05-17-2013, 11:15 AM | #1 |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Finally - evap ready
Finally, after two months, three weeks, 4 tanks of 93 octane the evap readiness is set. On the way to get the sticker, new tags and then can get back to tuning. !!
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
05-17-2013, 11:27 AM | #3 | |
Drives: 16 Camaro SS, 15 Colorado Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 13,943
|
Quote:
Now lets see what you can get out of that cammed beast.
__________________
2016 Camaro 1SS - 8-speed - NPP - Black bowties
2010 Camaro 1LT V6 (Sold. I will miss her!) |
|
05-17-2013, 11:38 AM | #4 |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Yes sir! It's been a bit of a delay - but in the end will be worth the time to make it right.
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
05-17-2013, 12:45 PM | #5 |
Emerald Coast Camaros
Drives: 2010 Camaro 2LT/RS M6 Join Date: Nov 2009
Location: Tallahassee FL
Posts: 9,687
|
My Evap isnt even ready and I am not tuned. It's a good thing Florida doesn't do these checks because if they did i would be screwed
What did you have to do to get them to say ready? |
05-17-2013, 02:16 PM | #6 |
COTW 9/16/13
Drives: 2011 2LT/RS Camaro IOM Join Date: Jan 2012
Location: Syracuse
Posts: 10,089
|
There is some procedure that GM has that you could follow, or you can just keep driving till it is ready haha. Let me see if I can find the thread from awhile go that talked about it.
|
05-17-2013, 02:18 PM | #7 |
COTW 9/16/13
Drives: 2011 2LT/RS Camaro IOM Join Date: Jan 2012
Location: Syracuse
Posts: 10,089
|
Found it menendez, post 5 and 6 tell you how to do the GM procedure.
http://www.camaro5.com/forums/showth...ight=emissions |
05-17-2013, 04:23 PM | #8 |
Drives: 2013 Mustang 5.0 Join Date: Dec 2012
Location: Houston
Posts: 1,788
|
mine is still not ready and i havent even done headers?
__________________
Performance Mods: Vararam Intake, MRTv2.0 exhaust, Elite Engineering CC, Vmax Black Iceolator, Vmax Ported TB, OBX LT Headers w/ no CATS, LMR Tune
Visual mods: Eagle Eyes w/5k hids, Custom Hood Spears, Heritage Grille, Stage 2 LED Dome lights,Transformer Emblems, PD Bezels, 19in Chevy rims with pirellis, Blue painted calipers, GM GFX Front Splitter, 35/20 % Tint, TailLight Tint(charcoal) 1/4 Mile: 13.65 sec @ 102.53 mph R.I.P. |
05-17-2013, 09:39 PM | #9 |
|
Yellow Glide great to hear from you, I was just wondering what was going on with your cams the other day! I'm anxious to hear how this works out for you!
|
05-17-2013, 09:59 PM | #10 |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
I tried doing the GM procedure but had issue with getting to a remote area I could do the test. I do know it was approximately 150 miles to get the sensor ready. I firmly believe the key to getting the sensor ready is performing a sufficient number of cold starts and short trips under 60mph.
As I said, I tried to do the GM procedure but never had the DIC indicate to accelerate during the test. I attempted the GM test four times without success, then I had the wife do short trips and stay under 60.
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
05-17-2013, 10:07 PM | #11 | |
Drives: 2011 1LT "Chakita". 04 Yota Join Date: Jun 2011
Location: Round Rock, TX
Posts: 823
|
Quote:
Car is fun to drive - need more traction though. Stand on it about 20mph in first and it spins with the nannies on. With TC off might as well pour bleach on the ground and roll thru it. Burnt rubber really stinks up the inside of a car - I've started buying the little pine trees by the case.
__________________
Hi, my name is Chakita. I have cams!!!!
Build thread: http://www.camaro5.com/forums/showthread.php?p=3847083 |
|
05-18-2013, 07:03 AM | #12 |
My Dream Car
Drives: 2011 SIM LS3 1SS Join Date: Jul 2009
Location: staten island
Posts: 1,534
|
Congrats I know it takes a while and try's the patience
__________________
CAI intake/ADM Scoop/Stainless Power Headers/Dynatech cat back exhaust/Vitesse Throttle Control/ Ported Throttle Body/QTP Electric Cutouts/ 3.91 gears and janetty rear posi/ Tuned by Janetty racing
|
05-18-2013, 08:22 AM | #13 |
|
Sounds familiar, took me that long a couple years ago to get ready too. Now I just don't touch the tune during the spring until the damn inspection is done.
__________________
Formerly owner of:
2012 2SS/RS Build Thread - Totaled by red light runner 2010 LT/RS Build Thread - Traded in for 2012 2SS 2007 Acura TSX 1992 Oldsmobile Achieva V6 1992 Mercury Sable |
05-18-2013, 08:50 AM | #14 |
Don't Sleep on My V6
|
This is great Yellow. Cant wait to hear from you and the cams.
Sent from my Samsung Galaxy S III
__________________
|
|
|
|
|