10-20-2013, 11:22 PM | #1 |
Account Suspended
|
Anyone with a havoc rear diffuser??
I just ordered the havoc rear diffuser for my camaro and was looking around at others and was curious if anyone installed it themselves and if so how difficult was the install?
|
10-20-2013, 11:35 PM | #2 |
Drives: 2011 2SS 6.2L W/RS package Join Date: Jan 2011
Location: Colorado
Posts: 3,008
|
It's easy to do, just watch the video on how take off the rear bumper, and your golden..
__________________
KooKs LT Headers, Borla S-Type cat back, RotoFab CAI, Bo White PTB, RMCR tune... |
10-21-2013, 12:34 AM | #3 | |
Drives: 2017 Corvette Grand Sport Join Date: May 2010
Location: Central NJ
Posts: 10,870
|
Quote:
And to take the bumper off is nothing more then 6 bolts, 3 on the under side of each rear wheel well, then its just disconnecting the tail light harness and popping it off.
__________________
|
|
10-21-2013, 12:47 AM | #4 |
Mayhem SS
Drives: 2010 2SS/RS L99 SW/IOM Join Date: Nov 2009
Location: ROMA, TX
Posts: 949
|
I've always wanted this rear diffuser, that or getting the 1LE and corsa ZL1 exhaust
__________________
Mayhem SS - 6.2, Roto-Fab CAI, Pacesetter Headers/Magnaflow X-pipe, Built by TMS, Tuned by File
La Muerte Z71 - Stock 5.3 Tuned by File |
10-21-2013, 06:32 AM | #5 | |
Drives: 2010 CAMARO 2SS/RS WHITE Join Date: Jan 2011
Location: PENSACOLA FLORIDA
Posts: 1,210
|
Quote:
I just got mine on last week, but I can't tell you if it is easy to put on. GARY'S CUSTOMZ painted the part & I let him do the install. Gary did a great job, so for ME, it WAS easy! Post some pics of the rear when you finish!
__________________
|
|
10-21-2013, 09:10 AM | #6 |
I will agree with everyone else it was easy. Just take your time. Here is a Picture of mine.
|
|
10-21-2013, 09:43 AM | #7 |
Account Suspended
|
I know the bumper isn't bad to take off. I had to pull it off when I took the stock diffuser off. I was just reading the instructions oine and it seems like a lot of clips so I was kinda sketchy on how difficult the install was. Seems like everyone says it's pretty easy. I'm sending it to paint once I get it so once I get her back ill attempt the install.
|
10-21-2013, 09:56 AM | #8 |
AKA "Beefcake"
Drives: 2023 ZL1 Sharkskin Join Date: Oct 2009
Location: Indy
Posts: 8,529
|
it is very easy to do. If you have had the bumper off before, you have already tackled the hardest part. Some of the clips are little 'resistant' to come out, but they do. You should not have any issues getting it installed. Mine has been on for 2 years, zero issues.
|
10-21-2013, 05:10 PM | #9 |
Drives: '10 Blk Camaro SS/'08 Blk Silverado Join Date: Feb 2011
Location: OKLA
Posts: 466
|
Here's mine...If your a hands on kind of person this will be challenging but not impossible but if not you should let a body shop or get help from friends depending on your skill levels!
|
10-21-2013, 05:17 PM | #10 |
Drives: 2011 RED Camaro Join Date: Sep 2011
Location: Walnut Creek, CA
Posts: 553
|
Easy install. Heres mine.. I havnt put my exhuast back on so dont mind the empty exhuast holes.
__________________
|
10-21-2013, 06:59 PM | #11 |
Drives: Silver 2010 SS Camaro Join Date: Jul 2009
Location: TN
Posts: 2,562
|
Did you have to trim any on these? I put mine on and have a gap...
__________________
MODS:
ADM built 417, 2.9L Whipple with 3.250 pulley, ADM ported and polished LSA heads,ADM stage3 cam,ADM LSA belt drive system,ADM CAI race scoop, ADM dual fuel pumps, ID 850's, BMR full suspension, Gforce 9 inch kit with 3.5 inch driveshaft, Street Slayer twin carbon clutch, Lingenfelter oil seperator. Tuned by built by ADM Performance, 763rwhp,705rwtq |
|
|
|
|