INSTALLED Light Wurkz Orion V2 Halo Rings - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

2FST2LIV2YNG2DY · 03-16-2011, 01:51 AM

so finally this weekend i took the time to work on my headlight mod. The process with the headlights wasnt too bad but when it came time to remove my bumper... oh my goodness, it was hell cause i have big hands and arms and when i had to get that last screw on top inside the fender well.... jeezus christmas what an experience! anyways, here are a few photos a long the way...and i think it was well worth the trouble!

PIC1: after i finally pryed apart my headlight, make sure to remove any factory glue so u can seal it back up when done

PIC2: remove the little hex screws from the inner frame

PIC3: this is what i used to glue the halo on to the headlight frame

PIC4: glued the halo on to the housing frame

2FST2LIV2YNG2DY · 03-16-2011, 01:53 AM

PIC5: this is how it looks when the glue sets

PIC6 and 7: i used one inverter per halo

PIC8: this is where i decided to mount the halo inverter

PIC9: installed the housing frame back to the headlight lense

2FST2LIV2YNG2DY · 03-16-2011, 02:01 AM

PIC10: during the process, i decided i wanted to paint the headlight housing flat black so my halos can stand out more and later i will install HID's in my fogs

so i went for it!
I removed the part that i didnt want painted which was the turn signal reflector

PIC11: i sanded the headlight reflector

PIC12: applied primer to the headlight reflector

PIC13: painted the headlight reflector flat black

PIC14: drilled a small hole in the area with the red circle to get the wires out and reinstalled the turn signal reflector

PIC15: took a break and ate some nice delicious home cooked rice with sauteed veggies and shrimp because the next part u want done right or your halo will be introduced to rain lol

2FST2LIV2YNG2DY · 03-16-2011, 02:16 AM

PIC16: got my silicone and rubber gloves ready cause its gonna get dirty

PIC17 and 18: i applied a little bit of glue in some areas to hold it tight so i can create a nice seal around the entire headlight. Dont be afraid to get your hands dirty and i recommend wearing rubber gloves so that u can move the silicone around to where u need it to be. make sure to apply enough glue so that it blocks any water from getting in, in other words, dont be stingy with the silicone.

PIC19: finally after 2-3 hours trying to remove the fascia lol. seriously, trying to get to that top screw in the fender was a 8itch! that took about an hour lol sorry for the cloudy pic

2FST2LIV2YNG2DY · 03-16-2011, 02:21 AM

PIC20: this is how i wired mine, its personal preference. i wired them to the parking lights so when i turn the switch to enable the parking lights, my halos turn on.

The passenger side Halos brown (-) wire is connected to the black wire on the parking light harness and the halos white (+) wire is connected to the next wire over which is brown/white on the harness. The Driver side Halos brown (-) wire is connected to the black wire on the parking light harness and the halos white (+) wire is connected to the next wire over which is purple on the parking light harness. Heres an example...

2FST2LIV2YNG2DY · 03-16-2011, 02:40 AM

PIC21: installed the headlights and getting ready to fire em up...

PIC22: ...and voila!! I present to you Light Wurkz Umnitza OrionV2Rings

So what do yall think?

christianmotox · 03-16-2011, 02:43 AM

The halos look good, But i dont understand how are you gona drive at night and how are you not going to get a ticket??

But like i said, those Halos look really good

2FST2LIV2YNG2DY · 03-16-2011, 02:48 AM

Quote:

Originally Posted by christianmotox

The halos look good, But i dont understand how are you gona drive at night and how are you not going to get a ticket??

But like i said, those Halos look really good

thanks!
i did the same thing with my last car and had no issues, all i did was add HIDs to my fogs and i was good

erk5000 · 03-16-2011, 04:53 AM

Are you going to use projectors since you blacked out your reflectors? How are HID's supposed to reflect from black paint?

2FST2LIV2YNG2DY · 03-16-2011, 09:40 AM

Nooooooo. I'm converting my fogs to HID's not the headlights. I said it like 2 times.

Sent from my iPhone 4 using Tapatalk

jagan323 · 03-16-2011, 09:47 AM

lol... so you are just going to leave the headlights not functioning? lol... This is different, that's all i can say really

2FST2LIV2YNG2DY · 03-16-2011, 10:03 AM

Quote:

Originally Posted by jagan323

lol... so you are just going to leave the headlights not functioning? lol... This is different, that's all i can say really

I like the look of the halo with blacked out background. I like fogs with HID's installed. I have enough light just by the HID fogs, I'm not blind lol. Its all personal preference and it works for me and that's all I can say :-)

Sent from my iPhone 4 using Tapatalk

1969to2010 · 03-16-2011, 10:11 AM

I had thought of doing it this way and it has the look I wanted. looks great brother, we decided to just tint the healdlight assembly and add HIDs which worked for us the will be fine. Good luck and props for doing it your way

here is how we did ours
http://www.camaro5.com/forums/showthread.php?t=129679

2FST2LIV2YNG2DY · 03-16-2011, 10:15 AM

How about I get one of these if it makes u feel better lol

Sent from my iPhone 4 using Tapatalk

03-16-2011, 01:51 AM	#1
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	INSTALLED Light Wurkz Orion V2 Halo Rings so finally this weekend i took the time to work on my headlight mod. The process with the headlights wasnt too bad but when it came time to remove my bumper... oh my goodness, it was hell cause i have big hands and arms and when i had to get that last screw on top inside the fender well.... jeezus christmas what an experience! anyways, here are a few photos a long the way...and i think it was well worth the trouble! PIC1: after i finally pryed apart my headlight, make sure to remove any factory glue so u can seal it back up when done PIC2: remove the little hex screws from the inner frame PIC3: this is what i used to glue the halo on to the headlight frame PIC4: glued the halo on to the housing frame

03-16-2011, 01:53 AM	#2
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	PIC5: this is how it looks when the glue sets PIC6 and 7: i used one inverter per halo PIC8: this is where i decided to mount the halo inverter PIC9: installed the housing frame back to the headlight lense Last edited by 2FST2LIV2YNG2DY; 03-16-2011 at 02:29 AM.

