Chevy Laser Imaged Courtesy Door Lights Installed - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

bee sting · 06-12-2012, 05:02 PM

Just wanted to post a few pics of the Chevy Bowtie Courtesy Door Lights I installed yesterday . Wasn't hard at all but you do have to make sure where your drilling . Not much for clearance inside the door it's self but where I placed mine it was fine . I have some measurements if anyone is interested .

The night pics I took don't do these lights justice.. I'll try to retake them when I have the car out the garage . The Bowtie is Very detailed and looks just like the one on our Camaro .

I got these from Andrew6 when he was doing his group buy last week . Andrew has been nothing but helpful answering all my questions that I had with this install . Here is the link http://www.camaro5.com/forums/showthread.php?t=220328

LoPerformance Motorsports · 06-12-2012, 05:25 PM

What wire did you tie into to get the light to work when you open the door?

LoPerformance Motorsports · 06-12-2012, 05:27 PM

had my door panels off this week to install new speaker and looked to me that they could mount in the door panel itself with plenty room. Dont know the lenghts of the lights, maybe 3" or so.

eklypised · 06-12-2012, 06:20 PM

Looks pretty cool...can you get any other design other than that?

bee sting · 06-12-2012, 06:58 PM

Quote:

Originally Posted by LoPerformance Motorsports

What wire did you tie into to get the light to work when you open the door?

I tied it into the ABL wires but I may go back and have it wired to have 12 volts all the time . Right now it just comes on when door is open for maybe 15 seconds or when the light switch is turned on.

Quote:

Originally Posted by eklypised

Looks pretty cool...can you get any other design other than that?

Yes he is working on a few New designs as we speak .

gml1998 · 06-12-2012, 09:07 PM

Quote:

Originally Posted by LoPerformance Motorsports

had my door panels off this week to install new speaker and looked to me that they could mount in the door panel itself with plenty room. Dont know the lenghts of the lights, maybe 3" or so.

I put mine in the door panel ,had no trouble . I did have to trim some of the styrofoam insulator.
I wired mine into the abl lights and put a small switch in the door panel pockets to turn them off, otherwise they would be on anytime the abl lights are on.

bee sting · 06-13-2012, 04:48 AM

Quote:

Originally Posted by gml1998

I put mine in the door panel ,had no trouble . I did have to trim some of the styrofoam insulator.
I wired mine into the abl lights and put a small switch in the door panel pockets to turn them off, otherwise they would be on anytime the abl lights are on.

That's not a bad idea .. I never thought about the door panel but to late for me now lol

. Post a pic if you took any .

sub zero · 06-13-2012, 06:18 AM

it's cool

rberns · 06-14-2012, 05:39 AM

I am waiting for something different other than the bowtie and cheverolet wording. Hoping that something comes out with an SS or Camaro on it instead.

bee sting · 06-14-2012, 03:05 PM

I know it's in the works , I plan on taking these out myself and replacing them with something Camaro related when they're released.

Mach · 06-14-2012, 09:59 PM

Cool as hell!!! Nice Work!

http://www.camaro5.com/forums/showthread.php?t=230649

skinman · 06-16-2012, 11:14 PM

That's different AND pretty sharp!

pierre777 · 06-17-2012, 12:17 AM

Niiiiiice does it come with other designed projections.

bee sting · 06-20-2012, 03:12 PM

Yes in the next few weeks there will be Camaro and maybe SS & RS In the works .

06-12-2012, 05:02 PM	#1
bee sting Drives: 1997 30th Ann. Z28 & 2010 2LT RS Join Date: Jan 2010 Location: Suffolk Virginia Posts: 1,933 View My Garage	Chevy Laser Imaged Courtesy Door Lights Installed Just wanted to post a few pics of the Chevy Bowtie Courtesy Door Lights I installed yesterday . Wasn't hard at all but you do have to make sure where your drilling . Not much for clearance inside the door it's self but where I placed mine it was fine . I have some measurements if anyone is interested . The night pics I took don't do these lights justice.. I'll try to retake them when I have the car out the garage . The Bowtie is Very detailed and looks just like the one on our Camaro . I got these from Andrew6 when he was doing his group buy last week . Andrew has been nothing but helpful answering all my questions that I had with this install . Here is the link http://www.camaro5.com/forums/showthread.php?t=220328 Attached Images __________________

06-12-2012, 05:25 PM	#2
LoPerformance Motorsports Loperformance Motorsports Drives: 2011 2LT Join Date: May 2011 Location: Atlanta,Texas Posts: 231	What wire did you tie into to get the light to work when you open the door? __________________

06-12-2012, 05:27 PM	#3
LoPerformance Motorsports Loperformance Motorsports Drives: 2011 2LT Join Date: May 2011 Location: Atlanta,Texas Posts: 231	had my door panels off this week to install new speaker and looked to me that they could mount in the door panel itself with plenty room. Dont know the lenghts of the lights, maybe 3" or so. __________________

06-13-2012, 06:18 AM	#8
sub zero Drives: RED@2SS Join Date: Aug 2010 Location: UAE Posts: 1,372	it's cool __________________

06-14-2012, 05:39 AM	#9
rberns Drives: 2011 Camaro 2SS/RS Join Date: Apr 2011 Location: US Posts: 3,291 View My Garage	I am waiting for something different other than the bowtie and cheverolet wording. Hoping that something comes out with an SS or Camaro on it instead. __________________ 2011 Camaro 2SS/RS, Circle D 3200, ADM Transmission Cooler, BTR Valvetrain, Cam Motion .621 .595 228/244 113+4, ARH 1 7/8 full exhaust, Cold Air Inductions, Katech C5R TC, Melling HV, BTR SLR lifters, Trunion Upgrade, LS2 Dampner, LS9 head gaskets, Bo White PTB, MM can, GFX, Subs, B&M Deep transmission pan, Holley fuel rail, Proform valve covers, relocated coil packs

06-12-2012, 06:20 PM	#4
eklypised Account Suspended Drives: 2010 Camaro 2SS \| Indy Pace Car Join Date: Apr 2010 Location: South Carolina Posts: 258	Looks pretty cool...can you get any other design other than that?

06-14-2012, 03:05 PM	#10
bee sting Drives: 1997 30th Ann. Z28 & 2010 2LT RS Join Date: Jan 2010 Location: Suffolk Virginia Posts: 1,933 View My Garage	I know it's in the works , I plan on taking these out myself and replacing them with something Camaro related when they're released. __________________

06-14-2012, 09:59 PM	#11
Mach Drives: White M6 1LT RS Join Date: Mar 2010 Location: Canton, MI Posts: 1,676	Cool as hell!!! Nice Work! http://www.camaro5.com/forums/showthread.php?t=230649 __________________ Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End Next mod: Done!

06-16-2012, 11:14 PM	#12
skinman Drives: Convertible Camaro Join Date: Mar 2011 Location: Louisiana Posts: 858 View My Garage	That's different AND pretty sharp! __________________

06-17-2012, 12:17 AM	#13
pierre777 HT5 COTW 9/3/2012 Drives: Cyber Bullet Join Date: Jun 2011 Location: lebanon Posts: 4,555 View My Garage	Niiiiiice does it come with other designed projections. __________________

06-20-2012, 03:12 PM	#14
bee sting Drives: 1997 30th Ann. Z28 & 2010 2LT RS Join Date: Jan 2010 Location: Suffolk Virginia Posts: 1,933 View My Garage	Yes in the next few weeks there will be Camaro and maybe SS & RS In the works . __________________