You are browsing camaro5 
 |
|
06-13-2013, 11:37 PM
|
#1 |
|
Night Fury
|
Front Bow Tie Delete
Has anyone purchased a bow tie delete from Yates performance? If so how did it go? Was it a good piece?
Here is reference pic.
__________________
2014 2LT RS A6
Mods: K&N Intake, Magnaflow Axleback, BMR Strut Tower Brace, VTC Throttle Controller, Tune. |
|
|
|
06-13-2013, 11:38 PM
|
#2 |
|
Teenage Dream Camaro
Drives: A Visually Stunning Camaro Join Date: Feb 2013
Location: Florida
Posts: 1,722
|
A couple of people have, it is a major PAIN to get it off though.
|
|
|
|
|
06-13-2013, 11:40 PM
|
#3 | |
|
Night Fury
|
Quote:
__________________
2014 2LT RS A6
Mods: K&N Intake, Magnaflow Axleback, BMR Strut Tower Brace, VTC Throttle Controller, Tune. |
|
|
|
|
|
06-13-2013, 11:41 PM
|
#4 |
|
Teenage Dream Camaro
Drives: A Visually Stunning Camaro Join Date: Feb 2013
Location: Florida
Posts: 1,722
|
The Bowie. The tabs on the back of the Bowtie will kill your fingers!
|
|
|
|
|
06-13-2013, 11:43 PM
|
#5 |
|
Account Suspended
Drives: nothing Join Date: Nov 2010
Location: a hole
Posts: 17,906
|
You just pull and wiggle the bowtie up and down and it will pop out. It tough on Heritage grill though.
|
|
|
|
|
06-13-2013, 11:53 PM
|
#6 |
         
Drives: Black ZL1 Join Date: Apr 2013
Location: City of Champions, Alabama
Posts: 3,698
|
Ok, so the ZL1 bowtie is the same piece as the others, but the bottom of the four clips is snapped off(I dont know if it's like that on other models or not), but I got a screwdriver wrapped in a microfiber cloth to loosen the sides, being very careful not to scratch up the grill, which didn't go great, but anyway then used a long piece of metal(like a really long flathead screwdriver or something) to slide down inside the hole next to the hood latch and got the top clip loose that way, and that's how I got my bowtie off.
Which I replaced with a new bowtie, not the piece you are talking about
__________________
Check out Alabama Camaros, for Camaro enthusiasts all around Alabama https://www.facebook.com/groups/1739...group_activity
|
|
|
|
|
06-13-2013, 11:54 PM
|
#7 |
Drives: 2011 2SS 6.2L W/RS package Join Date: Jan 2011
Location: Colorado
Posts: 3,008
|
It's not that bad!! Took me 15 minutes to install, and looks a thousand times better then the bowtie..
__________________
 KooKs LT Headers, Borla S-Type cat back, RotoFab CAI, Bo White PTB, RMCR tune... Last edited by ToolFan66; 06-14-2013 at 08:58 PM. |
|
|
|
|
06-13-2013, 11:56 PM
|
#8 |
Drives: 2012 1SS LS3 M6 black on black :) Join Date: May 2012
Location: SD
Posts: 1,342
|
I've had mine on for almost a year. Looks great and wasn't anything too hard to put on.
|
|
|
|
|
06-14-2013, 01:07 AM
|
#9 |
|
It's all hers.
Drives: 2015 ZL1 Join Date: Jan 2012
Location: Djibouti - Horn of Africa / Wellsville NY
Posts: 719
|
I did and it's no big deal. Like said, takes 10 minutes or so and it cleans up the grill quite well.
I recommend it.
__________________
#846
|
|
|
|
|
06-14-2013, 06:00 AM
|
#10 |
|
Team LFX
Drives: Fast Join Date: Mar 2012
Location: TX
Posts: 621
|
15 minutes to install?!?!? It took me a couple of seconds. I just pulled really hard on the bowtie and it came right off, and I didn't break anything. I love my bowtie delete.
__________________
 |
|
|
|
|
06-14-2013, 06:06 AM
|
#11 |
|
Drives: . Join Date: Nov 2012
Location: .
Posts: 1,085
|
It's really easy. You just need to know where to pull from, the taps have edges. It looks like the delete kit is made by Scott Drake.
http://www.phastekperformance.com/20...tie-delete.htm |
|
|
|
|
06-14-2013, 07:22 AM
|
#12 | |
Drives: 2010 2SS RS M6 Join Date: Mar 2011
Location: Cincinnati area
Posts: 1,522
|
Quote:
__________________
Traded-in car: K&N Typhoon intake, JBA Shorty headers, Solo mid-pipes/hi-flow cats, GMPP Track Pack axle-back, Vmax ported TB, Billet Custom catch can, billet tensioner pulley, Hines Hex Vents, Z/TA rear spoiler, ProCustom headlight covers, Drake black/riveted quarter window covers, GM satin fuel door, chrome and brushed caps/covers under the hood, EmblemPros underhood bowtie & fuel rail "Camaro" plates, chrome "SS" door kick-panels, chrome trunk latch plate & strut rods, Street Scene lower grille ducts w/LED lights, front bowtie-delete, Yates Performance pedals, 35% tint, etc.
|
|
|
|
|
|
06-14-2013, 09:53 AM
|
#13 | |
Drives: 2013 Chevy Camaro 2LT 3.6 V6 Join Date: Apr 2013
Location: United States
Posts: 715
|
Quote:
|
|
|
|
|
|
06-14-2013, 09:30 PM
|
#14 | |
|
Drives: 2010 2SS RS M6 Join Date: Mar 2011
Location: Cincinnati area
Posts: 1,522
|
Quote:
__________________
Traded-in car: K&N Typhoon intake, JBA Shorty headers, Solo mid-pipes/hi-flow cats, GMPP Track Pack axle-back, Vmax ported TB, Billet Custom catch can, billet tensioner pulley, Hines Hex Vents, Z/TA rear spoiler, ProCustom headlight covers, Drake black/riveted quarter window covers, GM satin fuel door, chrome and brushed caps/covers under the hood, EmblemPros underhood bowtie & fuel rail "Camaro" plates, chrome "SS" door kick-panels, chrome trunk latch plate & strut rods, Street Scene lower grille ducts w/LED lights, front bowtie-delete, Yates Performance pedals, 35% tint, etc.
|
|
|
|
|
|
|
|
|
 |
| Thread Tools | |
|
|
