11-13-2015, 07:06 AM | #547 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
|
11-13-2015, 08:42 AM | #548 |
Drives: 2010 2SS/RS Join Date: Dec 2009
Location: Clarksville Tennesse.
Posts: 6,059
|
How do you get the light to shine through dash pieces?? Are you still required to sand them down a little bit??
|
11-13-2015, 08:55 AM | #549 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
If you don't want to sand, you can create a gap for the light to come through. That is what most do.
|
11-13-2015, 05:59 PM | #550 |
Drives: 2010 camaro Join Date: Nov 2015
Location: ottawa
Posts: 12
|
do you know of any dealer in Canada. I would like to buy from you but shipping is more than the pipe....
|
11-13-2015, 06:03 PM | #551 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
I have shipped regular mail before and it was a lower cost than the default Priority.
|
11-14-2015, 07:40 AM | #552 |
Drives: 2010 camaro Join Date: Nov 2015
Location: ottawa
Posts: 12
|
ok I am new at this forum thing so if you can message me how you would like m to proceed. tx
|
11-26-2015, 08:25 AM | #553 |
Drives: 2011 Camaro SS/RS Convertible Join Date: Jun 2015
Location: Columbus
Posts: 444
|
I have a 2ss - if I buy your "dash kit" in the ice blue is there anything I need to do the dash pieces (sand or anything) for the light to show through? It looks like they were made for the light tubes stock.
__________________
2011 Camaro SS/RS Vert - Jewel Red Tintcoat, 6M, 231/247 Comp Cam, Kooks headers, Borla ATAK, ATI under drive pulley, Richmond 4.10s, LS9 clutch, Hurst shifter, BMR Springs |
11-26-2015, 09:01 AM | #554 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
No sanding if you don't want to. These are for the gap-method where you keep the panels a bit proud of the dash so that there is a slight gap left for the light to come through.
|
02-15-2016, 03:15 PM | #555 |
Trust No One!
Drives: 2010 SIM 2LT/RS Join Date: Oct 2014
Location: NOLA
Posts: 531
|
|
03-04-2016, 10:14 PM | #556 |
Drives: 2014 ZL1 Join Date: Aug 2015
Location: Tucson AZ
Posts: 217
|
The dash kit is listed as a no drill size. Does it light up the panel fully since it is not drilled to run from end to end?
|
07-18-2017, 07:01 AM | #557 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
Missed this. Always best to email questions.
Obviously, there will not be light on the very end where the LEDs are. You can keep it down to about 3/8", though. We just felt that most would not want to drill into their dash and risk damaging it. |
02-27-2018, 07:02 AM | #558 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
Bump for these pipes! I don't think all Camaros have them yet.
|
02-27-2018, 10:16 AM | #559 |
Instagram: Sangstah
|
your links do not work per the original post
__________________
2019 SS 1LE - "CaSSandra" 2014 SS - "AleSSandra - Sold" 94 Z28 - Sold
Follow the build https://www.camaro6.com/forums/showthread.php?t=612717 |
02-27-2018, 12:40 PM | #560 |
Drives: '16 2SS Join Date: Apr 2011
Location: Chicago Suburbs
Posts: 2,271
|
Thanks for that. Investigating.
|
|
|
Thread Tools | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Who is up for an install day for the dash ABL? (Updated) | 2010SSRSM6 | USA - California | 565 | 07-10-2012 08:41 PM |
Jba catted mud pipes....check engine light on? | Camarowguy | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 13 | 07-23-2011 08:35 AM |
WTB: ABL Light Pipe 2058296-1 Tyco | irocnroll | Interior Parts & Accessories | 13 | 05-20-2011 08:20 PM |
Those with LT's, RESET your check engine light! | TAG UR IT | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 107 | 08-18-2010 01:51 AM |
ABL lighting and Footwell Light Install? | JProberts | USA - Mid-Atlantic | 3 | 02-25-2010 10:17 PM |