06-20-2013, 10:35 AM | #659 |
Drives: 2011 cyber grey metallic camaro v6 Join Date: Jun 2011
Location: hampton va
Posts: 219
|
Hey gretchen wanna race when I get my rods and bolts and try and get into gm high tech performance magazine ;-) I've emailed them already and they seem interested
__________________
2011 camaro v6- sts turbo w/ meth injection, barton short throw, spec stage 3+ clutch, forgestar f-14 rims, Nitto invo tires, pfadt sway bars drop springs and end links, rx catch can, goodridge stainless steel brake lines, aac halos afterburner taillights and sidemarkers, sebon carbon rear diffuser.
|
06-20-2013, 10:38 AM | #660 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
Sure. Not sure everything will be ready for CamaroFest, but if it is then that might be a good place.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread |
06-20-2013, 10:40 AM | #661 |
COTW 5/06/2013
Drives: 2017 Corvette Grand Sport-Ho-Vette Join Date: May 2012
Location: Milford, Michigan
Posts: 3,201
|
Maybe a triathlon. 1/4, stopping, and autocross. I am in for a sc vs turbo vs na comparison. My car was in gm ht once already. I know them well.
__________________
2017 Grand Sport, Borla X Pipe.....Enough Said
|
06-20-2013, 10:55 AM | #662 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
The more the merrier.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread |
06-21-2013, 03:48 PM | #663 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
Just got back from the shop and all the parts were delivered. They had already gone to the machine shop for weighing before they start balancing. Unfortunately, they found out they sent the wrong wrist pins, so we've in a holding pattern until we get the correct ones.
The goal is to get the weight back down from the 14g we added for each piston last time. Aaron is shooting for about +/- 1 g. That will make it easier to balance and hopefully we won't have to add any weight to the crank this time. I've got some pictures of the crank, mains and the bare block I'll upload later. Figured I would share for those that have never seen an LFX torn down before.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread Last edited by GretchenGotGrowl; 06-21-2013 at 03:59 PM. |
06-21-2013, 04:18 PM | #664 |
Track > 1/4 Mile
|
Awesome! You're going all out that's for sure.
__________________
|
06-21-2013, 04:23 PM | #665 |
Cedar Creek Woodshop
|
Badass!
__________________
2014 Black 2SS/RS 1LE
|
06-21-2013, 04:28 PM | #666 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
Yeah, Aaron's on a mission.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread |
06-21-2013, 06:53 PM | #667 |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Nice looking parts - should do well together!
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
06-28-2013, 05:04 PM | #668 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
Little misunderstanding on my part. I thought Aaron way saying he wanted to get the rods, pistons and pins within +/- 1 g of stock weight. What he was saying is with the wrong wrist pins it was already there. Now that we are 21 g less than stock.
The crank will be balanced early next week. They are also going to have to hatch score the cylinder walls because the new compression ring is very thick and much harder. They will need some help seating in. It is a pretty nice setup; all recommended by Wiseco for a car of this displacement and power level. It will take about 2 more weeks to get the everything back in the car and ready for tuning. We are expecting slightly less power because of the ring package, but we'll see.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread |
06-28-2013, 05:29 PM | #669 |
Don't Sleep on My V6
|
Great update can't wait to see numbers.
Sent from Galaxy Note 8
__________________
|
06-28-2013, 06:32 PM | #670 |
Cedar Creek Woodshop
|
That's awesome man!
__________________
2014 Black 2SS/RS 1LE
|
06-29-2013, 08:57 AM | #671 |
Drives: 11 F150 EB/13 Sonic RS/15 Z06 Join Date: Sep 2010
Location: Little Rock, AR
Posts: 7,129
|
Unfortunately I don't have pictures of the new pistons (battery on my phone was getting low), but I did see them. There are some subtle differences. The skirt is a little bit longer and that land has a bit more material below it. The upper ring land is in the same place as the last forged piston but they added gas jets to keep it pressed out at higher RPMs. I had never heard of this but it seems to be common for race pistons (I looked it up before posting so I knew something about it LOL).
Although Aaron couldn't see any signs of blowby but the guys at Wiseco said they could see some and suggested we add the gas porting and stronger compression ring. Hopefully everything is built to handle the power now and we get to put down some good ETs/Traps.
__________________
New Ride -- 2015 Z06 2LZ (stock) -- Journal
Old Ride -- 2012 Camaro 2LT/RS (647 RWHP & 726 RWTQ) -- Build Thread |
06-29-2013, 09:17 AM | #672 |
Cedar Creek Woodshop
|
Keep the money flowing and making the BADDEST B!TCH out there! Can't wait till it's in your garage for good instead of the shop lol
__________________
2014 Black 2SS/RS 1LE
|
|
|
Tags |
best v6, holy crap!, twin turbo lfx, v6 fuel system |
|
|