02-16-2013, 01:25 PM | #1 |
THE YETI
Drives: 2SS RS Join Date: Jan 2013
Location: chicago
Posts: 411
|
catch can install
Just got my catch can but i wasn't sure if the check valve goes to the inlet of the can or the outlet. I believe its the outlet Also what did you guy use to cut the steal braided line.
|
02-16-2013, 01:30 PM | #2 |
Drives: 2010 SS L99 Inferno Orange Join Date: Apr 2012
Location: Texas Coast
Posts: 1,167
|
|
02-16-2013, 01:39 PM | #3 |
Drives: Camaro SS Join Date: Mar 2010
Location: Motorcity Dragway
Posts: 978
|
Cutting wire with diagonal cutters, commonly called dikes, u need to pey attenshun 2 where the waist end may not becausehardened wire, like instrument strings, can take off with spring-like intensity. If you’re cutting heavy wire, position the wire all the way in, at the joint between the jaws, for maximum leverage.
__________________
11.90's w/headers, CAI, custom tune, slicks/skinnys, shifter & 100+ Ethyl.
|
02-16-2013, 01:45 PM | #4 |
Account Suspended
Drives: 2012 Camaro RS, RX supercharged Join Date: Dec 2009
Location: Bradenton, FL
Posts: 6,063
|
Checkvalve goes on the outer fitting and connects to the intake manifold vacuum barb. The inner fitting gets no checkvalve in the line and connects to the crankcase (valley cover or rear of valve cover).
To cut, wrap w/masking tape tight at the spot to help keep the braid from fraying. A band saw, abrasive cut-off wheel, or like Smirnoff describes. Most diagrams are on the website, lower left hand corner. |
02-16-2013, 01:49 PM | #5 |
Drives: 2011 IOM 2SS/RS Join Date: Dec 2010
Location: Chatham, Illinois
Posts: 756
|
From the my experience the tape and a cutoff wheel works best.
Sent from my HTC One X using Tapatalk 2
__________________
American Racing 1 7/8" Headers and Hi-Flow Cats, CAI cold air intake, Flowmaster AT exhaust, Vengeance Racing Stage 2 cam, VMax ported throttle body, TEA valve springs and titanium retainers, Trick Flow hardened pushrods, 180* T-stat, Comp Trunion kit, ZL1 Fuel Pump, ADM Fuel Pump Control Module, 20% window tint, Whipple Supercharger. Tuned by Mike Norris Motorsports. 656rwhp/584rwtq @10 PSI.
|
02-16-2013, 03:29 PM | #6 |
THE YETI
Drives: 2SS RS Join Date: Jan 2013
Location: chicago
Posts: 411
|
Thank guy for the replies im going to start the instal now. With the help im sure everything is going to go fine now. I just wish it wasn't 20 degrees out no heater in the garage.
|
02-16-2013, 11:13 PM | #7 | |
THE YETI
Drives: 2SS RS Join Date: Jan 2013
Location: chicago
Posts: 411
|
Quote:
Well install went smooth just to help the next guy when cutting the hoses the inlet hose is cut at 14 1/2 inches. The outlet hose is cut at 15 inches this is for the braided line. I used a cut off tool wrapped the area tight with blue painters tape.The cut came out clean looks nice Im happy how it came out. Now one more thing the Vmax painted ported throttle body. Ill order that in a week or so then thats it for dress up under the hood. Last edited by Rocco70; 02-17-2013 at 12:01 AM. |
|
02-18-2013, 11:37 AM | #8 |
FreakyFast!
Drives: 2010 2SS/RS S/C NicKey #55 Join Date: Feb 2011
Location: Central Illinois
Posts: 931
|
Looks nice. I just ordered an Elite can. Contemplating the SS braided hoses or not. You going with a Summit White Throttle Body as well?
__________________
2010 2SS/RS #55 NicKey Stage 2S Super-Camaro custom painted by Pete (Mr. Showstopper) Build Thread: http://www.camaro5.com/forums/showthread.php?t=250743 |
03-12-2013, 10:46 PM | #9 |
THE YETI
Drives: 2SS RS Join Date: Jan 2013
Location: chicago
Posts: 411
|
Yes I am im waiting on it now cant wait should be here in a week or so.
|
03-13-2013, 12:55 AM | #10 |
Chu no guat a hasa is?
Drives: 14 Jeep G Cherokee Overland HEMI Join Date: Jun 2011
Location: Some where in So Cal
Posts: 4,273
|
Nice OP.
I have the same setup. I used a box cutter to cut the braided hose. Took a while.
__________________
11 2SS/RSL99No Longer Stock (Sold) 6/19/14:AAC Plasma DRL's | Plug n play harness | Elite CC | Tint: 35% & 5% | LED Dome light | Show-N-Go Plate Holder | Flowmaster AT | C.A.I. Intake | VMAX CNC Spiral Ported TB | Husky Splash Guards
|
|
|
|
|