Multiple Throttle Bodies, LT headers, ZL1 Pump w/ADM FPCM, JBA Axle Back

[2010SSRSM6]

I'm scheduled to make some major changes to my car on the 18th of May and have several things either coming off the car or sitting in my garage and they are in need of finding a new home. If they are on the car, they will not be available until CMS has a chance to get them off the car. Unfortunately where they are on the car, pic's will have to wait. I'll try to get pics of the other stuff on here A.S.A.P.



Throttle bodies:

I have the following throttle bodies that I will be parting with.



BBK 95MM: I've ran this on my car for 30k miles and had ZERO issues with it. I'm getting a developmental TB and will no longer have a need for this one. It is currently on my car and will have to wait until after the 18th before it is available.

SOLD!!!!!





BBK 102mm: This TB has roughly 10k miles on it. ZERO ISSUES with it. If you have a blower, you would greatly benefit having a ported snout if you are going to run anything larger than the 95mm. That being said, I did pick up 10rwhp over the 95mm without tuning and I'm sure it would have picked up more with the tune. This would be going on my car on the 18th, but I'm testing another product so I can't.


Retail $399 Asking $300 o.b.o.



VMAX ported factory TB in Inferno Orange: I am currently using the electronics off this TB on my BBK TB that is on the car. This TB has less than 4k miles on it, but the electronics has about 30k miles on them. This will not be available until after the 18th where I still need it on the car.



Retail $150 (plus $150 core, shipping on your original plus $50 for powder coating or $350 up front cost)



SOLD!!!!!!!!!!




Headers: Sale pending

1.75" BBK long tube headers. These are an early pre-production version. They have bungs welded onto a runner on each side for A:F sensors if you want to run a dual band A:F gauge. I also have the Catted mid pipes for these. Where I was running these on my car with the blower, one of the cats melted the internals and it would be best if the buyer were to remove the internals. I also have off-road pipes in case you don't want to run cats. These are currently on the car and will not be available until after the 18th.



Retail $799 Asking $400 o.b.o. Sale pending...





Axle Back. Sale pending

JBA Axle Back exhaust. This will work with both the standard rear valence as well as the GM GFX rear valence. This is the 2.5" system that mates up to the factory H-pipe.



Retail $550 (JBA lists it for $775 but I've found it cheaper) Asking $300. Sale pending.....



When paired with the BBK headers my car put out over 125dB during multiple sound off competitions with the loudest being 131dB. If you want a loud and throaty sound, this is the combination that you want.





ZL1 Fuel Pump

I've run this pump for just under 10k miles. I'm converting to a dual pump setup to run E85 and this will not keep up. With Bosch 1000 injectors, it was able to keep up with 620rwhp without dropping pressure on a dynojet dyno (590rwhp on CMS's Mustang and Dyno Dynamics dyno's). I'm not sure if the float is needed for the new setup, but I don't believe it is.



ADM FPCM

If you are going to run the ZL1 pump, you have to have this FPCM in order to get the benefit of the pump. Both of these were installed together and will be sold as one unit.



SOLD!!!!



Spectre CAI



I had this powder coated black and it highlighted all the blemishes that were unseen in the tube prior to powder coating. If you want a CAI that works, but looks like its seen its better days, you can have it. I'm currently unable to find the filter, so you would need a 8-9" conical filter.



MISSING THE FILTER.......Keeping until it is located......


RX Catch can in Orange. SOLD!!!!!

Mounted to the car but never plumed. I do not have the vacuums hoses but you can get that at any auto parts store for $1.59 per foot. I want to say they came with automatic transmission line.





If you want it shipped, you will only be responsible for actual shipping charges from 92585 to you.



If you want multiple items, I'm open to a group discount.



Pic's of items currently in my garage will be posted shortly.


Sent from my iPhone using Tapatalk

[JT Camaro]

how could i say no to a free CAI. Pm sent!

[2010SSRSM6]

Originally Posted by JT Camaro

how could i say no to a free CAI. Pm sent!

Replied.


Sent from my iPhone using Tapatalk

[2010SSRSM6]

Picks of items in my garage will be up by Monday. Work has been a bit brutal this week.


Sent from my iPhone using Tapatalk

[foo.fighter]

oh I really wanna see the inferno orange tb! post pics of that when you can I am interested... and I can wait till 18th

[ccb1975]

Might be interested in headers

[2010SSRSM6]

Pics posted of the Vmax, BBK 95mm (w/Vmax electronics) and LT high flow cats.

You can see in the pic the HF cats will need to be gutted.


Sent from my iPhone using Tapatalk

[2010SSRSM6]

Originally Posted by foo.fighter

oh I really wanna see the inferno orange tb! post pics of that when you can I am interested... and I can wait till 18th

Posted

Originally Posted by ccb1975

Might be interested in headers

I'll be able to post pics as soon as they come off.



Sent from my iPhone using Tapatalk

[2010SSRSM6]

Added RX catch can.


Sent from my iPhone using Tapatalk

[Jfalkner94]

PM sent for catch can!

[2010SSRSM6]

Originally Posted by Jfalkner94

PM sent for catch can!

Replied


Sent from my iPhone using Tapatalk

[Keachj06]

if deal falls through with the catch can let me know im interested

[broke1LE]

I'm interested in the headers, and axleback as a package.

Sent from my SM-G900P using Tapatalk

[2010SSRSM6]

Originally Posted by Keachj06

if deal falls through with the catch can let me know im interested

Will do

Originally Posted by broke1LE

I'm interested in the headers, and axleback as a package.

Sent from my SM-G900P using Tapatalk

PM Sent



Sent from my iPhone using Tapatalk