08-05-2009, 08:06 PM | #1 |
Drives: 2010 2SS/RS, RJT 04 Silverado Join Date: Oct 2008
Location: Baton Rouge
Posts: 314
|
Fast LSXr Intake
Does any one have any experience yet, with the LSXr intake on their stock or modified LS3? I have heard & read a lot on this and other forums, that it does not perform well...No performance gains. My engine builder has been hearing the same. We are about to finish my LS3-427 Stroker. It will be installed in a few weeks. We will be useing the LSXr intake. We are going to tune the new engine with the stock LS3 intake and then install the Fast intake to get a before and after. This will be done on a dyno. I will share the results. Just wondering if any one else has installed this intake and how it did.
__________________
GIBS SS
|
08-05-2009, 08:45 PM | #2 |
Drives: CTS/CAMARO Join Date: Jun 2009
Location: SEMA/PERF INDUSTRY GUY
Posts: 488
|
How can anyone say the LSXR for the LS3 works or not. They are not shipping them yet. Only the LS7 version. LS3's are due in September.
|
08-05-2009, 09:00 PM | #3 |
Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008
Location: Pittsburgh, PA
Posts: 2,700
|
+1
They are not out yet....The LS7 intake is out and people are gaining about 15HP with it.... I have seen the LS7 version on the dyno and it works...I am sure the LS3 will work also. I have a bunch of them ordered, and I will stand by them!!! |
08-06-2009, 12:52 PM | #4 |
Drives: 2010 2SS/RS, RJT 04 Silverado Join Date: Oct 2008
Location: Baton Rouge
Posts: 314
|
Thanks For The Feedback
:( Looks like some of the folks at FAST/Comp Performance are not up on their products. My engine builder ordered a LSXr-102mm intake about three months ago, when he was ordering all the parts for our LS3 project. He specified that it was for a LS3 with L92 heads and was told it would be coming out in 4-6 weeks...fine. It finally arrived about two weeks ago...great. Posted this thread last night and several of you replied that it was still not available, so I started investigating this morning. Sure enough we received the intake for the LS7. Shipping it back and canceling order for now. Thanks again for your response and info.
If any one else has received one, be sure to check the part # on the box. The part number for the LS3 & L99 is #146102. P/N 146202 is for the LS7. Also, be sure you order/receive the right fuel injector spacer kit that is required.
__________________
GIBS SS
|
08-06-2009, 01:01 PM | #5 |
Okie doke
|
Here is the intake I'm looking at
__________________
|
08-06-2009, 01:36 PM | #6 |
I put the FU back in FUN
Drives: 1969 SS 396 , 2010 Camaro SS Join Date: Jun 2009
Location: Between Weatherford and Azle TX hway730
Posts: 2,129
|
|
08-06-2009, 01:54 PM | #7 | |
Drives: 1968 LS2 powered - Bad Penny Join Date: Jun 2009
Location: Anaheim Hills, CA
Posts: 235
|
Quote:
Everytime we've tested a FAST intake it made more power than a factory intake. Higher output engines showed a better gain and smaller displacement/power engine showed less of a gain.
__________________
Tech Editor for Camaro Performers Magazine
1968 Camaro - 461 RHS LS 700hp, various stuff, called Bad Penny 1968 Camaro - In progress, called Track Rat 2010 Camaro - DSE Suspension, Baer 6S Brakes, Boze Wheels, Nitto NT05 Tires, JBA Exhaust and long tubes, Magnacharger TVS, 660rwhp Forged Eagle 416 LS3 short block, ADM fuel system, Lingenfelter GT-9 cam, G-Force axles, Anvil and Seibon CF parts, Centerforce Dual-Disc Clutch www.fquick.com/steve1968ls2 |
|
08-10-2009, 05:14 PM | #8 |
Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008
Location: Pittsburgh, PA
Posts: 2,700
|
I was just notified by FAST that this intake will not be ready until OCTOBER now. It is now almost one year behind!
|
08-10-2009, 05:27 PM | #9 |
Drives: 2005 Corvette Lemans Blue Join Date: Mar 2009
Location: Boca Raton, FL
Posts: 28
|
Will the FAST 92mm for the LS2 work on the LS3?
__________________
Previous car: 2000 Pontiac Trans Am WS6 convertible. Heads, cam, exhaust....pretty quick
Current car: 2005 Chevrolet Corvette coupe...lots of bolt ons....pretty quick |
08-10-2009, 06:27 PM | #10 |
Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008
Location: Pittsburgh, PA
Posts: 2,700
|
|
08-10-2009, 09:52 PM | #11 | |
Drives: CTS/CAMARO Join Date: Jun 2009
Location: SEMA/PERF INDUSTRY GUY
Posts: 488
|
Quote:
__________________
"everyone wants to go to heaven. but nobody wants to die" "you gotta pay to play"
SEMA PICTURES-PARTS & CARS http://www.pbase.com/haveblue/sema_2009 |
|
08-10-2009, 09:55 PM | #12 | |
Drives: 2SS w/ ZZ427 Package!! Join Date: Oct 2008
Location: Pittsburgh, PA
Posts: 2,700
|
Quote:
|
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
GROUP BUYS: F.A.S.T. LSXr intake and/or Long Tubes Group Buy..Check this out ! | ZZcamaro | V8 Bolt-Ons & Tunes | 209 | 12-28-2009 04:19 PM |
Hennessey V6 Intake Review | Tecca | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 23 | 08-06-2009 05:51 PM |
Fast LSXR 102mm intake | My First Camaro! | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 9 | 08-05-2009 10:08 PM |
FAST LSXR Update: manifold, throttle body, race block | HaveBlue | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 7 | 06-29-2009 06:22 PM |
F.A.S.T. LSXr Intake and Throttle Body Group Buy...Anybody Interested? | ZZcamaro | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 17 | 03-22-2009 01:03 PM |