03-16-2011, 02:01 AM	#3
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	PIC10: during the process, i decided i wanted to paint the headlight housing flat black so my halos can stand out more and later i will install HID's in my fogs so i went for it! I removed the part that i didnt want painted which was the turn signal reflector PIC11: i sanded the headlight reflector PIC12: applied primer to the headlight reflector PIC13: painted the headlight reflector flat black PIC14: drilled a small hole in the area with the red circle to get the wires out and reinstalled the turn signal reflector PIC15: took a break and ate some nice delicious home cooked rice with sauteed veggies and shrimp because the next part u want done right or your halo will be introduced to rain lol Last edited by 2FST2LIV2YNG2DY; 03-16-2011 at 02:34 AM.

03-16-2011, 02:16 AM	#4
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	PIC16: got my silicone and rubber gloves ready cause its gonna get dirty PIC17 and 18: i applied a little bit of glue in some areas to hold it tight so i can create a nice seal around the entire headlight. Dont be afraid to get your hands dirty and i recommend wearing rubber gloves so that u can move the silicone around to where u need it to be. make sure to apply enough glue so that it blocks any water from getting in, in other words, dont be stingy with the silicone. PIC19: finally after 2-3 hours trying to remove the fascia lol. seriously, trying to get to that top screw in the fender was a 8itch! that took about an hour lol sorry for the cloudy pic Last edited by 2FST2LIV2YNG2DY; 03-16-2011 at 02:36 AM.

03-16-2011, 02:21 AM	#5
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	PIC20: this is how i wired mine, its personal preference. i wired them to the parking lights so when i turn the switch to enable the parking lights, my halos turn on. The passenger side Halos brown (-) wire is connected to the black wire on the parking light harness and the halos white (+) wire is connected to the next wire over which is brown/white on the harness. The Driver side Halos brown (-) wire is connected to the black wire on the parking light harness and the halos white (+) wire is connected to the next wire over which is purple on the parking light harness. Heres an example... Last edited by 2FST2LIV2YNG2DY; 03-16-2011 at 02:42 AM.

03-16-2011, 02:40 AM	#6
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	PIC21: installed the headlights and getting ready to fire em up... PIC22: ...and voila!! I present to you Light Wurkz Umnitza OrionV2Rings So what do yall think?

03-16-2011, 02:43 AM	#7
christianmotox Drives: ( . )( . ) Join Date: Feb 2010 Location: San Diego, CA Posts: 2,827	The halos look good, But i dont understand how are you gona drive at night and how are you not going to get a ticket?? But like i said, those Halos look really good

03-16-2011, 04:53 AM	#9
erk5000 Drives: 2010 Camaro 2SS L99 SIM Join Date: Feb 2010 Location: Oceanside, CA Posts: 1,036	Are you going to use projectors since you blacked out your reflectors? How are HID's supposed to reflect from black paint?

03-16-2011, 09:40 AM	#10
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	Nooooooo. I'm converting my fogs to HID's not the headlights. I said it like 2 times. Sent from my iPhone 4 using Tapatalk

03-16-2011, 09:47 AM	#11
jagan323 I have no life Drives: 06' Subaru STI, ex-Camaro V6 LLT Join Date: Apr 2010 Location: Top Gear Test Track Posts: 3,189	lol... so you are just going to leave the headlights not functioning? lol... This is different, that's all i can say really __________________ List of Camaro DIY The Blog

03-16-2011, 10:11 AM	#13
1969to2010 The Man in Black Drives: 1969 Camaro 2010 Camaro 1SS Join Date: Apr 2009 Location: Long Island NY Posts: 2,016	I had thought of doing it this way and it has the look I wanted. looks great brother, we decided to just tint the healdlight assembly and add HIDs which worked for us the will be fine. Good luck and props for doing it your way here is how we did ours http://www.camaro5.com/forums/showthread.php?t=129679 __________________

03-16-2011, 10:15 AM	#14
2FST2LIV2YNG2DY ...this is my addiction! Drives: SOLD Join Date: Jul 2010 Location: AZ Posts: 1,287	How about I get one of these if it makes u feel better lol Sent from my iPhone 4 using Tapatalk

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
HALO light bulb question	2Muchmark	Cosmetics and Lighting Modification Discussions	30	11-07-2013 07:00 AM
Red led halo light	Cpiend4765	Cosmetics and Lighting Modification Discussions	81	04-17-2013 02:44 AM
New information on the Halo light issues some have had	BlackIce1066	5th Gen Camaro SS LS LT General Discussions	4	04-09-2011 03:55 PM
FS: New White Halo Rings for RS/Non RS Headlights	coreyt	Exterior Parts & Accessories	5	06-17-2010 12:05 AM
Stock Chrome Tail Light Rings	GJG	Cosmetics and Lighting Modification Discussions	3	06-07-2009 08:38 AM