Steering wheel audio control diagram - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Cabrera · 03-26-2012, 12:10 PM

Hello. I searched with no luck...

I'm trying to find a wiring diagram of the connectors/wires that are on the steering wheel only, and connect the controls.

I'm trying to figure out if it would be possible to put the just "search" button on the left hand side where there is an empty slot next to the cruise control.

The Stig · 03-26-2012, 12:12 PM

I *think* that it is a single data wire that controls the buttons but I don't know that for sure.

Caddyroger · 03-26-2012, 04:02 PM

Is this the diagram that you was wanting?

The Stig · 03-26-2012, 04:07 PM

yes

thank you

Caddyroger · 03-26-2012, 05:03 PM

Quote:

Originally Posted by stieger

yes

thank you

If my electronic math hasn't failed looks like you just need a 2935 resistor and switch between the pink and light green wires.

2SSRS@Gen5diy · 03-26-2012, 05:34 PM

Quote:

Originally Posted by Caddyroger

If my electronic math hasn't failed looks like you just need a 2935 resistor and switch between the pink and light green wires.

That will not work.

You see all the numbers above the switchs, there resisters with a set value, when you push any switch it sends a signal on the pink wire for the switch you pushed, to the BCM and it does all the work.

Caddyroger · 03-26-2012, 06:06 PM

Quote:

Originally Posted by 2SSRS

That will not work.

You see all the numbers above the switchs, there resisters with a set value, when you push any switch it sends a signal on the pink wire for the switch you pushed, to the BCM and it does all the work.

Ok I was thinking it would have to be 2935 ohms for the source to work since the resistance is in series.

2SSRS@Gen5diy · 03-26-2012, 08:40 PM

I ordered the parts to test today will let you know the outcome.

PS this summers job to make this radio work in the older cars.

Eric Baker · 03-26-2012, 08:41 PM

By my calculations, it's 3025 ohms. Yes, it should work if you get the correct value resistor hooked up to a switch.

amanc96 · 03-26-2012, 09:06 PM

Quote:

Originally Posted by Eric Baker

By my calculations, it's 3025 ohms. Yes, it should work if you get the correct value resistor hooked up to a switch.

I got 3025 for the source as well.

The Stig · 03-26-2012, 09:10 PM

Quote:

Originally Posted by 2SSRS

I ordered the parts to test today will let you know the outcome.

PS this summers job to make this radio work in the older cars.

so excited!!!

Caswell239 · 03-26-2012, 09:16 PM

Quote:

Originally Posted by stieger

so excited!!!

Damn that looks sick, what's that in?

The Stig · 03-26-2012, 09:25 PM

Quote:

Originally Posted by Caswell239

Damn that looks sick, what's that in?

what's what in?

Caswell239 · 03-26-2012, 09:33 PM

I meant to quote the stereo picture. Damn tapatalk I hate it. It says 1LE that's the track pack?

03-26-2012, 12:10 PM	#1
Cabrera Freightrain Coming Ur Way Drives: V8-1968 & V6-2000 & V6 2010 Camaros Join Date: Feb 2010 Location: So Cal Posts: 822	Steering wheel audio control diagram Hello. I searched with no luck... I'm trying to find a wiring diagram of the connectors/wires that are on the steering wheel only, and connect the controls. I'm trying to figure out if it would be possible to put the just "search" button on the left hand side where there is an empty slot next to the cruise control. __________________ Do you serve a purpose, or purposely serve? Last edited by Cabrera; 03-26-2012 at 10:26 PM.

03-26-2012, 12:12 PM	#2
The Stig knows 2 facts about ducks Drives: ...and they're both wrong Join Date: Aug 2009 Location: The HMS Invincible Posts: 25,072 View My Garage	I think that it is a single data wire that controls the buttons but I don't know that for sure. __________________

03-26-2012, 04:02 PM	#3
Caddyroger Drives: 2011 RJT Camaro LT2 RS auto shift Join Date: Dec 2011 Location: Washington state Posts: 1,861	Is this the diagram that you was wanting? Attached Images __________________ Caddy

03-26-2012, 04:07 PM	#4
The Stig knows 2 facts about ducks Drives: ...and they're both wrong Join Date: Aug 2009 Location: The HMS Invincible Posts: 25,072 View My Garage	yes thank you __________________

03-26-2012, 08:40 PM	#8
2SSRS@Gen5diy Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008 Location: By the lake in AZ Posts: 15,719 View My Garage	I ordered the parts to test today will let you know the outcome. PS this summers job to make this radio work in the older cars. Attached Images

03-26-2012, 08:41 PM	#9
Eric Baker Drives: Black/Black 2SS/RS 6M Join Date: Mar 2010 Location: Boston MA Posts: 987 View My Garage	By my calculations, it's 3025 ohms. Yes, it should work if you get the correct value resistor hooked up to a switch.

03-26-2012, 09:33 PM	#14
Caswell239 Drives: 2011 2ss/rs Join Date: Nov 2011 Location: Canada Posts: 1,431	I meant to quote the stereo picture. Damn tapatalk I hate it. It says 1LE that's the track pack?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Diagnostic Trouble Codes (DTCs) for OBD II equipped GM vehicles	steeleshark2	Tuning / Diagnostics -- engine and transmission	11	04-08-2020 10:49 PM
steering position, wheel speed, cruise control brake switch...	hapisok	Tuning / Diagnostics -- engine and transmission	8	10-24-2011 08:07 PM
For sale 4 pack guage cluster, steering wheel control, and pdim	manwitadream	Audio / Visual / Electronics/ Gauges / Nav	13	08-20-2011 03:35 PM
Tires loosing pressure	joepitt	Wheels and Tires Talk Sponsored by The Tire Rack	22	12-11-2010 05:00 PM
USB port	The_Stache	Audio, Video, Bluetooth, Navigation, Radar, Electronics Forum	85	09-20-2009 01:44 PM