09-27-2011, 01:34 PM | #1 |
|
Hawk Performance Ceramic Pad Noise
I am removing this because apparently the issue is not due to Hawk but instead is likely caused by the installation shop screwing up the job. Hawk has been great about this and is even sending me a new set of pads just in case.
__________________
MBRP Catback/Magnaflow Resonated X/Airraid V2 CAI/Dash ABL/Interior LEDs/Custom Paint/Jet Coated American Racing LT Headers/High Flow cats/Trifecta Tune Last edited by DevilKnightFalcon; 09-27-2011 at 03:00 PM. |
09-27-2011, 01:37 PM | #2 |
Banned
|
yes i agreee the stocks use a counter weight, and on occasion i here squeals... but my stockers squeal...created crazy aweful dust and heated up too much...its a trade off....maybe u just had a super bad issue ...many guys run hawk...this the first time i hear this.
|
09-27-2011, 01:48 PM | #3 |
|
Here is a short video of my problem. I have a longer one I will post when I get home.
__________________
MBRP Catback/Magnaflow Resonated X/Airraid V2 CAI/Dash ABL/Interior LEDs/Custom Paint/Jet Coated American Racing LT Headers/High Flow cats/Trifecta Tune |
09-27-2011, 02:08 PM | #4 |
Blown Cool Breeze
Drives: 2011 Black on Black 2SS M6 Join Date: Jul 2010
Location: Pinehurst NC
Posts: 1,027
|
To me the video sounds like the classic case of the install shop not de-glazing the rotors before pad change.Just slapping the new one's on and calling it good.Seen it a thousand times
If the rotors are not machined,the bare minimum is to Ruff up the surface to removed the previous pads imbeded compounds. If this is not done and the proper break-in procedure not done after the new pads are installed,the new pads will just glide over the glazed rotors and make the squealling noise. This is a very simplified explanation and there is much more to it,but you get the idea. The problem is NOT the Hawk pads....it was the installers.
__________________
2011 Black on Black 2SS M6
Had a 2010 IBM 2SS M6 Enjoy life.Think of all the women on the Titanic who passed up dessert. |
09-27-2011, 02:12 PM | #5 |
NEcamaro5
|
CAN DEGLAZING BE DONE ON ARE OWN?
|
09-27-2011, 02:13 PM | #6 |
Banned
|
i get that squeal ...but not often...and like the previous guy said i didnt resurface..so i expect it...and its not a big thing...doesnt happen that often, and usually happens when the pads are cold , then leaves
|
09-27-2011, 02:58 PM | #7 |
|
It happens for me when the pads are warm after driving for awhile. However I think you are right. The shop i had them installed at is one I have used many times but I am pretty sure they screwed this up.
__________________
MBRP Catback/Magnaflow Resonated X/Airraid V2 CAI/Dash ABL/Interior LEDs/Custom Paint/Jet Coated American Racing LT Headers/High Flow cats/Trifecta Tune |
09-27-2011, 04:01 PM | #8 |
v It bites.
Drives: 2011 IBM 2SS/RS Join Date: May 2008
Location: Orlando, FL
Posts: 3,585
|
...thhhhatttt would drive me bat s--- crazy.
__________________
2011 2SS/RS
Performance: 439 RWHP: 226/236 Comp Cam, Kooks 1-7/8, CAInc, Borla S type, Vmax TB, Rx Catch Can, Trans cooler, SLP 160 termo, Melling high volume, Eibach Springs/Sways 1" drop, Whiteline complete bushing kit. |
09-27-2011, 07:26 PM | #9 |
Banned
|
Get the rotors resurfaced...then tell how u feel...so far I love the hawks
|
09-27-2011, 09:27 PM | #10 |
Drives: 2010 Camaro LS M6 Inferno Orange Join Date: May 2010
Location: Lebanon, OH
Posts: 1,672
|
I installed the Hawk HPS pads 2 weekends ago and haven't heard a peep out of them - put on about 400 miles. I did not do anything to the rotors, but I did do the break-in procedure (accelerate to 55, brake hard to 35, accelerate to 65, brake hard to 35, accelerate to 75, brake hard to 35).
__________________
Gordy
Injen CAI / Solo Mach-X LLT / Solo High-flow res-cats / Barton short shifter / RX Catch Can / RPI Gills / 35% tint / LED Footwell Lighting Front & Rear / Pedders Street 1 / Pedders steering rack bushing / SS struts / Pfadt drop springs / VMax Ported Throttle Body / Spohn Toe Rods / Spohn Trailing Arms / Trifecta Tune / MACE 25mm Intake Spacers Find me on Facebook: http://www.facebook.com/gahammerle |
09-28-2011, 03:40 PM | #11 |
Banned
|
holy molely i didnt even do break in...ahhh i dont need too...my rotors will surface the brakes.lol
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
V8 Camaro Performance Upgrades List | Milk 1027 | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 93 | 08-30-2021 05:56 PM |
V6 Camaro Performance Upgrades | rtcat600man | Camaro V6 LLT Engine, Exhaust, and Bolt-Ons | 387 | 09-19-2019 06:53 PM |
Hawk Performance Brake Pad "Updated" | KILLER74Z28 | Suspension / Brakes / Chassis | 34 | 05-04-2016 11:11 AM |
CEL - P1682 | PSU SS | Tuning / Diagnostics -- engine and transmission | 4 | 09-29-2011 07:27 PM |
Stainless Works Longtube w/High Flow cats plus Hawk Ceramic Brake Pads | Xplosive Performance | V8 Bolt-Ons & Tunes | 5 | 04-13-2011 08:03 AM |