Everyone with a Spoiler... PLEASE READ! - Page 2 - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

Gameover · 06-27-2009, 06:09 PM

I don't mean to

but, I was thinking the same about the air pump, if you have a flat and plug it yourself on the side of the road, that's not the time to find out it doen't work!

Kenny · 06-27-2009, 06:21 PM

Quote:

Originally Posted by RoyalKev

Make sure they dont scratch everything up while fishing for the nuts.

Everyone knows you don't fish for nuts

.......you hunt them.

*mlee* · 06-27-2009, 06:37 PM

Quote:

Originally Posted by Kenny

Everyone knows you don't fish for nuts

.......you hunt them.

Sorry Kenny... I can't resist...

Black5thgen · 06-27-2009, 06:59 PM

I already had to take my car back to the dealer so they could fish out a bolt inside the trunk lid.

tones2SS · 06-27-2009, 07:12 PM

Quote:

Originally Posted by jpsuperman81

Good looking out

I agree. Good for passing on this info!

69 Hugger · 06-27-2009, 07:42 PM

Quote:

Originally Posted by mlee

True... some lockwashers might be a good add too...

Those nuts should have a locking flat connected to the nut, the lock tight would be a good fix.

novajess1972 · 06-27-2009, 08:16 PM

Quote:

Originally Posted by Sinergy

Oh, that's great...Now I have to supply my trunk monkey with a ratchet set..

It may have been your trunk monkey that loosened them to begin with. Did you forget to to feed him again? You know how that pisses them off!!!!!!

heinzd01 · 06-27-2009, 08:34 PM

Thanks for the info! My spoiler nuts needed a 1/4 turn.

Alfieboy · 06-27-2009, 09:43 PM

Thos enuts th e10mm .. I woul suggest.. you go to local hardware store.. get (4) or how many you need Nylock nuts.. they will never back off.. even using a reg lock washer..you cannot overtighten those nuts ..so a nylock nut you can snug it to where its firm.. YET it will never beack off..use them exclusively on the Rollback... (vibration)....

: wave:

Rick

*mlee* · 06-27-2009, 10:24 PM

Agree... nyLock nuts with a regular flatwasher would work well..

Who knows... all of these nuts may have been tight from the factory and are just vibrating loose with no lock washers etc.

9c1ny · 06-27-2009, 10:34 PM

mine has something rattling around in the decklid but I pulled the grommets and everything is tight

*mlee* · 06-27-2009, 10:40 PM

Quote:

Originally Posted by 9c1ny

mine has something rattling around in the decklid but I pulled the grommets and everything is tight

Probably like post #11... an extra nut. Someone probably saw it missing and replaced it before the caps went on.

3GPa · 06-28-2009, 11:25 AM

Nice to know. If my car ever gets beyond 1100.
I'll try to remember and check this out!

Gus

B.A.Brunswick · 06-28-2009, 02:25 PM

Good Call.....I just checked the 4 nuts securing the spolier on my 2LT and sure enough, they were LOOSE!

So I took my 10MM socket and tightened them up

Thanx for the info !!

06-27-2009, 06:09 PM	#15
Gameover Drives: 2010 2SS/RS ABM Camaro Join Date: Mar 2009 Location: San Antonio Posts: 503 View My Garage	I don't mean to but, I was thinking the same about the air pump, if you have a flat and plug it yourself on the side of the road, that's not the time to find out it doen't work! __________________ Out of order!

06-27-2009, 09:43 PM	#23
Alfieboy Madman Drives: 2017 1SS Join Date: Jun 2009 Location: RICHMOND VA Posts: 1,405 View My Garage	nuts Thos enuts th e10mm .. I woul suggest.. you go to local hardware store.. get (4) or how many you need Nylock nuts.. they will never back off.. even using a reg lock washer..you cannot overtighten those nuts ..so a nylock nut you can snug it to where its firm.. YET it will never beack off..use them exclusively on the Rollback... (vibration)....: wave: Rick

06-27-2009, 10:24 PM	#24
mlee CamaroFans.com Drives: ZLE & ZR2 Join Date: Oct 2008 Location: Conroe, TX Posts: 37,490 View My Garage	Agree... nyLock nuts with a regular flatwasher would work well.. Who knows... all of these nuts may have been tight from the factory and are just vibrating loose with no lock washers etc. __________________

06-27-2009, 10:34 PM	#25
9c1ny Drives: C6 Zed-oh-six Join Date: May 2009 Location: Buffalo NY Posts: 677	mine has something rattling around in the decklid but I pulled the grommets and everything is tight __________________

06-28-2009, 02:25 PM	#28
B.A.Brunswick Drives: 2LT/RS/Black/6MT Join Date: Mar 2009 Location: GA Posts: 20	Spoiler Good Call.....I just checked the 4 nuts securing the spolier on my 2LT and sure enough, they were LOOSE! So I took my 10MM socket and tightened them up Thanx for the info !!

06-27-2009, 06:59 PM	#18
Black5thgen Account Suspended Drives: 2007 C6 Join Date: Apr 2007 Location: chicago Posts: 2,251 View My Garage	I already had to take my car back to the dealer so they could fish out a bolt inside the trunk lid.

06-27-2009, 08:34 PM	#22
heinzd01 Drives: 2010 SS RS, 1976 Type LT Join Date: Sep 2008 Location: Jamestown, OH (East of Dayton) Posts: 1,275 View My Garage	Thanks for the info! My spoiler nuts needed a 1/4 turn.

06-28-2009, 11:25 AM	#27
3GPa Drives: SOLD/2SS/RS Painted Rally Stripes Join Date: Apr 2009 Location: Oregon Posts: 325 View My Garage	Nice to know. If my car ever gets beyond 1100. I'll try to remember and check this out! Gus

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
High Wing Spoiler or Not?	RSm1thX	Cosmetics and Lighting Modification Discussions	109	04-03-2013 05:36 PM
Revenge of the fallen (Spoiler Alert!!! DO NOT READ IF YOU HAVE NOT SEEN IT!!!)	manimsoblack	Off-topic Discussions	81	07-23-2009 09:11 PM
Answers to people asking about the highwing spoiler;	DJ ATOMIX	Cosmetics and Lighting Modification Discussions	21	06-29-2009 07:46 PM
Request for spoiler mount pictures	KK2010SS	Camaro Photos \| Spyshots \| Video \| Media Gallery	2	05-27-2009 10:35 AM
Poll: Should Chevrolet Offer Spoiler Delete Option on SS and RS cars?	Hylton	Cosmetics and Lighting Modification Discussions	36	03-18-2009 10:18 AM