the 9/16" offset like shown above, I like that look. Overall I was really impressed on how they look and how they match up with the other textured plastic on these cars (sideskirts, diffuser, etc).
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
06-23-2014, 07:38 AM | #7 |
Drives: 2012 1LT Drop Top Join Date: Oct 2013
Location: Yardley, Pa
Posts: 745
|
Cheaper on Amazon vs Husky.com. ($85 + free shipping instead of $91 + shipping)!
__________________
|
06-23-2014, 09:46 AM | #8 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
Installed:
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
06-23-2014, 09:47 AM | #9 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
I got mine via a father's day sale on the Husky website for $82 shipped.
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
07-22-2014, 11:43 AM | #10 |
synergy2011
|
How do the inside look with the new holes and old holes what did install do to hide the holes on front
__________________
2011 synergy green ss/rs,rally stripes
|
07-22-2014, 12:56 PM | #11 |
2010 2SS/RS M6
Drives: 2010 2SS/RS M6 Join Date: Jun 2010
Location: Auckland, NZ
Posts: 1,482
|
Im assuming you're referring to the Original holes on the fronts when we "shifted" it? If so, I didn't do anything with them. It's the inside of a wheel well, it's supposed to get beatup.
__________________
2/7/2014: 419 hp, 419 tq
Cosmetic: ZL1 front w/mailslot, painted stripes, powdercoated SS rims, tow hook, and full chrome delete Suspension: Pfadt subframe bushings, Pfadt rear UCA bushings, Z28 Upper control arms, Spohn trailing arms with BMR trailing arm & differential bushings, ZL1 Toe Rods and springs, Prothane radius arm inserts & steering rack bushing, Pfadt Sport front sway, FE4 conversion w/ DS rear sway, Pfadt strut brace Drivetrain: RMCR tune, CAI intake, Kooks headers, hi-flo cats & exhaust, VMAX TB, ZL1 fuel pump, LSR Tri-Ax shifter Bumblebee Racecar Build |
07-22-2014, 01:02 PM | #12 |
Drives: 2014 Camaro SS Join Date: Jul 2014
Location: dover pa
Posts: 248
|
Is that $85 price for all 4? I was going to get the 1LE/ZL1 style flaps....but not for double the price of the husky version...tbey look great....good to know about the screw hole spacing....def will order these soon!!
__________________
2014 Ashen Gray Metallic 2SS/RS M6
CAGS Skip-Shift Eliminator 1LE Strut Tower Brace GMPP Track Pack Axleback Halltech CAI Fuse Pull Mod |
07-22-2014, 01:10 PM | #13 |
Yes, that's for all 4.
__________________
2010 Summit White 2SS/RS M6: Injen longtube cold air intake, Borla S-Type cat-back exhaust, Tint, White painted rear diffuser, Red powder-coated Brembo calipers, New Era Performance ported throttle body, BMR 1" lowering springs, Hotchkis Chassis Max Strut Tower Brace, Red hash stripes, Vossen Matte Graphite/Machined CV5's
|
|
07-22-2014, 02:05 PM | #14 |
Drives: 2014 Camaro SS Join Date: Jul 2014
Location: dover pa
Posts: 248
|
Nice.
__________________
2014 Ashen Gray Metallic 2SS/RS M6
CAGS Skip-Shift Eliminator 1LE Strut Tower Brace GMPP Track Pack Axleback Halltech CAI Fuse Pull Mod |
|
|
|
|