07-14-2010, 11:45 PM | #1 |
Tampa Gulf Coast Family
|
DIY LED Night Rider Scanner V2.0 install pics
pics
__________________
BALLSS2 the Wall! :5thgenvert:
|
07-14-2010, 11:46 PM | #2 |
Tampa Gulf Coast Family
|
__________________
BALLSS2 the Wall! :5thgenvert:
|
07-14-2010, 11:50 PM | #3 |
Tampa Gulf Coast Family
|
Hope this helps!
__________________
BALLSS2 the Wall! :5thgenvert:
|
07-15-2010, 12:21 AM | #4 |
Drives: '15 Z06, '01 NBM SS, '97 SS Join Date: May 2009
Location: Rio Rancho, NM
Posts: 12,170
|
Nice Pics!! What everyone was looking for I think.
Good job! Ivan |
07-15-2010, 03:10 AM | #5 |
What did u use to make the cuts
|
|
07-15-2010, 06:08 AM | #6 | |
Tampa Gulf Coast Family
|
Quote:
Btw I used my drill and bit the same width as the LED
__________________
BALLSS2 the Wall! :5thgenvert:
|
|
07-15-2010, 08:14 AM | #7 | |
Drives: C7 / ZL1 / SS / trucsk Join Date: Nov 2009
Location: G4 CLASSIFIED
Posts: 4,533
|
Quote:
Secondly, great HOW TO guide on the install!!! Nice ride as well!
__________________
2014 C7 Stingray 3LT/Z51
2013 Camaro SS 2012 Camaro ZL1 - 850 HP 2015 GMC Denali 3500HD 4x4 2012 GMC Sierra 3500HD 4x4 |
|
07-15-2010, 08:31 AM | #8 |
Tampa Gulf Coast Family
|
Oh ya no your right they never said it was a perfect fit... But it does fit pretty well and it is worth the money! Everyone likes it so I'm happy with that as well. Thanks for the props! I'm actually inspired mostly by your ride! YOU my friend have an awesome car! Thanks
__________________
BALLSS2 the Wall! :5thgenvert:
|
07-15-2010, 09:23 AM | #9 |
|
Thanks for the Great Write-up ROBBDOGG. I am off to the store to buy some 2-sided 3M Tape and then Wire them in and I will be done..
|
07-15-2010, 09:41 AM | #10 |
Tampa Gulf Coast Family
|
No problem! Thanks for the great product! Can u post your pics here as well please... Maybe there's something I missed that you could make easier...
__________________
BALLSS2 the Wall! :5thgenvert:
|
07-15-2010, 10:53 PM | #11 |
Drives: SW,SS1 RS,GRND EFFCS,ORNG STRPS Join Date: Mar 2010
Location: Los Angeles
Posts: 76
|
just what i was looking for!!! robbdogg! thank you thank you thank you!..where exactly did you connect the red wire? its kind of hard to tell on the pic.as well as the black wire. I just wanna make sure i do this right the first time, Im not mechanicaly gifted but what is a fuse connection and module?? go ahead and laugh guys!!
|
07-15-2010, 10:55 PM | #12 |
Drives: SW,SS1 RS,GRND EFFCS,ORNG STRPS Join Date: Mar 2010
Location: Los Angeles
Posts: 76
|
is the 3m tape placed just on the backside of the scanner or is it put on the top and bottom too???? "my scanner is useless sitting on my living room floor"
|
07-15-2010, 11:00 PM | #13 |
|
I wish somebody would make one that required no cutting, I am not cutting my Camaro.
__________________
Jannetty Racing JRE Street Package
|
07-15-2010, 11:14 PM | #14 |
Drives: SW,SS1 RS,GRND EFFCS,ORNG STRPS Join Date: Mar 2010
Location: Los Angeles
Posts: 76
|
its just little slits. how bad can it hurt??
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Need pics of Pedders Bushing install | jrpxxii | Suspension / Brakes / Chassis | 14 | 05-22-2012 12:58 PM |
DIY: SIDE GILL FADE AND OUTLINE INSTALL | Milk 1027 | Wiki | 2 | 09-08-2010 09:59 AM |
Roto-Fab CAI Install with Pics (5 Stars) | NVMY68SS | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 120 | 05-23-2010 01:51 AM |
Night Rider LED | cyberbro | Cosmetics and Lighting Modification Discussions | 14 | 04-24-2009 08:57 AM |