10-01-2012, 05:05 AM | #1 |
|
Help on launching with Hoosier Slicks @ 678/671
I finally broke down and ordered a 9" with 3.91 gears, weld wheels, skinnies and Hoosier 28" slicks. My car is an M6 with 678 RWHP and 671 torque. I have been on drag radials since I got the car. Anyone here running a similar setup that could give me some ideas on a starting point for how you are launching on slicks. This will be on the track. What are the better 60' times you have seem on similar setups?. What air pressure are you using and have you had any cases where the tires have slipped on the rims? My best time on MT drag radials has been 10.93 but that was at 638/601. Thanks
__________________
LPE 417 - TVS2300 787 RWHP 759 Torque - Built by WWW.KYSPEED.COM
|
10-11-2012, 05:49 AM | #2 | |
Drives: 10 LS3 2SSRS IOM,21 ZLE Wild Cherry Join Date: Aug 2009
Location: Denver
Posts: 2,126
|
Quote:
__________________
LPE 650+,IOM Pearl White Rallys
860 RWHP 924 RWTQ,TVS2300 10/14 OD 2.75/NW 102mm,RDS/FLOWED "109" SHOT/LPE NCC NLP spoiler/GM splitter/Torq HE-fans/oil coolers/IC1000cc Squash twins,GT9,Coil Covers,Mats,Pedals/ADM Gauges,Race Scoop/Trunions DDS CVs,Carbon F DS/RPM L6/LPE 9.5 3.73/Pedders HD bushes,align kit RB 2-piece rotors,S/S Lines,Hawk HPE Pads/Forgeline SP3P/Weld RTS Ceramic ARH 2" LT/3" X-pipe,Corsa Touring/BMR TA,Toe,LCA,DS Loop StreetSlayer BC3/MTI Shifter-Trans mt/Hotchkis CB/Monster CC/SJM LineLock PFADT Coil Overs,Sways,Links,Mounts,SF Bushes,Camber Kit LPE Brotherhood . |
|
10-12-2012, 12:01 AM | #3 |
Drives: 2009 Cobalt SS/TC Join Date: Sep 2009
Location: Sandusky, Ohio
Posts: 368
|
Rev it up and dump it. That's how you launch on slicks. A 2 step would be good too.
__________________
2009 Cobalt SS/TC: 10.89 at 133mph
|
10-12-2012, 08:44 AM | #4 |
|
I have gone 1.58 60' at 10.61 sec. with Hoosier Slicks at 15psi and M&H Skinnies with a little over 700HP.
|
10-12-2012, 08:48 AM | #5 |
Drives: 2010 1SS Join Date: Jan 2010
Location: Tampa, FL
Posts: 1,002
|
There are quite a few guys with manual transmissions on the Official 60' List Thread some of them running down into the 1.40's. The thread is a good resource to see what mods are yielding what results. If you don't get any answers here, feel free to post in that thread or PM the members to ask them about their lauch techniques.
And when you get back to the track, post your info as well! |
10-13-2012, 09:55 AM | #6 | |
|
Quote:
__________________
LPE 417 - TVS2300 787 RWHP 759 Torque - Built by WWW.KYSPEED.COM
|
|
|
|
|
|