You are browsing camaro5 
 |
|
11-24-2011, 08:38 PM
|
#1 |
 Drives: pro touring 69 camaro Join Date: Nov 2011
Location: ocala fl
Posts: 5
|
engine control modul?
High guys there’s a lot of great supercharger information on this site. I’m building a 69 camaro [I know its not a 5 gen just don’t hold that against me]. It’s going to be running a 406ci sbc. With distributorless ignition and as Maggie TVs 2300 supercharger. And I’m doing some research are all you charger guys using stock engine control module with custom tune or custom ecu’s.... thanks for your help …Anthony
|
|
|
|
11-24-2011, 09:21 PM
|
#2 |
|
instigator
Drives: 2020 6.2 Trail Boss, 2022 XC90 Join Date: Jan 2010
Location: 72034
Posts: 3,979
|
Stock ECM tuned.
Check into gm's hot rod ECM/wiring harness set up... Or do a FAST.
__________________
-John S.
|
|
|
|
|
11-24-2011, 09:28 PM
|
#3 |
|
Drives: pro touring 69 camaro Join Date: Nov 2011
Location: ocala fl
Posts: 5
|
Thanks I appreciate it
|
|
|
|
|
11-24-2011, 09:39 PM
|
#4 |
|
Account Suspended
Drives: Anything Blown Join Date: Aug 2010
Location: SoCal
Posts: 1,194
|
What type of accessories (belt line) are you running?
|
|
|
|
|
11-24-2011, 11:22 PM
|
#5 |
   
|
stock ecm tuned
|
|
|
|
|
11-28-2011, 09:30 PM
|
#6 |
|
Drives: pro touring 69 camaro Join Date: Nov 2011
Location: ocala fl
Posts: 5
|
I’m going to add 2 idler pulleys to a vintage air frontrunner . thanks again guys
Last edited by anthonys 69; 11-28-2011 at 09:56 PM. |
|
|
|
|
11-28-2011, 10:10 PM
|
#7 |
|
Most hated in NM....
Drives: Sold the 6POINT2, went to a 50THZ06 Join Date: Sep 2011
Location: New Mexico
Posts: 2,904
|
No one will hold it against you that your rocking a 69... We do need pics however
__________________
 |
|
|
|
|
11-29-2011, 08:28 AM
|
#8 |
Drives: 8 second C5 Drag Car, C6 Road racer Join Date: Sep 2009
Location: Cream Ridge, NJ 609-752-0321
Posts: 778
|
I have a brand new Accel gen 7 set up for an LS based engine, harness-PCM everything you need. It was purchased for a project like yours that was never finished. It can do more then you probably need it too and was almost 4k new, I would be happy with $1,800. PM if interested.
|
|
|
|
|
11-29-2011, 09:31 PM
|
#9 |
|
Drives: pro touring 69 camaro Join Date: Nov 2011
Location: ocala fl
Posts: 5
|
angel speed here’s a rendering of what’s going to look like
Thanks East coast for the offer. I own a garage in Ocala Florida and I’m used to working with obd2 diagnostics factory wiring etc. so I was very happy to find out that I can install a 58 tooth crank gear a crank sensor a cam sensor where the distributor would be and run individual coils and a ls computer on a sbc Ever since then Im reading and learning as much as i can. I found out that I could run a zl1 fuel pump at this site and have since found a fuel tank the fuel pump will fit... Last edited by anthonys 69; 12-07-2011 at 08:38 AM. |
|
|
|
|
12-06-2011, 05:06 PM
|
#10 |
|
Drives: pro touring 69 camaro Join Date: Nov 2011
Location: ocala fl
Posts: 5
|
 hope you like my girl vicky
|
|
|
|
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Diagnostic Trouble Codes (DTCs) for OBD II equipped GM vehicles | steeleshark2 | Tuning / Diagnostics -- engine and transmission | 11 | 04-08-2020 10:49 PM |
| 5th Gen Suspension -- The Book | JusticePete | Suspension / Brakes / Chassis | 151 | 05-07-2015 05:52 PM |
| CEL - P1682 | PSU SS | Tuning / Diagnostics -- engine and transmission | 4 | 09-29-2011 07:27 PM |
| Acronyms? | KEEP RT | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 20 | 03-11-2011 08:57 PM |
| Why i think you cant do a Dyno in the same day | 2SSRS@Gen5diy | Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons | 123 | 10-22-2009 07:37 PM |
