You are browsing camaro5 
 |
|
05-04-2013, 06:20 PM
|
#1 |
 
Drives: 2010 SS Camaro Join Date: Sep 2009
Location: Orange County, CA
Posts: 177
|
BMR Front Lower Control Bushing Install Help.
Trying to install my BMR (BK018) front control arm bushing and I cant seem to get this bushing installed.
I am hoping someone can please tell me how install this. The instructions simply say "install new bushings" .... so sounds easy enough and makes think I am missing something. Thanks for the help!
__________________
2010 SS, CAI intake, Kooks 1 7/8 LT with high flow cats, Pfadt Sways and Springs, Lloyds Mats, Magnaflow 3"cat back, Ported TB, JRE tune, Rx Catch Can, Forgestar F14, BMR subframe, BMR 4point strut brace.
|
|
|
|
05-04-2013, 06:36 PM
|
#2 |
|
Account Suspended
Drives: 2010 camaro ss Join Date: Nov 2012
Location: Richmond Hill, GA
Posts: 726
|
push.
|
|
|
|
|
05-04-2013, 07:00 PM
|
#3 |
        
Drives: 2010 Cyber Grey Camaro SS (LS3) Join Date: Mar 2010
Location: Clarksville TN
Posts: 2,275
|
I would agree with 429, and also is the outside of the bushing slightly greased?
__________________
GPI SS3 Cam / PRC 255 heads / Forged 376ci bottom / Fore level 2 fuel system / D1SC ProCharger on 12lbs / Alky control dual nozzle / 770 whp / 649 wtq tuned by Ryan Stevens at GPI
|
|
|
|
|
05-04-2013, 07:54 PM
|
#4 |
|
Account Suspended
Drives: 2010 camaro ss Join Date: Nov 2012
Location: Richmond Hill, GA
Posts: 726
|
boil the bushing in water on the stove. makes it gummy. use gloves
|
|
|
|
|
05-04-2013, 11:12 PM
|
#5 |
|
Drives: 2010 SS Camaro Join Date: Sep 2009
Location: Orange County, CA
Posts: 177
|
Thanks I will give it try and let you guys know. Thanks again
__________________
2010 SS, CAI intake, Kooks 1 7/8 LT with high flow cats, Pfadt Sways and Springs, Lloyds Mats, Magnaflow 3"cat back, Ported TB, JRE tune, Rx Catch Can, Forgestar F14, BMR subframe, BMR 4point strut brace.
|
|
|
|
|
05-05-2013, 12:25 AM
|
#6 |
|
Drives: 2010 SS Camaro Join Date: Sep 2009
Location: Orange County, CA
Posts: 177
|
Gotem in.
 Little bit of bearing grease... find your sac and push like hell. BMR instructions states the machined surface should face the front of the vehicle. Does anyone know why. They look identical. Hypothetically speaking if one were stupid enough to put them in backwards would you take them back out and reverse them?
__________________
2010 SS, CAI intake, Kooks 1 7/8 LT with high flow cats, Pfadt Sways and Springs, Lloyds Mats, Magnaflow 3"cat back, Ported TB, JRE tune, Rx Catch Can, Forgestar F14, BMR subframe, BMR 4point strut brace.
|
|
|
|
|
|
|
|
 |
|
|
