09-16-2015, 09:36 PM | #1 |
Drives: 2013 ZL1 Black Join Date: Aug 2011
Location: New Jersey
Posts: 85
|
how high do you have to lift the car to install the headers?
Can this be done using Race ramps that are 10" high?
Thank you for any and all advice. |
09-16-2015, 09:47 PM | #2 |
Drives: 2013 HWSE Indy Festial #26 Join Date: Mar 2011
Location: Fredericksburg, VA
Posts: 2,670
|
I used race ramps and when it got to the last part of the install, I raised it up a bit more with a floor jack. Not much, but the race ramps weren't quite high enough.
It will work. Just go slow and you'll be fine.
__________________
There are only so many days in your lifetime. So get out and drive your Camaro...
Dan |
09-16-2015, 10:11 PM | #3 |
Drives: 2015 ZL1 Coupe A6 & 2002 ZO6 Join Date: Apr 2014
Location: Pittsburgh, PA
Posts: 246
|
Yes, you should have enough room. I just used cement blocks and was perfect for me.
__________________
2015 ZL1 A6 Coupe Crystal Red
ATI Balancer w/9.55 (22.5%) lower pulley, FIC1000 Injectors, Stainless Works 2" headers, Stainless Works Retro Cat-Back, V-Max Ported TB, Roto-Fab w/Big Gulp, Elite 2nd Gen Catch Can, Jannetty Tuned. 581 rwhp |
09-17-2015, 10:20 AM | #4 |
Drives: 2000 Camaro SS Join Date: Feb 2010
Location: Louisville, Ky.
Posts: 25,179
|
Just enough to slide under it.
|
09-17-2015, 02:19 PM | #5 |
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,808
|
Ramps...no problem
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
09-17-2015, 03:41 PM | #6 |
Go fast, please.
|
|
09-17-2015, 07:14 PM | #7 |
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,808
|
I've installed 5 sets on ZL1s on my ramps...seriously...no problem. If I were closer, I would. I hate laying on my back, but it is doable.
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
09-17-2015, 07:52 PM | #8 |
Go fast, please.
|
Yeah we're about 5 hours apart. Sucks... Could use someone with some experience in these matters. I've done exhaust work before, just never headers, and definitely not headers on a car this expensive.
|
09-17-2015, 08:02 PM | #9 |
Drives: '21 ZLE A10 Join Date: May 2012
Location: Mechanicsville, VA
Posts: 6,808
|
no worries...this car is cake for headers. I'm currently installing a set of headers on 2012 Toyota Tundra 5.7...what a bastard! On the Yota, I had to remove the front driveshaft, jack the motor off the mounts, and jockey the bolts into very tight places. The ZL1 is very accessible in comparison.
__________________
'21 ZLE A10 Wild Cherry PDR 2:00.78 VIR Full 10.68@131.69 1.68 60'
'17 ZL1 A10 Mosaic Black PDR/Nav 2:03.08 VIR Full 11.003@129.2 1.75 (sold) '15 Z/28 #325 Black a/c & stereo. 2:10.1 VIR Full (sold) '12 ZL1 A6 Black 10.52@131 1.55 60' 2:13 VIR Full (sold) |
09-17-2015, 08:05 PM | #10 | |
Go fast, please.
|
Quote:
|
|
|
|
|
|