01-02-2010, 11:48 AM | #1 |
Drives: 2010 2ss Join Date: Aug 2009
Location: Georgia
Posts: 211
|
Glove box light
I use my glove box allot and wanted a light in it.
So when I got a Oracle LED light kit for Christmas & only changed the dome light I had a extra cool LED light. So I decided to do a glove box light mod. Other than the a little wire and a light bulb you only need 2 parts. A switch and a light socket. I used a door jam switch for a 94 Chevrolet truck & a marker light socket. Less then $10. @ Advance auto parts. The part numbers are s1067 for the switch and 8581608598 for the socket. My camera is crappy so forgive the bad pictures. The switch has 3 terminals but you only need the outside 2. ignore the one in the middle. You may can order a pigtail or get one out of a salvage yard but I just used 2 small spade connectors and some epoxy to hold them in the switch. Hot melt glue would also work. Wires for the switch Wires installed in switch Then I removed the glove box door and drilled a hole for the switch. (A 5/8 drill bit was just a hair to small. I used a box cutter to trim just a little more for the switch to fit). Above the glove box is a plastic cover that is held in by 5 torx head screws. 3 in the front along the opening of the glove box and one on each side close to the rear. At the rear on each side it has fittings that snap into place. After you remove the screws just give it a little pull and it will pop lose. Again with the 5/8 drill bit I drilled a hole for the light socket. The plastic is real soft so I warmed it up a little with a heat gun and pushed the light socket in. Once it cooled it locked in real tight. Here it is with the LED bulb installed I was going to run a separate wire to the fuse panel but after looking around there is a constant 12 volt power wire directly above the glove box. In the harness that runs above the glove box you can see 2 large red wires. One has a black stripe and is larger the other is just red. I spliced into the smaller one without the stripe. I am running it straight to the light socket so I am not really worried about it shorting out so I did not put a fuse on it. (A fuse would not hurt) I ran one wire from the switch to the light socket and the other I ran up and over the glove box with the factory harness to a ground on the other side. This is basically how I have it wired. Here it is without the glove box door Put the glove box door back on and it is good to go You have to lay in the floor and look up to see the bulb but it lights up the glove box Great and is up high enough I don't believe anything will ever contact it. Here you go. It is not that hard and makes it real nice finding stuff in the glove box at night Last edited by jbsrace1; 03-06-2010 at 04:19 PM. Reason: Corrected switch part number |
01-02-2010, 01:54 PM | #2 |
The Mark of Excellence
Drives: 2010 ABM 1SS RS LS3 Join Date: Jan 2009
Location: Smallest State in the Union
Posts: 8,690
|
Nice work, I believe there were some other members lamenting about the lack of a glove box light a while back. This will help.
__________________
BMR, CAI, DynoMax, Elite Eng., Hurst, Jannetty, Clear Image Headers & Hi Flow cats, Jet Hot, LSR, TSW, VMax, Vredestein |
01-02-2010, 02:20 PM | #3 |
Drives: VStar 1100 Classic, 2010 CGM 2SS/RS Join Date: Mar 2009
Location: GMT -10hrs
Posts: 405
|
Very good DIY instructions!
__________________
|
01-02-2010, 03:41 PM | #4 |
Heartless-1
Drives: 2008 nissan altima coupe Join Date: Nov 2008
Location: Los Angeles
Posts: 93
|
awesome work, i need a light in there also
__________________
"When A Man Gains The World, What Good Is His Profit If He Loses His Soul?" |
01-03-2010, 06:23 PM | #5 |
Drives: Rally Yellow 2SS/RS Join Date: Apr 2009
Location: Wellington FL
Posts: 1,597
|
any pics at night so we can see it in action?
__________________
#52325 Delivered 11/07/2009 |
01-03-2010, 08:42 PM | #6 |
Drives: 2010 2ss Join Date: Aug 2009
Location: Georgia
Posts: 211
|
|
01-03-2010, 08:54 PM | #7 |
|
Very helpful mod, I do think this will be going into my Camaro
__________________
CAI intake | OBX LT Headers | Flowmaster AT Exhaust | Trifecta Tune | SS Rear Diff, Axles & Driveshaft Zex 100 Shot Nitrous | Konig Airstrike Wheels | Custom Engine Cover, Fuse Box & Underhood Bowtie Eibach Springs & SS Sway Bars | BMR Strut Brace | Drake Shifter | Vitesse Paddles | 13.26 @ 105.88 mph |
01-03-2010, 08:55 PM | #8 |
Drives: VStar 1100 Classic, 2010 CGM 2SS/RS Join Date: Mar 2009
Location: GMT -10hrs
Posts: 405
|
Wow! Very bright.
__________________
|
01-03-2010, 09:21 PM | #9 |
Layla
Drives: '10 2SS/RS, LS3, CGM/IO Join Date: Dec 2009
Location: Newport, RI
Posts: 345
|
great mod, love it. so you don't know what the power source is for the wire you tapped into? Or where it leads?
|
01-03-2010, 09:44 PM | #10 |
Whipped
|
nice... good job.
__________________
|
01-03-2010, 11:21 PM | #11 |
Drives: 92 firebird,2010 camaro Join Date: May 2009
Location: Indianapolis,In
Posts: 362
|
MY CONCERN WAS NO LIGHT IN THE ENGINE AREA.WAS SHOWING THE CAR TO FRIENDS AT NIGHT AND THEY WANTED TO SEE THE ENGINE,OPENED THE HOOD AND NO LIGHT.WISH THEY COULD HAVE PUT ONE THERE.
|
01-04-2010, 06:28 AM | #12 |
Drives: 2010 2ss Join Date: Aug 2009
Location: Georgia
Posts: 211
|
I believe it to be the power feed for the blower speed control but it was getting cold and I did not take the time to trace it out. The LED pulls such a small load I wasn't worried about it. If I get some time this afternoon I will try and see exactly what it feeds.
|
01-04-2010, 06:37 AM | #13 |
Retired Army, 101st ABN
|
I am sold! I like it and will add it to my "To Do" list! Thanks!
__________________
"BABY" is a Summit White, 2SS/RS, My Tribute to the 13 years I served in the 101st Airborne Division!!!
ORDERED: 18 JUL 09 #NMMS88, BORN ON 4 NOV 09 at 12:26pm VIN:63460~ HOME on 18 NOV 09! "101BABY" |
01-04-2010, 06:46 AM | #14 |
Drives: 2010 2ss Join Date: Aug 2009
Location: Georgia
Posts: 211
|
There are all kinds of under hood light kits around. Or you can go to any salvage yard and pick about any 80 or 90's chevrolet truck and get one that only requires running a power wire to it.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
DIY - Footwell LED lighting In tune with Dome Light | markmass | Camaro DIY & HOW-TO instructions & discussions | 52 | 09-03-2010 08:00 PM |
NO fog light switch..... | strobi | Exterior Parts & Accessories | 16 | 12-16-2009 05:27 PM |
no light in the glove box | Chris-10 | 5th Gen Camaro SS LS LT General Discussions | 43 | 11-22-2009 01:24 PM |
Anyone have their engine light come on and stay on...Advice please (Pic) | DCJ | Camaro Issues / Problems | Warranty Discussions | TSB and Recalls | 38 | 09-07-2009 05:26 PM |
New 4.5 L Duramax Diesel V8 for light duty pickups | Scotsman | General Automotive + Other Cars Discussion | 8 | 12-01-2008 06:21 PM |