Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Roto-Fab
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Forced Induction - V8


Reply
 
Thread Tools
Old 05-30-2010, 11:47 AM   #1
n2oSS
 
n2oSS's Avatar
 
Drives: 2010 SS2 Camaro
Join Date: Oct 2009
Location: Houston, TX
Posts: 434
maggie install, hose routing suggestions please

I installed my maggie last weekend and was having a problem routing the hoses off the heat exchanger (bottom of car) up to pump and sc.

I cut the hoses to length directions specified but i am having to run the hoses under the frame of the car so they don't crease or rub against sharp edges of plastic.

anyone got pics or suggestions how to run these effectivly above the frame?
__________________
Mods:
Dynatech Headers, High flow cats, MSD 8.5 wires, magnaflow bullits, Halltech intake, SCT tuner,
maggie tvs 2300, Jannetty Tune, BMR driveshaft safety loop, Pfadt drop springs, Pfadt rear trailing arms, Pfadt rear tie rod, ACT Twin Disc Clutch, DSS Aluminum Driveshaft.
Appearance Mods:
AAC Concept Sidemarkers, P13W Plasma LED Bulbs, Iforged Classics 20".
Next Mods:
Cam and Fuel System.
n2oSS is offline   Reply With Quote
Old 05-31-2010, 05:03 AM   #2
racingray68
racingray
 
racingray68's Avatar
 
Drives: 1968 camaro ss
Join Date: Mar 2009
Location: Johnstown Pa
Posts: 73
Quote:
Originally Posted by n2oSS View Post
I installed my maggie last weekend and was having a problem routing the hoses off the heat exchanger (bottom of car) up to pump and sc.

I cut the hoses to length directions specified but i am having to run the hoses under the frame of the car so they don't crease or rub against sharp edges of plastic.

anyone got pics or suggestions how to run these effectivly above the frame?
I ran mine just how the directions said and the bigger heater hose has a small crease in it. The hoses are not good quality and I will switch over the winter
racingray68 is offline   Reply With Quote
Old 05-31-2010, 08:46 AM   #3
n2oSS
 
n2oSS's Avatar
 
Drives: 2010 SS2 Camaro
Join Date: Oct 2009
Location: Houston, TX
Posts: 434
yeah thats the problem i keep running into, just aggrivating to buy new hoses for a new kit lol
__________________
Mods:
Dynatech Headers, High flow cats, MSD 8.5 wires, magnaflow bullits, Halltech intake, SCT tuner,
maggie tvs 2300, Jannetty Tune, BMR driveshaft safety loop, Pfadt drop springs, Pfadt rear trailing arms, Pfadt rear tie rod, ACT Twin Disc Clutch, DSS Aluminum Driveshaft.
Appearance Mods:
AAC Concept Sidemarkers, P13W Plasma LED Bulbs, Iforged Classics 20".
Next Mods:
Cam and Fuel System.
n2oSS is offline   Reply With Quote
Old 05-31-2010, 08:51 AM   #4
Camaro21


 
Drives: SOLD - 2013 M6 ZL1
Join Date: Jul 2009
Location: Texas
Posts: 5,041
ADM Performance offers a Heater Hose Relocation Kit that I have on my car and it is awesome.. Check out the following link..

http://admperformance.com/products.p...50&product=210
Camaro21 is offline   Reply With Quote
Old 05-31-2010, 10:11 AM   #5
racingray68
racingray
 
racingray68's Avatar
 
Drives: 1968 camaro ss
Join Date: Mar 2009
Location: Johnstown Pa
Posts: 73
Quote:
Originally Posted by Camaro21 View Post
ADM Performance offers a Heater Hose Relocation Kit that I have on my car and it is awesome.. Check out the following link..

http://admperformance.com/products.p...50&product=210
I haven't seen that kit in person, but I did look at it online looks good but its pricey.
racingray68 is offline   Reply With Quote
Old 05-31-2010, 10:22 AM   #6
n2oSS
 
n2oSS's Avatar
 
Drives: 2010 SS2 Camaro
Join Date: Oct 2009
Location: Houston, TX
Posts: 434
wonder if they'd just sell the hoses i need, don't really want the little ones, those hoses are fine.
__________________
Mods:
Dynatech Headers, High flow cats, MSD 8.5 wires, magnaflow bullits, Halltech intake, SCT tuner,
maggie tvs 2300, Jannetty Tune, BMR driveshaft safety loop, Pfadt drop springs, Pfadt rear trailing arms, Pfadt rear tie rod, ACT Twin Disc Clutch, DSS Aluminum Driveshaft.
Appearance Mods:
AAC Concept Sidemarkers, P13W Plasma LED Bulbs, Iforged Classics 20".
Next Mods:
Cam and Fuel System.
n2oSS is offline   Reply With Quote
Old 05-31-2010, 03:59 PM   #7
Camaro21


 
Drives: SOLD - 2013 M6 ZL1
Join Date: Jul 2009
Location: Texas
Posts: 5,041
Call Andy and ask him.. I think it was well worth the money!! I just dropped off my car at ADM Performance this afternoon to get a Cam, Fuel Boost-a-Pump, Blower Pulley and 3.70 Rear End Gears...
Camaro21 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY : Install headers on 2010 Camaro SS Nine Ball Camaro DIY & HOW-TO instructions & discussions 70 06-25-2020 06:40 PM
DIY : Install underdrive pulley on 2010 Camaro SS Nine Ball Camaro DIY & HOW-TO instructions & discussions 34 09-30-2013 08:25 PM
Spoiler install hose my stripes? lostinvt Cosmetics and Lighting Modification Discussions 12 08-24-2009 02:13 PM
DIY : Install catback on 2010 Camaro SS Nine Ball Camaro DIY & HOW-TO instructions & discussions 3 08-09-2009 04:36 PM


All times are GMT -5. The time now is 03:52 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.