|
View Poll Results: T Tops or Carbon Fiber? | |||
T Tops | 14 | 73.68% | |
Carbon Fiber Conversion (Fenders, doors, etc) | 5 | 26.32% | |
Voters: 19. You may not vote on this poll |
|
Thread Tools |
05-12-2011, 11:26 AM | #225 |
Prefer to be blown!
Drives: 2010 Silver/Black 2SS/RS Manual Join Date: Mar 2010
Location: Nor-Cal
Posts: 2,677
|
That and smaller brakes so you can get some good racing slicks on the back. Don't forget to order a line lock kit, you will need it to heat up the drag radials. The 555s are just a slippery as the stock tires when they are cold.
__________________
MagnaCharger TVS-2300 550rwhp 540 rwt and a radical suspension under the car.
|
05-12-2011, 11:31 AM | #226 |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
only 800 because of the octane issue with gas....havent really thought about the rear end except for getting the pfadt bushings; gunna look into getting work done to it while my engine is being rebuilt (if i decide to do that)l
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
05-12-2011, 11:32 AM | #227 | |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
Quote:
i ordered my flameproof jacket last night and roll cage is gunna be installed pretty soon too
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
|
05-12-2011, 11:37 AM | #228 |
Prefer to be blown!
Drives: 2010 Silver/Black 2SS/RS Manual Join Date: Mar 2010
Location: Nor-Cal
Posts: 2,677
|
Yes, the cost is ~$150.
__________________
MagnaCharger TVS-2300 550rwhp 540 rwt and a radical suspension under the car.
|
05-12-2011, 11:55 AM | #229 |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
where are you mounting the actual controls in your car? and i still havent done a burnout since the supercharger went on!! i rolled right past the waterbox last wed nite!
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
05-12-2011, 12:07 PM | #230 |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
went by Blu808 last night. im painting my calipers red. also got to hear how my car sounds with open headers......DAMN!! freakin loud. cant wait to try it out on the freeway under boost . rotors went on last night as well.....now if only my brake lines would arrive!
found out my gauge pod will ship tomorrow as well as the carbon fiber fenders i ordered. everything should be here next week. We decided to just replace my broken axel with another stock one for now. I'm going to get my 1400hp axels ordered in the next week or so, most likely from DSS.
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
05-12-2011, 01:26 PM | #231 |
The driveshaft on our race car was replaced with a DSS aluminum unit.
|
|
05-12-2011, 03:53 PM | #232 | |
boostalicious
|
Quote:
I would of thought you was setting that car up for alot of drag strip time with the cage and that kind of power. Noway you will ever get 2/3 of that power out on the street. I do think its cool to hear about though, which is why I will continue to follow your build to see where it goes.
__________________
*Powered by Maggie**553rwhp 541rwtq*
|
|
05-12-2011, 04:15 PM | #233 | |
Drives: 2011 Camaro SS2/LS3 Join Date: Feb 2011
Location: San Jose
Posts: 329
|
Quote:
Josh, why are you getting a cage put in if you aren't going to drag race it? I've never heard of that being a requirement for AutoX, though I'm definitely not an AutoX expert.
__________________
2011 Chevrolet Camaro SS2/LS3 - Pretty much bone stock (SLP SkipShift Eliminator, GTO clutch fluid reservoir mod) - 13.025 @ 110.492 MPH (12s?? )
1998 Pontiac Grand Prix GTP (retired) - Cam, exhaust, CAI, 12 PSI, tune - 13.465 @ 101.04 MPH |
|
05-12-2011, 04:20 PM | #234 | |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
Quote:
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
|
05-12-2011, 04:21 PM | #235 |
Drives: Black & Blue 1SS Join Date: Apr 2010
Location: Back In The Desert
Posts: 1,257
|
This thread makes me cry a little. !! I hate you all but love you all with a yearning passion
__________________
ARH 1 7/8 headers, ARH 3" XPIPE, MBRP 3" Catback |
05-12-2011, 04:22 PM | #236 |
need....more....hp
Drives: The Neighbor Hater Join Date: Dec 2010
Location: San Mateo, CA
Posts: 4,091
|
david i dont know what to do about rebuilding an engine! lol soooooo many factors to consider!
__________________
Mast Motorsports Built LS3 Stroker 418, IPS GT35R Twin Turbos, Exedy GTO4XD Twin Disc Clutch, Aeromotive A1000 Eliminator Stealth Fuel Pump, AEM Meth Injection, DSS 1400hp Axels, BC Coilovers, Pfadt & BMR Suspension, Hawk HPS Pads, Drilled/Slotted Rotors, Hurst Shifter, Custom Roll Cage by Blu808, T3 Ports, 22" Custom Concave Mesh Rims |
05-13-2011, 11:58 PM | #237 |
Drives: 2011 Camaro SS2/LS3 Join Date: Feb 2011
Location: San Jose
Posts: 329
|
Well, keep us posted on how the new build goes! Also, I might be interested learning to drift as well
__________________
2011 Chevrolet Camaro SS2/LS3 - Pretty much bone stock (SLP SkipShift Eliminator, GTO clutch fluid reservoir mod) - 13.025 @ 110.492 MPH (12s?? )
1998 Pontiac Grand Prix GTP (retired) - Cam, exhaust, CAI, 12 PSI, tune - 13.465 @ 101.04 MPH |
05-14-2011, 05:31 PM | #238 |
Drives: Camaro SS Join Date: Aug 2010
Location: kuwait
Posts: 554
|
more pix of the tail lights plz ? :P
__________________
_____________________________________________
mods : bb stripes , showstopper side markers , grill blackout , trunk blackout , interior AAC blue bulb , removed grill ss emblem , the bee-otch and disco ball ,concept diffuser , concept side mirrors. soon to come: taillights , maybe wheels , interior roof alcantra material . |
|
|
Tags |
carbon fiber intake, goldrush rally 4, the neighbor hater, tron camaro, twin turbo |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
3rd Gen Camaro Street Stock build thread (dialup beware) | zlathim | 3rd Generation Camaros | 9 | 12-06-2018 10:30 AM |
Tom Henry Racing THR22 2010/LS3/IBM/Supercharged SS Camaro [COTW 10/29/12] | GTAHVIT | Member Car Journals | 5217 | 06-27-2016 08:14 AM |
Do you want the Z28? | ChrisB | Camaro ZL1 Forum - ZL1 Specific Topics | 1616 | 09-04-2010 11:49 PM |
Anyone in St. Louis want a black SS March build Camaro | Sean_W | Camaro Price | Ordering | Tracking | Dealers Discussions | 11 | 03-08-2009 01:31 PM |