03-27-2011, 07:27 PM | #1 |
Drives: 2010 CGM 1SS Camaro Join Date: Oct 2009
Location: The Woodlands, TX
Posts: 527
|
HELP! ... Lost a cap in engine bay!
HELP!! lol.
So i was in the engine bay and was cleaning up everything and noticed the brake reservior was a leaking a bit it seamed so i took the cap off to clean everything up. Cleaned off the cap and put on the side of engine bay where the hood seals. cleaned up the reservor body and put the towel on the side of car (i know not smart.) Problem comes is i put the towel on the cap so when i picked up the towel it SLID DOWN INTO THE ENGINE BAY! Straight down behind the strut tower and into the only hole it fits in ... pics below of location im talking about ... the hole under the AAC2 sticker ...anyway to get it out?!?!?!!!!!!!! tried reaching down into there and found out to things ... 1) its hot in there after driving around. and 2) my hands to big :( alternate way to retrieve it?
__________________
|
03-27-2011, 07:56 PM | #2 |
Drives: S/C 2SS/RS Camaro-6M-VicRed Join Date: Aug 2009
Location: Alfie (Mariano) lives in Shelby Twp, Metro-Detroit
Posts: 1,119
|
I can't tell from the photo, but if you can see it, even if you can't, perhaps you can use one of those "reach tools". You'll need the "claw" type as shown, not a grabber type. I have a couple of these things and they have saved me from a lot of grief more than once. Good luck.
Alfie
__________________
|
03-27-2011, 08:02 PM | #3 |
Drives: 2010 CGM 1SS Camaro Join Date: Oct 2009
Location: The Woodlands, TX
Posts: 527
|
cant see it, cant feel it, dont know how far it went ... theres a hole in the hole (if that makes sense)
__________________
|
03-27-2011, 09:10 PM | #4 |
Proud owner of Litho #195
Drives: 2011 CGM 2LT/RS Join Date: Sep 2010
Location: Oklahoma
Posts: 2,551
|
Get like a dowl rod with some duct tape on the end and it will stick to it and pull it up, or even a bent metal hanger.
__________________
Mods:http://www.camaro5.com/forums/showthread.php?p=3139029#post3139029
Team LLT Social Group Link:http://www.camaro5.com/forums/group.php?groupid=256 |
03-27-2011, 09:13 PM | #5 |
Account Suspended
Drives: 89 IROC 350 Join Date: Mar 2009
Location: Back roads, southern Ohio
Posts: 12,504
|
Go get a new one... its gone. I see where it fell and its in that area that you'll spend too much time trying to fish it out. Call the dealer tomorrow.
There is a TSB about them leaking so you need a new one anyhow. I noticed you said you were wiping off the resivior bc is was leaking... it shouldn't be. Time for a trip to the dealer. They should have them in stock as its a commonly replaced item. |
03-27-2011, 09:18 PM | #6 |
Drives: 2011 Camaro 1SS/M6 Cyber Gray Met. Join Date: Jan 2011
Location: Navarre, FL/Emerald Coast
Posts: 624
|
Yeah I'd suggest a pair of mechanical fingers to fish around in there. Bet you won't do that again!
__________________
2011 1SS/LS3 M6--Vararam CAI-Corsa catback-Dynatech LTs-RX Catch Can-Vmax ported TB-Eibach Springs-Night Fury Camshaft- 486RWHP/458 TQ
|
03-28-2011, 08:52 AM | #7 |
|
You're going to need a new cap anyway since it sounds like you have (had) one of the leaky caps. I did too, and got a new cap under warranty (but it can't cost too much). No leaks with the new cap.
__________________
Black 2SS ordered 1/4/2010, received 2/19/2010
|
03-28-2011, 09:01 AM | #8 |
Drives: 2010 2SS/RS IBM Black Polished Join Date: Feb 2009
Location: Colorado
Posts: 2,108
|
I had a similar situation with a bolt. Took off the front tire and the wheel trim liner. Was then able to manipulate it back up thru the hole. Good luck man...
