machine shops in the dallas area - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

adub4185 · 01-20-2010, 08:27 PM

anyone know of a good machine shop in the dallas area? i am designing a few small parts and want to have them made without getting taken to the cleaners on material costs and the like. maybe someone out there on the forum owns/runs one and can help a fellow member out. shops with CNC capabilities is perferred. thanks!

adub4185 · 01-21-2010, 04:28 PM

24 views and no responses? someone has to know of a decent shop in the area. remember, if i can get these parts made for fairly cheap and if there is enough interest, i would do a limited run for other members out there.

kga10734 · 01-21-2010, 07:58 PM

Don't know about the Dallas area, but in the Houston area the hourly rate for machine work isn't cheap especially cnc rates. I work at a machine shop and have done it for almost 23 years now. Material cost are up as well.

eynigush · 01-21-2010, 08:03 PM

Get a hold of g-townmach. I believe he lives in central Texas. Check ou his thread below.

--Eddie

http://www.camaro5.com/forums/showthread.php?t=61445

fastred · 01-22-2010, 06:37 PM

Contact Ron at Micron Applied Technologies. Local job shop, CNC equipped, can build any parts you need for your Camaro.

Micron Applied Technologies
693 Metro Park #24
Lewisville, TX 75057

972-219-8458

partsguy · 02-02-2010, 10:57 AM

hey get a hold of snl performance. i believe its snlperformance.com. they will know of someone. they mite do it. not sure. i personally know a few people up there and there great guys and do amazing work. their in haslet near ftw or flower mound.

01-20-2010, 08:27 PM	#1
adub4185 Drives: 2010 2SS RS, 2023 Camaro ZLE Join Date: Oct 2009 Location: Dallas, TX Posts: 632	machine shops in the dallas area anyone know of a good machine shop in the dallas area? i am designing a few small parts and want to have them made without getting taken to the cleaners on material costs and the like. maybe someone out there on the forum owns/runs one and can help a fellow member out. shops with CNC capabilities is perferred. thanks!

01-21-2010, 07:58 PM	#3
kga10734 Don't Feed the Troll Drives: 2010 Camaro 2LT/RS & 1999 Corvette Join Date: Jun 2009 Location: Montgomery, TX Posts: 774	Don't know about the Dallas area, but in the Houston area the hourly rate for machine work isn't cheap especially cnc rates. I work at a machine shop and have done it for almost 23 years now. Material cost are up as well. __________________

01-21-2010, 08:03 PM	#4
eynigush SoCal C5 Family Member Drives: 2010 Camaro SSRS Rally Yellow Join Date: Oct 2009 Location: San Diego, CA Posts: 412 View My Garage	Get a hold of g-townmach. I believe he lives in central Texas. Check ou his thread below. --Eddie http://www.camaro5.com/forums/showthread.php?t=61445 __________________ Kooks 1 7/8 headers w/high flow cats Magnaflow Cat-back Competition Series Cold Air Intake by CAI Inc.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Dallas Area - Sony - PlayStation 3 (160GB) with Uncharted: Drake's Fortune $350	Crowley	Members Classifieds - Non-Automotive	3	12-07-2009 08:07 AM
Houston Area Speed Traps & Ticket Stories	crzycicada	USA - Texas	2	10-13-2009 08:16 PM
Dallas Area - Sony - PlayStation 3 (160GB) with Uncharted: Drake's Fortune $375	Crowley	USA - Texas	0	09-04-2009 11:30 AM
Saw a yellow SS in Dallas area.	kmdrum79	Camaro Photos \| Spyshots \| Video \| Media Gallery	23	03-30-2009 04:13 PM
Engine Swap Shops in Maryland area	Guy withda bowtie	General Automotive + Other Cars Discussion	5	06-14-2007 04:47 PM

01-21-2010, 04:28 PM	#2
adub4185 Drives: 2010 2SS RS, 2023 Camaro ZLE Join Date: Oct 2009 Location: Dallas, TX Posts: 632	24 views and no responses? someone has to know of a decent shop in the area. remember, if i can get these parts made for fairly cheap and if there is enough interest, i would do a limited run for other members out there.

01-22-2010, 06:37 PM	#5
fastred Drives: 2010 Camaro, 2007 Z06, 1967 SS Join Date: Jul 2009 Location: Texas Posts: 16 View My Garage	Contact Ron at Micron Applied Technologies. Local job shop, CNC equipped, can build any parts you need for your Camaro. Micron Applied Technologies 693 Metro Park #24 Lewisville, TX 75057 972-219-8458

02-02-2010, 10:57 AM	#6
partsguy Drives: 2004GTO Join Date: Feb 2010 Location: frisco Posts: 24	hey get a hold of snl performance. i believe its snlperformance.com. they will know of someone. they mite do it. not sure. i personally know a few people up there and there great guys and do amazing work. their in haslet near ftw or flower mound.