02-03-2011, 05:13 AM | #1 | ||||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
Quote:
what all is it doing now? Quote:
yeah. I'm just trying to spec you out parts, and I got off early yesterday so I didnt do much of anything. first off skip the roller tip rockers, either go full roller or leave the stockers, save the money for the pushrods and spend it on rockers. that cam seems overpriced IMO. IIRC, you can get a custom grind for ~$350 or so. stock pushrods are capable of .650 lift, so that money could be spent elsewhere
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
||||
02-03-2011, 08:20 AM | #2 | |||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
Quote:
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
|||
02-03-2011, 06:45 PM | #3 | |
PWA Relapse
|
Quote:
As for pushrods, I don't mind reusing the stocks I just figured since I was thinking of upping the rev-limiter to 6500 and the car has 114xxx on it, I might want to look into hardened pushrods. I think I might remove the crank from the parts list also though because upon further consideration, an aftermarket cast crank wouldn't be any better than the stock crank and I'd have to get it balanced anyway. Might as well just reuse the stocker. - X P.S. - I can get the cam here for 335, which seems to be as good a deal as any of the other cams.
__________________
2017 1LT/RS A8 Hyper Blue Metallic |
|
02-04-2011, 06:57 AM | #4 | |||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
Quote:
you can up the rev limiter to 7k if you want. the stock bottom end of these cars is twice as strong as most people give it credit for. Here’s what I was running in my 94Z with 12.5 cr 230 / 240 - .544/.576 - 110 LSA with a stalled A4, full bolt-ons, handported heads/intake, and some spray IIRC, I paid around $350 for that cam (somewhat custom grind) 4 years ago another option http://www.lingenfelter.com/sites/li...mationv1.3.pdf and another option is Comp Cams XE 230/236 if you can find it. I've seen some here an there used go for less than $200 also, you need to get some good springs/hardware to compliment the cam as well. I was running 918's for a while till they started having failures (not my personal ones, but Comp started farming out the manufacture of their springs and less quality came about). I switched to PAC 1518s that are good to .650 lift. the 1218s are good to about .600 lift and the 918's are about .625 lift. I didn't see anything listed on the springs you had selected on what their max lift was. also... you should do this in the 4th gen section. lol and find some heads or have yours ported to maximize the cam.
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
|||
02-04-2011, 11:33 AM | #5 | |
PWA Relapse
|
Quote:
Not sure on their max lift. I'll look that up also. - X
__________________
2017 1LT/RS A8 Hyper Blue Metallic |
|
02-04-2011, 11:52 AM | #6 | |||
Truth Enforcer
Drives: anything I can get my hands on Join Date: Sep 2006
Location: anywhere and everywhere
Posts: 22,797
|
Quote:
I'm not wanting you to go with the biggest donkey di*k cam you can. even mine wasn't the biggest around. mine was set up for 40/60 split of track and dd. tho it was nicknamed the ThunderFu*k II cam...lmao you have the benefit of the m6 that you dont have to fight as hard for idle characteristics or cam surge with a converter.
__________________
Never race anything you can't afford to light on fire and push off a cliff
A group as a whole tends to be smarter than the smartest person in that group until one jackass convinces everyone otherwise. Quote:
Quote:
|
|||
02-04-2011, 12:21 PM | #7 | |
PWA Relapse
|
Quote:
Also, that LPE cam looks like it would work as well. Also, those crane springs have an install height of 1.750 and a coil bind of 1.080, so they should be good for at least .600 or .650 of lift. Since I wouldn't be running anywhere close to that, they should be fine. - X
__________________
2017 1LT/RS A8 Hyper Blue Metallic |
|
11-15-2011, 07:20 PM | #8 | |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
Zabo's '00 T/A Build Thread
With the resurrection over, I decided to have the previous thread locked and relaunch the build thread in this thread.
