05-17-2015, 04:44 PM | #85 |
Jan
Drives: 2010 Camaro 1LT Red Jewel tintcoat Join Date: May 2010
Location: Springfield, TN
Posts: 16,225
|
I got to test my BMR springs out today at an autocross in Nashville. It felt great. Now I just need to get better. Thanks Chase (AKA Apex Motorsports)!
__________________
|
05-20-2015, 07:38 AM | #86 |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
|
05-21-2015, 11:48 AM | #87 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
ok................
Any of you guys have a problem when installing the BMR spring? I went to install mine last night and I cant get the spring to center itself on the top hat. The little washer that holds the bump stop is resting on one coil in the spring. Couple of people said it may need the weight of the tire and vehicle for it to align itself so I went ahead and installed both front springs.......Drove it to work today(10miles) and then going straight back home to get under her to see if the spring did settle or not. Anyone else have this problem? |
05-21-2015, 12:42 PM | #88 | |
Drives: Camaro Justice Join Date: Jun 2007
Location: Virginia
Posts: 20,174
|
Quote:
|
|
05-21-2015, 02:04 PM | #89 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
Let's see if I can upload pix off my phone.....
|
05-21-2015, 02:06 PM | #90 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
Pic #2
|
05-22-2015, 11:50 AM | #91 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
Please?
|
05-22-2015, 10:44 PM | #92 |
Drives: Camaro Justice Join Date: Jun 2007
Location: Virginia
Posts: 20,174
|
Hmmm.
The coil doesn't need to fully seat to the upper insulator / seat, but it should sit in the seat. When the car is lifted and the wheel at full droop, is the coil loose in the assembly or tight? |
05-23-2015, 09:56 AM | #93 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
The assembly is tight
|
05-25-2015, 12:43 PM | #94 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
I really feel bad if nobody has ever had this happen to them lol geez.....
|
05-25-2015, 01:10 PM | #95 |
The gritos pollo!!!
|
Is the coil upside down?
__________________
______
If you don't stop how can they give you a ticket?-The Big Tuna___ '12 1Ls Camaro; Slp loud mouth I|maganflow x-pipe|Injen long ram intake|brembo brake upgrade| russell s.s. lines|2LT polished 19's|billet 5mm spacers|tinted tail lights&markers|pdmi|billet c. can| '13 Avenger R/T '77 T/A 6.6;, draining my wallet. |
05-25-2015, 03:17 PM | #96 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
I do believe it is installed right side up. The lower coil is a bigger diameter than the top one. I took them off again and here's a couple of pix to explain a little more about the dilemma lol
|
05-25-2015, 03:19 PM | #97 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
Pic 1
|
05-25-2015, 03:24 PM | #98 |
Drives: 2015 2SS....white Join Date: May 2015
Location: Katy, TX
Posts: 527
|
The BMR coil doesn't seat itself on that yellow part, like the oem one does. It's touching the washer that is on the strut. I have tried to seat it myself while someone else tightens the nut on top, as soon as I let it go, it just pops right back out
|
|
|
Tags |
apex lowering springs, apex motorsports, best lowering springs, camaro lowering springs |
Thread Tools | |
|
|