10-17-2011, 06:44 PM | #239 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
Fine.. Here's what I got for now. Phone died and my camera's battery is dead. Deepcycle dead. Even my voice recorder ran out of batteries. I kid you guys not.
|
10-18-2011, 06:38 PM | #240 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
|
10-18-2011, 07:23 PM | #241 |
|
exhaust sounds good! now fix your damn vents!!!!!
|
10-18-2011, 08:26 PM | #242 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
What about my damn vents? Got 'em aimed where I need 'em and no need for gauges.. yet.
|
10-19-2011, 11:46 AM | #243 |
Butter Bar!
Drives: 2011 SS, 1998 Trans Am Join Date: Dec 2010
Location: Patrick AFB, FL
Posts: 1,364
|
Tips hittin the bumper or just too wide? Could get an exhaust shop to massage them on there.
__________________
2011 Camaro SS, White/Orange, LSR Short Throw, CAI
1998 Trans Am, Red, H/C/I, 3200 CircleD Stall, full suspension 2004 GSXR 1k, Matt Mladin Edition |
10-19-2011, 12:14 PM | #244 |
|
they should be lined up like drunken soldiers!!! As seen in this pic.
|
10-19-2011, 12:58 PM | #245 | |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
Quote:
I'd have to cut back the exhaust as well for the tips to actually tuck under properly. Not to mention I need to buy an aftermarket hangar on the right side to bring the pipe down an inch or so. In the end I'm going to just lower the outs a bit and run them without tips until I can decide. I actually like the look as is with the pipes just hidden/tucked under the cover. As for my vents: I actually USE them. Not just for decoration. Sorry if you forget that this is also my DD so if I want heat or air.. |
|
10-21-2011, 09:05 PM | #246 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
After a few modifications to lower the exhaust..
|
10-21-2011, 10:16 PM | #247 |
|
looking good
__________________
2001 Camaro V6
2016 Camaro 2SS |
10-22-2011, 05:49 AM | #248 |
|
you shouldnt have to worry about melting anything, my stock tips come to about the same place and i have not melted my plasti dip yet
|
10-22-2011, 02:16 PM | #249 |
SS #2431
Drives: 2001 Pewter Camaro SS Join Date: Jul 2009
Location: Missoula, MT
Posts: 1,224
|
the dialogue of that video is almost as good as the exhaust. If I walked by I woulda asked myself "why's that guy talkin to himself? friggin trans am owners..."
__________________
2001 SS Lid, LT's, 3" Y to 4" Borla XR-1 dumped, LCA, LCA Brackets, Dbl. Adj. Panhard, Subframe Connectors, Shock Tower Brace, Eibach Prokit, Eddlebrock Shocks, C6 ZR1 Wheels 18x9.5 |
10-22-2011, 02:25 PM | #250 |
|
__________________
2001 Camaro V6
2016 Camaro 2SS |
10-22-2011, 02:29 PM | #251 |
|
at least our exhausts dont drag on the ground
|
10-22-2011, 02:33 PM | #252 |
|
Only on remys car haha . My exhaust is just fine
__________________
2001 Camaro V6
2016 Camaro 2SS |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
3rd Gen Camaro Street Stock build thread (dialup beware) | zlathim | 3rd Generation Camaros | 9 | 12-06-2018 10:30 AM |
Tom Henry Racing THR22 2010/LS3/IBM/Supercharged SS Camaro [COTW 10/29/12] | GTAHVIT | Member Car Journals | 5217 | 06-27-2016 08:14 AM |
APF "Stage II" Turbo Build Thread | 2010 Camaro SS! | Trevor@APF | Forced Induction - V8 | 1 | 01-19-2010 06:50 PM |
My 1983 Trans Am Build | BowtieGuy | General Automotive + Other Cars Discussion | 14 | 11-09-2008 03:58 PM |