06-02-2011, 03:48 PM | #1 |
Drives: 2011 1LT Camaro with RS package Join Date: May 2011
Location: Eastern Passage
Posts: 10
|
Transformers front fender side emblem location
Can anyone tell me exactly where these emblems are supposed to go? i know they go under the Camaro logo, but I'm wondering just how far below the Transformers logo goes. Thanks.
|
06-02-2011, 03:56 PM | #2 |
Drives: 2012 ZL1 - #670 Join Date: Jun 2009
Location: Seminole, Fl.
Posts: 8,009
|
Between the M & A 3/4" below ...
__________________
|
06-02-2011, 04:01 PM | #3 |
Drives: 2011 challengerR/T , 2010 Ram R/T Join Date: Aug 2008
Location: Lafayette Indiana
Posts: 1,186
|
This is where I put mine,hope this helps...
|
06-02-2011, 07:21 PM | #4 |
Account Suspended
Drives: 2010, Rally Yellow, Black stripes Join Date: Jul 2010
Location: Phoenix
Posts: 2,363
|
It seems these emblums are just as high theft as the running horse was on the original Mustang. At $80 bucks a pop, the factory one gets expensive to replace. The ebay one, at about $5, is a whole lot easier on the wallet to replace. (I know it isn't quite as good, but very few people notice)
|
06-02-2011, 07:54 PM | #5 |
Drives: 2011 1LT Camaro with RS package Join Date: May 2011
Location: Eastern Passage
Posts: 10
|
Thanks for the help! :-)
|
06-02-2011, 08:55 PM | #6 |
Account Suspended
Drives: 2013 SS Join Date: Dec 2009
Location: Boyertown, PA
Posts: 1,374
|
Thank you to the OP for posting the question and for SlingShot for posting the information. I'm about ready to do this on mine. Is it exactly 3/4 of an inch below the M&A and is the 3/4 to the center of the bump up in the emblem or to the sides?
|
06-04-2011, 10:44 AM | #7 |
Drives: 2011 Camaro 2LT RS, Red Jewel Join Date: Apr 2011
Location: LA (Lower AlaBAMa)
Posts: 588
|
I put mine about an inch below the wording:
The emblem is super thin, though, and didn't curve to match the contour of the car satisfactorily, so the points stick out at the top and bottom. I'll be removing them and replacing them later to correct that oversight. (As well as the fact that I did get it a little off centre.)
__________________
Still not quite done.
|
05-29-2021, 08:47 PM | #8 |
Drives: 2022 Chevy Camaro 2SS Redline Join Date: Dec 2016
Location: Houston, TX
Posts: 309
|
I found this thread. I will be having some paint work done on my 2011 Camaro 2SS. I will be installing the Transformers autobot emblems. Is the install exactly the way the GM factory would do it? Between the M & A 3/4" inches below the CAMARO letters? Would anyone know the exact spacing from GM directly? Or is this just a guess? The GM emblems are not cheap. I want the install to go smoothly. Any additional advice is welcoming.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Front pass side OE endlink needed | ssmike | Suspension / Brakes / Chassis | 16 | 06-01-2011 07:49 AM |
May 2011 Exterior Specials list GMPARTSHOUSE.COM | patrickt | Exterior Parts & Accessories | 3 | 05-27-2011 12:44 AM |
2010 Chevrolet Camaro TRANSFORMERS Special Edition Announced | thecamaroguy | 5th Gen Camaro SS LS LT General Discussions | 260 | 01-06-2011 07:08 AM |
Check your front fenders | ffrcobra_65 | 5th Gen Camaro SS LS LT General Discussions | 20 | 08-25-2009 06:51 PM |