02-01-2017, 06:30 PM | #1 |
Drives: 2015 Chevy Camaro 1SS Join Date: Jun 2016
Location: Hampton, Va
Posts: 53
|
Airbag resistor to run with racing seats!?
I've done a lot of searching on this forum about the resistor trick. Seems to be a few threads that dropped off with unsure info. Was just coming back to see if theres any new information about getting the airbag light off. I just ordered Braum seats and would like to keep that light off when I install them.
My main goal is to keep that light off after the install so any extra info would be awesome! |
02-01-2017, 06:38 PM | #2 |
Drives: 2015 Chevy Camaro 1SS Join Date: Jun 2016
Location: Hampton, Va
Posts: 53
|
Picture for attention
|
02-01-2017, 07:45 PM | #3 |
|
Nice car!
I too have been seeking this mystery. Seems to be a solution but nobody willing to discuss. I want to keep all my airbags but the seat side air bags, so I can do a light weight race seats up front. I have held off from buying the seats because I do not want to mess the air bags crap up. GRRRRR.. I remember the days with no air bags. When they put front dash air bags that was ok. But now its just way over done with air bag crap and sensors.
__________________
Car mods: never enough!
|
02-02-2017, 04:41 PM | #4 | |
Drives: 2015 Chevy Camaro 1SS Join Date: Jun 2016
Location: Hampton, Va
Posts: 53
|
Quote:
|
|
02-02-2017, 06:03 PM | #5 | |
|
Quote:
__________________
Car mods: never enough!
|
|
02-03-2017, 09:22 AM | #6 |
Drives: 2015 Chevy Camaro 1SS Join Date: Jun 2016
Location: Hampton, Va
Posts: 53
|
Bump. Is there just no info on this or am I missing something?
|
02-04-2017, 12:49 PM | #7 |
Drives: 2011 2SS/RS M6 Join Date: Oct 2015
Location: Utah
Posts: 1,940
|
Between 2.1 and 4 ohm for any airbag in the seat. The passenger presence system cannot be defeated by any means I know of, maybe someone makes a faker module or program. The sensor can't be removed because it's a module that communicates to the airbag module.
|
02-16-2017, 06:24 AM | #8 |
Drives: 2015 2ss Join Date: Jun 2015
Location: Wooster ohio
Posts: 586
|
How do you wire the resistor in though?
|
02-17-2017, 08:43 AM | #9 |
IG @Brian_ _Self
Drives: 2010 Camaro 2SS M6+17'Tesla Model S Join Date: Nov 2012
Location: Bristol, TN : Instagram @Brian_ _Self
Posts: 804
|
I'm going to do a write up later today. I'll post the link
Sent from my iPhone using Tapatalk
__________________
|
02-17-2017, 03:35 PM | #10 | |
|
Quote:
__________________
Car mods: never enough!
|
|
02-18-2017, 10:58 AM | #11 | |
Quote:
http://www.camaro5.com/forums/showthread.php?t=434170
__________________
"The walls are white, the track is grey, the grass is green, and the sky is blue... your job is to keep them all where they belong." - Johnny Rutherford |
||
02-20-2017, 04:19 PM | #12 |
|
Bumpso
__________________
Car mods: never enough!
|
03-02-2017, 02:50 PM | #13 |
Drives: 2015 Chevy Camaro 1SS Join Date: Jun 2016
Location: Hampton, Va
Posts: 53
|
This is awesome!
|
03-02-2017, 04:52 PM | #14 |
Drives: Pontiac G8 GT Join Date: Jan 2011
Location: Toledo
Posts: 115
|
from how i understand it... its not just the light that is annoying... but if you remove the seats and do trick the complete system, then NONE of your airbags will work at all.. the complete system is disabled!!
__________________
Sleeper Pontiac G8 Gt; LSX 430 with Procharger F1x ; 25psi; 4L80E conversion; Hendrix 9" rear/driveshaf; Camaro brembos; (1209rwhp
|
|
|
|
|