05-23-2012, 09:25 PM | #85 |
Fast Cars and Old Guitars
Drives: 2015 2SS RS (L99, baby!) Join Date: Apr 2012
Location: N. CA
Posts: 3,974
|
I see this is an old thread. I've been into drivelines my whole career. NO! Bearings are not splined. Feel free to chat on DLs!
|
05-23-2012, 10:58 PM | #86 |
Booooosted.
|
Why are they only pressed?
|
06-06-2013, 06:43 PM | #87 |
Drives: 2011 2SS/RS SGM Join Date: May 2010
Location: uniontown,PA
Posts: 787
|
i just found this thread.
i had the same exact thing happen on my car, what a few people on here said to look for was the driveshaft bolts, but it ended up being this bearing. made the most horrible clunking noise anytime it was rolling, its in the chevy garage as we speak getting fixed should have it tomorrow or monday. im freakin out without it,but at least ill be able to drive it normally
__________________
---2011 synergy green 2SS/RS---
09/27/2010 - (3800) 10/01/2010 - (4200) 10/09/2010 - (4800) Vehicle on final destination route 10/19/2010 - (5000) delivered to dealer 11/19/2010 - (6000) delivered to customer |
05-20-2014, 07:08 PM | #88 |
Ok.. Bring this thread back from the dead. My car is making a loud vibrating noise in the area of this bearing from 40mph on up and on acceleration. I got under the car and the only thing I can find that has any slack is it. It's not a lot just maybe 1/16-1/8 if that.
I can't find it on any gm parts websites. Anyone know where to get one? I am v6 auto btw. Hope this doesn't cost both arms and a leg |
|
05-20-2014, 11:54 PM | #89 | |
Booooosted.
|
Quote:
Does not mean that it isn't the bearing anyway but it does have about that much movement when pushed and pulled from underneath. As far as a fix, if you're handy then you can do it probably for under a hundred dollars. I got a free driveshaft from a forum friend who had put a solid shaft in. |
|
05-21-2014, 07:48 AM | #90 |
Senior Camaro Fanatic
Drives: 2011 SS/RS manual - White Join Date: Aug 2010
Location: aiken, sc
Posts: 1,980
|
As an aside, I have posted long ago about a chirping noise coming from my car and subscribed to this thread to follow. It only happens in hot weather when the car has just been started. There is a TSB about this bearing "floating" on some vehicles.
Three and a half years later, I still have that noise, with no real issue coming up. I still think it's that bearing turning and stopping causing the chirp... but it has yet to wear enough to become a vibration.
__________________
Former '68 and '69 Z/28 Owner...........Now sporting around in a 2011 RS/SS with........Kooks LT's and cats, JRE tune, CAI, scoop, ZL1 Bumper conversion, custom ZL-1 grille, halo harness, Painted silver stripes, GM GFX, black painted lower edge of skirts and rear bumper. MGW shifter.....and now a 3.91 1LE diff
Last edited by f5journal; 05-21-2014 at 09:01 AM. |
05-21-2014, 09:00 AM | #91 | |
Quote:
I called the dealership and they said it would be covered so that's a plus. |
||
11-07-2016, 11:54 AM | #92 |
RunEmIfYouGotEm
Drives: She wears midnight blue ls3 m6 Join Date: Jan 2016
Location: Chicago
Posts: 84
|
I might have same issue,is this a m6 did this bearing process fix issues
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TR6060 hydraulic bearing kit Fits 10-up Camaro | Xplosive Performance | Transmission / Driveline | 5 | 05-21-2012 10:59 PM |
FS. Brand New Camaro SS Two Piece Driveshaft with Center Bearing | 55Designs | Transmission / Driveline | 4 | 12-08-2010 06:33 PM |
Ball Bearing | Blkcamaro757 | Forced Induction - V8 | 9 | 07-29-2010 03:08 PM |
2010 Camaro BMR Driveshaft Safety Loop pics!!! | BMR Sales | Dragstrip and Launch Techniques Discussion | 29 | 12-12-2009 11:45 PM |
2010 Camaro BMR Driveshaft Safety Loop Pics!!! | BMR Sales | Wheels and Tires Talk Sponsored by The Tire Rack | 3 | 10-20-2009 11:21 PM |