12-15-2012, 06:17 PM | #1 |
Drives: Currently 2016-2SS, Future ZL1/Z28 Join Date: Jul 2010
Location: Kansas
Posts: 978
|
My new door switch
Here I show this video of my new switches on the doors when I get back from the holidays I'll show how I did and what parts I used to use the stock panel-through connector
Tools required: T20, and T27 torx socket 7mm socket wrench Socket screwdriver Heat shrink tubing Electrical soldering iron Solder Heat gun Terminal crimper Phillips screwdriver Car Panel Removal Tool Electical Tape Precision Screwdrivers set Wire 3 color and black Parts you need: door panels 2012-13 (driver and passenger) door lock/unlock switch D.S#22879460,22847867. P.S#22847868 Conectors tyco (2) #1379029 (need a small mod) I have 1 sets with terminals available TE CONNECTIVITY Terminals Micro Quadlok Syste Series (8) 963715-1 and for Panel-through connectors, "if you want to use this way" you need : 1- Female HPCS FCI automotive Connectors #60013031 (1) 2- 1.5 Female Term FCI automotive Connectors #60000531 (2) 3- 2.8MM Male Term FCI automotive Connectors #60110631 (1) 4- 1.5MM SWS MALE FCI Automotive Connectors #60100731 (2) *these parts are hard to get, especially in small quantities* Step 1: I took the switch signal from radio/HVAC control or Body Control Module (X2 L-Blue connector). you can attach the t-tap to this wires. I prefer to solder the wires I would not do this if it was not permanent modification. door lock switch lock signal Pink/Black wire door lock switch unlock signal Orange/Black wire Step 2: make the connector. this is the switch diagram Step 3: must to pass the lock signal wire through the door connector. this thread can help http://www.camaro5.com/forums/showthread.php?t=155660 here we use the terminals for this connector if you want to use this mode or can pass the wire around of rubber boot body harness door harness on the door harness I changed the wire color. Please don't do that because it can be confusing Step 4: as had to pass two wires through the driver door connector. but only has one pin available, *I used the ABL wire (purple) for unlock signal and connect the LED (ABL) to the circuit LED backlight dimming (yellow) ABL with my wiring these are the steps that I took
__________________
Last edited by DWALEX; 03-13-2014 at 10:33 PM. |
12-15-2012, 06:23 PM | #2 |
Drives: 2 LT/RS YELLOW, AUTO., VIN NO. 602 Join Date: May 2010
Location: LAVAL (10 min. north of Montreal), CANADA
Posts: 3,526
|
Can't see the video, it's private?
__________________
T2 Facia, ACS TL1 Hood, ACS Winglets. G5CR CAI. Hotchsic Strut Brace and more...
|
12-15-2012, 06:31 PM | #3 |
Drives: 2011 RJT Camaro LT2 RS auto shift Join Date: Dec 2011
Location: Washington state
Posts: 1,861
|
It plays ok for me.
__________________
Caddy
|
12-15-2012, 06:32 PM | #4 | |
Drives: 2011 RJT Camaro LT2 RS auto shift Join Date: Dec 2011
Location: Washington state
Posts: 1,861
|
Quote:
__________________
Caddy
|
|
12-15-2012, 06:34 PM | #5 |
Drives: Currently 2016-2SS, Future ZL1/Z28 Join Date: Jul 2010
Location: Kansas
Posts: 978
|
__________________
|
12-15-2012, 06:48 PM | #6 |
Drives: 2011 RJT Camaro LT2 RS auto shift Join Date: Dec 2011
Location: Washington state
Posts: 1,861
|
That is to expensive for my blood. They are nice that you have in the door.
__________________
Caddy
|
12-15-2012, 07:12 PM | #7 |
Drives: Currently 2016-2SS, Future ZL1/Z28 Join Date: Jul 2010
Location: Kansas
Posts: 978
|
yes I know. I got a set of door panels from a totaled ZL1. I just changed the switch bezel
__________________
|
12-15-2012, 07:33 PM | #8 |
Drives: 2014 Z/28 #82+#192, 18ZLE 66Nova Join Date: Oct 2008
Location: By the lake in AZ
Posts: 15,719
|
good job let use now what you did.
|
12-15-2012, 07:51 PM | #9 |
Drives: Currently 2016-2SS, Future ZL1/Z28 Join Date: Jul 2010
Location: Kansas
Posts: 978
|
yes I will, I'm gonna make a schematic and load some pictures after holiday
__________________
|
12-15-2012, 08:35 PM | #10 |
|
Man where do you guys find these crashed camaros? I can't ever find newer cars at any of the junk yards around me!
|
08-05-2013, 02:26 PM | #11 | |
Drives: (sold) 2011 2LT/RS auto, SW/tan top Join Date: Jul 2011
Location: Driftwood, TX (Austin area)
Posts: 162
|
Quote:
Just another example of what Chevy should have done in the first place (put the power door lock switches on the armrests). My Jeep Wrangler has power window switches on the center console and power door lock switches on the doors. Whenever I switch vehicles, it takes a few tries to get reoriented! |
|
08-05-2013, 04:22 PM | #12 |
Drives: Currently 2016-2SS, Future ZL1/Z28 Join Date: Jul 2010
Location: Kansas
Posts: 978
|
I bought a pair of used panels just change the switch bezel and sold it again
__________________
|
12-26-2013, 08:24 PM | #13 |
Drives: 2014 Blue Ray Met. Camaro 1SS Vert Join Date: Feb 2012
Location: Indiana
Posts: 1,519
|
Thank you
|
12-27-2013, 06:33 PM | #14 |
Drives: 2014 Blue Ray Met. Camaro 1SS Vert Join Date: Feb 2012
Location: Indiana
Posts: 1,519
|
I bought some door panels months ago for the door inserts and put the door panels back in the box and left them alone till now. I was working on the RS lights today and decided to pull the door panels back out and look what I found. These must have been off of a 2013. So now I can do this mod and wait to do the Mylink upgrade. Yah
|
|
|
|
|