__________________
418 Stroker, 621RWHP 648 lbs TORQUE Built by Laramie GM Auto Center Tuned by Nick at Mac Autosport. EForce SC, 2 3/4pulley,LPE dual fuel pump, JRE Twin fuel rail upgrade, posi clutch kit, RX oilcatch can and breather, Callies Compstar crankshaft and rods, Racing bearings, CP -13.8 race pistons, steel rings, Comp Cams X6 blower cam, Springs, HD timing chain and tensioner, Doug Thorley Tri Y LT headers, 89.7lb injectors, RPM rollbar, DSS1400 shafts, Simpson 5 pt harness, BMR Toe rods and trailing arms, led lights, RPM input and output shafts
|
03-28-2011, 09:14 AM | #9 |
Drives: 2017 Camaro 2SS - M6, NPP, MRC Join Date: Jan 2010
Location: Delco, PA
Posts: 971
|
I lost the cap to a liter of oil through the hole for the hood release once, down into the sealed front fascia. Let me tell you what a joy that was, especially squeezing my not-small hand through a hole in the fascia and then having to pull it out again with the cap. I'm surprised I had any skin left after that one - as it was I had my hand glazed with neosporin and wrapped in gauze for a couple days afterwards, but I got that cap out!
|
03-28-2011, 09:23 AM | #10 |
Drives: 2010 2SS/RS M6 Black/Black Join Date: Apr 2009
Location: Pittsburgh, PA
Posts: 1,281
|
A few things to note if you are going to get a new cap...
ONE: ( you probably know this) dont drive it with the cap off TWO: put something over the reservoir for now to keep junk and moisture from getting in there
__________________
Pittsburgh Automotive Photography Black on Black 2SS/RS w/ white stripes Dynomax 3" Bullet Catback, CAI Cold Air Intake |
03-28-2011, 09:36 AM | #11 |
Drives: 2010 Camaro SS LS3 Join Date: Sep 2010
Location: Eastern MO
Posts: 3,786
|
http://www.amazon.com/gp/product/B00...G0BAD6Q9EKADBH
One of these ^^^ to see if you can spot it and then a bendable wire with duct tape to retrieve.
__________________
She is only memory now. |
03-28-2011, 02:35 PM | #12 |
Drives: 2000 Z28. 2010 1SS IMB. Join Date: Aug 2009
Location: New Mexico
Posts: 1,081
|
a blow torch and a cutting wheel should get it out.
__________________
1990 RS = First Car -SOLD
2000 Z28 = SOLD 2010 1SS/RS = Mysstique Whipple Supercharger Dyno= 618hp 555tq at the wheels IMB Silver Stripes VIN#44025 Born: 9/9/09 Delivered: 9/28/09 |
03-28-2011, 06:59 PM | #13 |
Madman
|
I dropped a bolt in that hole...took loose inner fenderwell and retrieved it..only way to do it...... even tried claw..& magnet..NO GO
|
03-28-2011, 07:06 PM | #14 |
Drives: 2013 AGM 1SS/RS 1LE Join Date: Jul 2010
Location: jacksonville
Posts: 248
|
wire coat hanger
__________________
2013 Ashen Grey Metallic 1SS/1LE, NPP, Camera
(1 of 43 produced) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Acronyms? | KEEP RT | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 20 | 03-11-2011 08:57 PM |
Over 230 Satisfied 2010 Camaro Customers! Paddock Chevrolet has 40 in stock NOW | camarojoe | Dealer Camaros for Sale | 2 | 05-24-2010 05:58 PM |
Pfadt Race Engineering releases new Camaro V8 Engine Mounts | PfadtRacing | Suspension / Brakes / Chassis | 6 | 01-15-2010 12:58 PM |
AirAid Cold Air Intake anyone? | FLYNNZL1 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 12 | 01-01-2010 09:05 PM |
Axial Vector Engine | Mr. Wyndham | General Automotive + Other Cars Discussion | 6 | 06-20-2007 04:00 PM |