Charmaro_ZL1's Build - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Charmaro_ZL1 · 07-04-2018, 02:00 PM

Hi everyone!

I picked up my Victory Red 2013 ZL1 on 06/13/18

The car has a few mods on it already and is tuned to 562whp. It has Texas speed catted longtubes headers, Cold Air Inductions Intake, Lingenfelter 2.38 upper pulley.

This car is a daily and AutoX car until I find a little pickup to drive around daily so I can full race car the ZL1.

Current build list: Installed/Purchased/Planned
Texas Speed Longtubes
2.38 upper pulley
PFADT sway bars
PFADT street/track coilovers
BMSPEC front splitter
19x10.5 Konig Ultraform 21lbs each
305/35-19 square setup tires
Cold air Inductions intake
PFADT bushings
BMSPEC GT Rear Wing
Vengeance racing tune

Some current photos soon!

Also I'll update this with every new discovery, part, race etc.

PowerCreep · 07-05-2018, 01:53 AM

Nice!

Charmaro_ZL1 · 07-06-2018, 06:41 AM

PFADT coilovers are supposed to be here on Wednesday of next week. I should be able to put them on the day I get them or the following day.

First AutoX is the 15th of this month and then the following week on the 21st.

Next up is some good wheels and tires. I'm looking for a good light 19x11 setup, anyone know how much the MRR wheels weigh?

Been thinking about picking up the Konig Ultraform wheels, 19x10.5 only weighs 21lbs. But not sure how they would look on the ZL1. Any suggestions welcome!

Charmaro_ZL1 · 07-07-2018, 05:08 PM

Just purchased the 19x10.5 Konig Ultraform wheels in graphite, and 305/30-19 Bridgestone RE71r.

The setup should be much lighter than the stock setup, and I'll get to work on it next weekend when I get to the autocross course.

I updated the Original post, I'll post before and after pics of the coilovers and wheels and tires.

Charmaro_ZL1 · 08-23-2018, 06:40 PM

An update to the car! Sorry I have been out lately work and school and racing have me tied up quite a bit but here is the car now with the new list of mods:

I changed from the APR front splitter to the BMSPEC front splitter due to the significant boost of aero it provides, I also ordered BMSPECs Carbon GT wing that should be showing up in a week or two. I have the Sway bars Installed as well. And finally the suspension is tuned up pretty well. Now I am just tuning it with the sway bars to get that perfect nuetral with a little Oversteer bias. But we will see how it works. Here are some photos, and I'll update the first post to reflect the changes.

07-04-2018, 02:00 PM	#1
Charmaro_ZL1 Drives: 2013 Chevrolet Camaro ZL1 Join Date: Jul 2018 Location: North Texas Posts: 6	Charmaro_ZL1's Build Hi everyone! I picked up my Victory Red 2013 ZL1 on 06/13/18 The car has a few mods on it already and is tuned to 562whp. It has Texas speed catted longtubes headers, Cold Air Inductions Intake, Lingenfelter 2.38 upper pulley. This car is a daily and AutoX car until I find a little pickup to drive around daily so I can full race car the ZL1. Current build list: Installed/Purchased/Planned Texas Speed Longtubes 2.38 upper pulley PFADT sway bars PFADT street/track coilovers BMSPEC front splitter 19x10.5 Konig Ultraform 21lbs each 305/35-19 square setup tires Cold air Inductions intake PFADT bushings BMSPEC GT Rear Wing Vengeance racing tune Some current photos soon! Also I'll update this with every new discovery, part, race etc. Attached Images Last edited by Charmaro_ZL1; 08-23-2018 at 06:46 PM.

08-23-2018, 06:40 PM	#5
Charmaro_ZL1 Drives: 2013 Chevrolet Camaro ZL1 Join Date: Jul 2018 Location: North Texas Posts: 6	An update to the car! Sorry I have been out lately work and school and racing have me tied up quite a bit but here is the car now with the new list of mods: I changed from the APR front splitter to the BMSPEC front splitter due to the significant boost of aero it provides, I also ordered BMSPECs Carbon GT wing that should be showing up in a week or two. I have the Sway bars Installed as well. And finally the suspension is tuned up pretty well. Now I am just tuning it with the sway bars to get that perfect nuetral with a little Oversteer bias. But we will see how it works. Here are some photos, and I'll update the first post to reflect the changes. Attached Images

07-05-2018, 01:53 AM	#2
PowerCreep Drives: '14 SS 509.5 RWHP Join Date: Jun 2017 Location: Little Rock, AR Posts: 59	Nice!

07-06-2018, 06:41 AM	#3
Charmaro_ZL1 Drives: 2013 Chevrolet Camaro ZL1 Join Date: Jul 2018 Location: North Texas Posts: 6	PFADT coilovers are supposed to be here on Wednesday of next week. I should be able to put them on the day I get them or the following day. First AutoX is the 15th of this month and then the following week on the 21st. Next up is some good wheels and tires. I'm looking for a good light 19x11 setup, anyone know how much the MRR wheels weigh? Been thinking about picking up the Konig Ultraform wheels, 19x10.5 only weighs 21lbs. But not sure how they would look on the ZL1. Any suggestions welcome!

07-07-2018, 05:08 PM	#4
Charmaro_ZL1 Drives: 2013 Chevrolet Camaro ZL1 Join Date: Jul 2018 Location: North Texas Posts: 6	Just purchased the 19x10.5 Konig Ultraform wheels in graphite, and 305/30-19 Bridgestone RE71r. The setup should be much lighter than the stock setup, and I'll get to work on it next weekend when I get to the autocross course. I updated the Original post, I'll post before and after pics of the coilovers and wheels and tires.