Stock Height Measurement - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

LH17 · 12-18-2009, 10:01 AM

Sometime, if one of you guys have a minute, could I get a measurement of the wheel opening to ground on an SS with stock suspension?

*CamaroSpike23* · 12-18-2009, 10:29 AM

http://www.camaro5.com/forums/wiki.p...ERIOR_PHYSICAL

around 31" is the best I can do at the moment.

Bruce@raymondsperformance · 12-18-2009, 12:36 PM

My 2ss camaro was 30.5" front and rear stock

LH17 · 12-19-2009, 06:57 AM

Thanks!

Ltdodge · 12-19-2009, 10:20 AM

with my pfadt lowering springs I am at 28-5/8" front and 28-7/8" rear

mdinferno · 02-28-2010, 07:04 PM

Does this mean the springs on the RS is the same height as the SS.

Info@PeddersUSA.com · 02-28-2010, 10:01 PM

We have measured a lot of SS Camaros and have found as much as a 1/2 variation from one to another, especially in the back. it is very common to see 5 to 8mm variations side to side in the fronts.

mike
dms

2010SLVRBULIT · 02-28-2010, 10:30 PM

Quote:

Originally Posted by mdinferno

Does this mean the springs on the RS is the same height as the SS.

stock 4 stock, pretty sure RS sits higher than the SS(suspension, weight, etc)..

mdinferno · 03-02-2010, 04:03 PM

I just measured my RS from the ground to fender F: 30 1/4" R: 30 1/2". Any other RS owners can confirm these numbers.

clg_98ta · 03-02-2010, 06:35 PM

Quote:

Originally Posted by 2010SLVRBULIT

stock 4 stock, pretty sure RS sits higher than the SS(suspension, weight, etc)..

The RS package should not affect the car height.

BTW, My stock non-RS SS measures a tad over 30" front and rear.

12-18-2009, 10:01 AM	#1
LH17 Drives: 2010 Camaro SS Join Date: Apr 2009 Location: South Carolina Posts: 50	Stock Height Measurement Sometime, if one of you guys have a minute, could I get a measurement of the wheel opening to ground on an SS with stock suspension? Attached Images

12-19-2009, 10:20 AM	#5
Ltdodge Drives: 2008 Z06 Join Date: Apr 2009 Location: Oviedo, Florida Posts: 891	with my pfadt lowering springs I am at 28-5/8" front and 28-7/8" rear __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY Noweeds exhaust diverter installation	CanadianCamaro	Camaro DIY & HOW-TO instructions & discussions	42	08-15-2016 11:11 AM
Camaro L99 American Racing Headers (Catted) system with stock exhaust = +42rwhp	pharmd	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	43	07-25-2009 10:01 AM
Check your Order here	bvonscott	Camaro Price \| Ordering \| Tracking \| Dealers Discussions	665	06-29-2009 01:00 PM
Stock Exhaust	Davis	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	17	05-29-2009 06:18 PM
Kirk Kerkorian	KILLER74Z28	General Automotive + Other Cars Discussion	10	12-01-2006 04:11 PM

12-18-2009, 12:36 PM	#3
Bruce@raymondsperformance Drives: 2014 Z28 camaro Join Date: Sep 2009 Location: Indy Posts: 705	My 2ss camaro was 30.5" front and rear stock

12-19-2009, 06:57 AM	#4
LH17 Drives: 2010 Camaro SS Join Date: Apr 2009 Location: South Carolina Posts: 50	Thanks!

02-28-2010, 07:04 PM	#6
mdinferno Drives: 2010 IBM 2LT/RS Join Date: Dec 2009 Location: MD Posts: 1,636	Does this mean the springs on the RS is the same height as the SS.

02-28-2010, 10:01 PM	#7
Info@PeddersUSA.com Drives: 5th Gen Rental Join Date: Aug 2007 Location: New England Posts: 1,901	We have measured a lot of SS Camaros and have found as much as a 1/2 variation from one to another, especially in the back. it is very common to see 5 to 8mm variations side to side in the fronts. mike dms

03-02-2010, 04:03 PM	#9
mdinferno Drives: 2010 IBM 2LT/RS Join Date: Dec 2009 Location: MD Posts: 1,636	I just measured my RS from the ground to fender F: 30 1/4" R: 30 1/2". Any other RS owners can confirm these numbers.