06-04-2010, 06:38 AM | #1 |
Drives: IOM 2SS/RS Join Date: Oct 2009
Location: Knoxville, TN
Posts: 7
|
Problems from cutouts
I installed the QTP oval cutouts on my car a couple of months ago and now am having big problems. To start this whole thing off, earlier this week I had my car in competitive mode, dropped the clutch, and it is still at the dealer waiting for the broken axle to be shipped in and fixed. I got a call from my dealer the next day after they started looking at it telling me I needed to come look at my car. He said that they looked at my cutouts and that my car was “extremely dangerous” from those cutouts. I figured that it probably wasn’t something to worry too much about, and he was exaggerating it a bit since they was a modification to the car. It turned out that it was actually a big deal like they said. My driver’s side cutout was causing the floorboard under the back seat to start being discolored from all the heat thrown on it. The tech said that over time with this heating and cooling process that it would start to rust, which makes sense. But the bad part was the problems on the right side. The way this cutout was designed was blowing the exhaust back towards the 4 brake and fuel lines. It has actually melted one of the plastic clamps that mounts those lines to the floorboard, so they were barely attached. If those lines became too hot and melted, it would either be no brakes in the rear, or an explosion from hot exhaust and leaking gas…
I had an exhaust shop weld these cutouts on, and we followed the directions just like they said. And I have the 2 turndowns that go over the butterfly valves, too. I know that they’ve been put on the right way, so that’s why I don’t understand why there’s these problems. This has made me wonder why no one else has had these problems. Or do other people have them too, and don’t know it yet? Needless to say I won’t have those open until this thing can be fixed or taken off. Does anyone have any suggestions to fix this?
__________________
LS3 2SS/RS IOM
Black Rally Stipes, Trunk Blackout Stripe Check out my pictures: http://www.flickr.com/photos/tnwagn/...7623827964766/ |
06-04-2010, 07:34 AM | #2 |
|
Well that's not good!
__________________
Mods: BBK Intake, BBK LT's and High Flow Cats, Corsa Cat-back exhaust, Hurst short throw shifter, SLP skip-shift eliminator. 7/1/09 Placed order for IOM/IO int/ SS/RS 6M 9/26/09 Took delivery! |
06-04-2010, 07:42 AM | #3 |
Account Suspended
Drives: 2005 GTO, 1973 Camaro Join Date: Aug 2009
Location: Westchester
Posts: 460
|
Have you been driving around with open headers for a while. It wouldn't be something you should do often. Its meant for the track or if you just want to show off a bit.
|
06-05-2010, 02:24 PM | #4 |
Drives: IOM 2SS/RS Join Date: Oct 2009
Location: Knoxville, TN
Posts: 7
|
I do drive around with them open pretty often, but that's the whole reason I bought them was to use them.
__________________
LS3 2SS/RS IOM
Black Rally Stipes, Trunk Blackout Stripe Check out my pictures: http://www.flickr.com/photos/tnwagn/...7623827964766/ |
06-05-2010, 02:33 PM | #5 |
BAMF SS
|
if you want something that loud 24/7, then just sell the cut outs and go out and get a muffler delete kit or a slp loudmouth 1 exhaust
__________________
2016 1SS A8: FBO + Circle D + P1X + Meth + Tuned by Pray Performance
Stock Longblock 800 SAE rwhp. 9.4 @ 145 mph. |
06-05-2010, 02:35 PM | #6 |
Drives: red ss Join Date: Mar 2010
Location: orange county
Posts: 12
|
cut outs are always a problem, especially on a daily driver...next they will get stuck and not close or just leak...imo
Ditch the cut outs |
06-05-2010, 02:43 PM | #7 |
Drives: 2SS/RS Join Date: May 2009
Location: Texas
Posts: 586
|
|
06-05-2010, 02:46 PM | #8 |
Drives: Trailblazer SS & Camaro SS Join Date: Nov 2009
Location: North Jersey
Posts: 758
|
I have QTP cutouts also, Had them on for maybe 3-4 months now and drive around with them open 99% of the time. Now your making me think twice about keeping them...
Wonder what QTP has to say about this?
__________________
2010 Camaro 2SS/RS/LS3 -Black on Black - Kooks 1-7/8 Headers, Dyno Tuned, ADM Race CAI, QTP Cutouts, Hurst Short Throw, SJM Line Lock, Alpine PDX 1.1000, (2) Alpine Type R's, ...Soon to be cammed!
|
06-05-2010, 02:57 PM | #9 | |
BAMF SS
|
Quote:
mine is! or as said before.... go with a slp lm1, which imo is even louder than cutouts
__________________
2016 1SS A8: FBO + Circle D + P1X + Meth + Tuned by Pray Performance
Stock Longblock 800 SAE rwhp. 9.4 @ 145 mph. |
|
|
|
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
1st and 2nd gear problems. 1SS 6M | jnm2003 | V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) | 7 | 10-29-2019 12:22 PM |
QTP Electric Exhaust Cutouts Pictures and Videos!!! | Quick Time | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 51 | 08-08-2015 09:09 PM |
MTI Racing DMH Exhaust Cutouts | MTI Racing Kevin | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 16 | 07-13-2012 06:23 AM |
MTI Racing DMH Exhaust Cutouts | MTI Racing | V8 Bolt-Ons & Tunes | 1 | 06-01-2010 10:25 AM |
Does an axle back have the same problems as a cat back? | G.E. | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 2 | 09-15-2009 03:31 PM |