Long short of my ownership: - Found it wandering lots back in June 2010 - Placed a deposit, and swept it off the lot within 5 days of it's arrival there. - Said dealership was a Ford stealership - Needed Brakes and other minor work from sitting (29,718 miles) - Drove trouble free (and learned to drive stick in the process) THROUGH THE WINTER of 2010/2011 - April 2, 2011 the car was totaled in a drag racing accident (sanctioned IHRA track). - Secured a loan on the verge of bankrupting myself and rebuilt the car. - Bill: $10,300; paid $10,395 for the car. - Replaced door emblems with NOS 1998 Sport Gold Metallic emblems - Rear bumper cover given the CETA (Collectors Edition Trans Am) blackout treatment - Replaced the factory rear after discovering that the Torsen was KIA 10/2011 - Installed WS6 short stick, custom made 'Bandit shifter knob' from a 1977 Special Edition Trans Am, and TSB Rumbler Exhaust - Purchased and installed AP tips, tucked TSP to gain a few inches in clearance - Dropped the car off at Backstreet Performance in Medina and had the LTs and ORY installed, as well as the EGR pulled. Had them also reset the car for the lack of EGR/Cats/O2s To do list: - Weld up Cutout section and pick up/wire up an electric valve - Purchase/install a Y pipe brace - Install Prothanes - Get a Daily Driver! - GET A BETTER PAYING JOB! - Pick up a set of Speedlines and widen rears to 11" for 315 rears - Remount old tires on current PA6s for spare/storage use - Put it away.. Down the road a few years: - Strip the whole car - Reweld the core support ('05 accident) - Realign/Reweld (4/2/11 accident) - Build/Swap the rear for road racing - Build the transmission - Respray in a custom factory Maple Red/Gold Flake mix - Overhaul/breakdown and clean engine And Pictures: THE EARLY DAYS! Finally got her home late in the evening.. Butt shot! Interior when I got her home (not so pretty now.. and the stick shrunk) Mileage when I got her home. '00 Spec LS1 First good wide angle shot of the car 303hp at the rears w/ injector cleaner and clogged cats! 4/2/11 4/2/11. DO NOT CLICK IF YOU HAVE AN AVERSION TO AUTOMOTIVE GORE!! Yeah.. it hit that hard. To this day the wheel still holds pressure. o_o On the frame puller after welding/sealing Welcome Home! (yes, that is a welcome home sign, parents made it) WS6 SHORT STICK! Stock spongey stick.. WS6 short stick! (6.5" model) SLP BANNER! Club banner decal NEW FILLER PANEL! Good bye faded filler panel.. Hello refurbished factory unit! T/A NATIONALS! Judging line, T/A nats 2011! BANDIT KNOB! Bandit knob prior to install Completed Bandit knob! EXHAUST! Soon.. very soon Out with the old In with the BOOM! Bow to my thunderous roar! Youtube video testing my (at the time) new iPhone and making a proper recording of the exhaust TIPS! -AP Stainless Dual Dual 3" Ovals LONGTUBES & CATTED ORY!! Pacesetter 1 3/4" and Pacesetter 3" Catted (aftermarket high flows) Y pipe Last edited by Zabo; 07-24-2012 at 11:00 PM. |
|
11-15-2011, 07:34 PM | #9 |
|
__________________
2001 Camaro V6
2016 Camaro 2SS |
11-15-2011, 11:08 PM | #10 |
|
so ummm....when ya gonna do something new to it
|
11-16-2011, 06:10 AM | #11 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
|
11-16-2011, 08:39 AM | #12 |
|
It looks 100% better. Nice work
__________________
2001 Camaro V6
2016 Camaro 2SS |
11-16-2011, 09:36 AM | #13 |
|
you need an LS6 intake too Zabo!
|
11-16-2011, 11:38 AM | #14 |
Gunning for Sixth
Drives: '03 ZR2 Blazer Join Date: Sep 2008
Location: Woodhaven, Michigan
Posts: 9,358
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
OK...I'm starting a better V6 exhaust examples thread!! | KMPrenger | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 611 | 07-01-2020 08:49 AM |
Ph4r's Car - Boobies - Build Thread | Ph4r | Member Car Journals | 42 | 03-20-2013 06:09 PM |
Camaro5 Fest II Caravan/Convoy Thread | tribone | 2011 Camaro5 Fest (II) | 13 | 04-12-2011 02:22 PM |
Dumbest Camaro5 Question EVER! | Beemer | 5th Gen Camaro SS LS LT General Discussions | 209 | 05-23-2010 06:11 PM |