03-21-2013, 07:58 PM | #1 |
Tweety
Drives: 2010 Camaro 1LT RS Join Date: Dec 2012
Location: Fargo, ND
Posts: 246
|
Where to install LED's under the SEAT
I already have 9" LED tubes under the dash in the footwell but I would like to add another 9" tube under the SEATS just so it will be a little brighter. Any idea on how to mouth these? I'm using LEDGlow's Expendable Tubes. I'll attach a pic of where I want to mount them.
Again, it's a weird place to want to mount them but I want to try. I attached a picture of the passenger seat but I also want the drivers seat too. So is this possible?
__________________
Last edited by Tweiten; 03-21-2013 at 08:16 PM. |
03-21-2013, 08:08 PM | #2 |
Drives: 2013 2SS/1LE, 2004 Cavalier Join Date: Sep 2012
Location: jax, FL
Posts: 1,344
|
Judging from the pic, I'd try ziptied to that lower cross-bar. You should be able to ziptie tight enough for them to hold whatever angle gives you the amount of light you want.
|
03-21-2013, 08:15 PM | #3 |
Tweety
Drives: 2010 Camaro 1LT RS Join Date: Dec 2012
Location: Fargo, ND
Posts: 246
|
Your talking about that one on the WAY bottom almost touching the floor right? I'll try that when the LED ship to my house and see what happens. Thanks
__________________
|
03-22-2013, 01:14 AM | #4 |
Drives: 2013 2SS/1LE, 2004 Cavalier Join Date: Sep 2012
Location: jax, FL
Posts: 1,344
|
Yeah the bar that's got a tag hanging down in front of it. Seems to be the only place you have available for another strip.
Ziptie to that, then try to slack your wire to the center in case you want to move your seats (assuming you're going to route the wires under the panels there). Maybe also do a loose ziptie to hold the wiring off the seat rails for extra wire safety. Good luck! |
03-22-2013, 01:17 AM | #5 |
Drives: '11 SW 1LT RS Join Date: Aug 2012
Location: Granite Bay, CA
Posts: 717
|
Ya I have this exact same kit. Give us an update of how it goes! I also want to put some in the back but have no idea where to mount.
|
03-22-2013, 02:34 AM | #6 |
|
Interested to see how it looks.
__________________
2011 Camaro 2SS/RS, Circle D 3200, ADM Transmission Cooler, BTR Valvetrain, Cam Motion .621 .595 228/244 113+4, ARH 1 7/8 full exhaust, Cold Air Inductions, Katech C5R TC, Melling HV, BTR SLR lifters, Trunion Upgrade, LS2 Dampner, LS9 head gaskets, Bo White PTB, MM can, GFX, Subs, B&M Deep transmission pan,
Holley fuel rail, Proform valve covers, relocated coil packs |
03-22-2013, 09:17 AM | #7 |
Tweety
Drives: 2010 Camaro 1LT RS Join Date: Dec 2012
Location: Fargo, ND
Posts: 246
|
My lights just shipped today so I will let you guys know how it goes
When they get here.
__________________
|
03-22-2013, 09:51 AM | #8 |
Drives: 2010 Chevy Camaro 2SS RS Join Date: Jun 2011
Location: Columbus, Oh
Posts: 347
|
In for pix
|
|
|
Tags |
led, lights, underglow |
|
|