07-02-2009, 10:54 PM | #1 |
Drives: 2010 Camaro 2LT/RS Join Date: Nov 2008
Location: Toronto
Posts: 280
|
noise from under center shifter?
Iv got a 2lt m6 just got back from a drive parked it in 1st like I always do nd put the hand break up then b4 I shut the car off I heard a loud thump come from under my shifter area ...I bacled out nd drove around the block nd everything seemed normal. Has this happend to ne one or does ne one knw wut this could have been?
|
07-03-2009, 05:37 AM | #2 |
:chevy:
Drives: 2LT/RS Join Date: Jun 2008
Location: Toronto
Posts: 13,033
|
Im not to sure what that is. I also get sounds like when im rolling in first, just rolling, the minute i press the clutch down, it sounds like my gears are banging around, do you get the same thing.
|
07-03-2009, 06:52 AM | #3 |
Drives: 2010 Camaro 2LT/RS Join Date: Nov 2008
Location: Toronto
Posts: 280
|
Ya I get that seems pretty normal but wut I heard didn't sound right..hopefully its nothing
|
07-14-2009, 11:55 AM | #4 |
|
bring it to the dealer
|
07-20-2009, 02:10 PM | #5 |
Drives: 2LT/BB 3.6 V6 6-M Jun'09 #A9100242 Join Date: Jul 2009
Location: New York
Posts: 543
|
I had the same noise in my 2LT/M6 and at a mileage of 150 put in, It went back to the dealership. The next mourning I received a call from them explaining that it was my neglect and the cost was at $2000.00, but they were covering the bill, “Huh?" I haven’t even drove the car no more than 3 days. Still waiting for it. Hope that for your problem is nothing major like mine.
|
07-20-2009, 03:14 PM | #6 |
Did they say what the problem was???
__________________
2019 1LT/RS Summit White....
|
|
07-24-2009, 12:35 PM | #7 |
Drives: 2LT/BB 3.6 V6 6-M Jun'09 #A9100242 Join Date: Jul 2009
Location: New York
Posts: 543
|
Still getting the run-arounds from the service shop, but a staff agent got the order sheet and mentioned the following:
*Clutch plate was sticking on splines and dragging causing the clutch throw-out bearing to fail. *warped clutch plate *Clutch diaphram, broken finger Order: 1- Clutch Plate 2- Clutch diaphragm 3- Clutch throw-out bearing The other problem that i'm also facing is the time frame for the parts to be shipped to the dealership, since the car is so new. I'll keep you updated next week. |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
first Camaro Hurst shifter installed in 2010 Camaro | 2SSRS@Gen5diy | V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) | 347 | 10-17-2009 12:10 PM |
Dumb question (sorry in advance) Hurst Shifter | 2Muchmark | 5th Gen Camaro SS LS LT General Discussions | 0 | 04-16-2009 04:52 PM |
camaro update (husrt shifter, cgm) | gss9909 | 5th Gen Camaro SS LS LT General Discussions | 24 | 03-27-2009 06:33 PM |
Short Throw Shifter Constrained?? | josh1147 | Camaro Price | Ordering | Tracking | Dealers Discussions | 75 | 02-19-2009 12:51 PM |
Thread Size on Hurst Shifter? | r0cketdr | Cosmetics and Lighting Modification Discussions | 0 | 11-18-2008 01:29 PM |