Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Dynomax Exhaust
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Technical Camaro Topics > Cosmetics and Lighting Modification Discussions


Reply
 
Thread Tools
Old 09-16-2010, 08:29 PM   #1
LosingReality
 
LosingReality's Avatar
 
Drives: Camaro LS
Join Date: Apr 2010
Location: Columbus GA
Posts: 354
Installed the V6 Stillen splitter too!

Added the Stillen V6 Splitter. I like I even installed it without taking the front off too! It was alittle bit of a pain in the butt, but ive heard taking off the front is too. But i made it work and got it on there. The tape for the sides seem VERY sturdy, i know a few people have had an issue with the tape....I figured i would give it a go with the tape and if it comes loose, i will epoxy it in place.

The way i did it without taking the front of is i had it resting on some boxes that were just the right height to support it against the car. I removed the back side of the tape and slid it into place....It took alittle bit of making sure all the tape wasnt stuck on, until i knew it was in the right position so i could adjust it. Once it was in position, stuck it all down and good to go.

The tape seriously seems strong, ive put a good amount of weight on it, trying to take it off and it wont budge. I DID use dawn soap on those areas, about 5 or 6 times to make sure all the wax was off first though. We shall see how the tape holds up in the heat tomorrow though.

Onto the pics.








LosingReality is offline   Reply With Quote
Old 09-16-2010, 09:06 PM   #2
bossbunny
Mrs. Bunny to you
 
bossbunny's Avatar
 
Drives: The Sassiest V6 in the South!
Join Date: May 2009
Location: Cut 'N Shoot Texas
Posts: 24,454
I like!
bossbunny is offline   Reply With Quote
Old 09-16-2010, 09:08 PM   #3
2010 SSRS



 
2010 SSRS's Avatar
 
Drives: 3 V8 Camaros
Join Date: May 2009
Location: The Ocean State
Posts: 111,431
looks real good
__________________
Jannetty Racing JRE Street Package
2010 SSRS is offline   Reply With Quote
Old 09-16-2010, 09:08 PM   #4
orange10s.c.

 
orange10s.c.'s Avatar
 
Drives: IOM 2SS RS M6 sunroof
Join Date: Jul 2009
Location: panama city fl
Posts: 4,880
looks good.
orange10s.c. is offline   Reply With Quote
Old 09-16-2010, 11:05 PM   #5
CamaroCK
SoCal HT5
 
CamaroCK's Avatar
 
Drives: 2013 VR 2SS/RS
Join Date: May 2010
Location: Northridge, CA
Posts: 318
How much you get it for?
CamaroCK is offline   Reply With Quote
Old 09-17-2010, 12:27 AM   #6
cyberLS

 
cyberLS's Avatar
 
Drives: 2010 Cyber Grey LS
Join Date: Mar 2010
Location: Santa Clara
Posts: 2,218
looks real good i really need to get one
cyberLS is online now   Reply With Quote
Old 09-17-2010, 12:33 AM   #7
Dyk-NO
Trust me I'm a Scientist.
 
Drives: My wifey ;P
Join Date: Jun 2010
Location: Houston, TX
Posts: 1,099
It looks good don't paint it. It matches pretty well with your car together with the black outs!

and the item is not that expensive too, I think this will be my next mod
__________________
"From ZERO to a Tire-Burning HERO!"

Mods: RotoFab CAI, SW Headers, HiFlo Cats, Borla Atak Catback, Nightfury Cam, Ported Heads,Intake,TB, melling pump, Morosso Oil Separator.
Dyk-NO is offline   Reply With Quote
Old 09-17-2010, 12:51 AM   #8
jagan323
I have no life
 
jagan323's Avatar
 
Drives: 06' Subaru STI, ex-Camaro V6 LLT
Join Date: Apr 2010
Location: Top Gear Test Track
Posts: 3,190
Yeah the splitter looks good man! =D
__________________
jagan323 is offline   Reply With Quote
Old 09-17-2010, 01:40 AM   #9
SILVER BULLITT

 
Drives: 2010 SIM 2SS/RS MONSTER
Join Date: Aug 2009
Location: LOS ANGELES
Posts: 1,506
looks dope
__________________
HP MONSTER' SOUTHERN CALIFORNIA BUILT, LMR CAI, CUSTOM GRIND CAM, CUSTOM BUILT CNC PORTED AND POLISHED HEADS, FAST 102MM INTAKE MANIFOLD,ARH LONG TUBES AND HIGH FLOW CATS, BIGGER INJECTORS, VALVES SPRINGS RETAINERS, MGW SHORT SHIFTER, EIBACH SPRINGS, FACTORY CHROMED WHEELS, BLACKED OUT EMBLEMS, BLACKED OUT ROOF,BLACKED OUT MARKERS, 3.5 INCH ELECTRONIC CUTOUTS, FLOWMASTERS, ZEX WET 150 SHOT, FOR A GRAND TOTAL OF =630 REAR WHEEL TORQUE ,AND 600 REAR WHEEL HORSEPOWER
MY JOURNALhttp://www.camaro5.com/forums/showth...02#post2023802 SOON TWIN TURBO SETUP
SILVER BULLITT is offline   Reply With Quote
Old 09-17-2010, 05:22 AM   #10
LosingReality
 
LosingReality's Avatar
 
Drives: Camaro LS
Join Date: Apr 2010
Location: Columbus GA
Posts: 354
Thanks guys! Got it from the stillen website, $149, then they charge like 9 bucks handling fee. They say free shipping, but the 9 bucks is for handling. But hell, 9 bucks isnt that much.....the box it came in is rediculously huge.
LosingReality is offline   Reply With Quote
Old 09-17-2010, 06:29 AM   #11
BLACK10


 
BLACK10's Avatar
 
Drives: 2010 CAMARO. 10.04@133mph, 1.4 60'
Join Date: Jul 2009
Location: Lafayette, Louisiana
Posts: 4,550
nice
BLACK10 is offline   Reply With Quote
Old 09-17-2010, 01:55 PM   #12
Mach

 
Mach's Avatar
 
Drives: White M6 1LT RS
Join Date: Mar 2010
Location: Canton, MI
Posts: 1,676
You mentioned epoxying the splitter to the bumper if the double sided tape doesnt hold.... Don't do it!! The bumper is too flexible and epoxy is too hard... The bond will break.

The Splitter looks GREAT!!!!!! Goes well with the blacked out grill area.
__________________
Pfadt Sway Bars - FE3 Suspension - Barton Shifter - IdealG's Clutch Master Cylinder - Trifecta - Vmax TB - Vararam Intake - MACE 25mm Insulator - Plenum Insulator - Ported/Gasket Matched Intake Manifold - Rx Catchcan - AAC DRL's - 4 Pack Aux Gauges - Steering Controls - AAC Afterburners - DIY Led Sidemarkers - ZL1 Front End

Next mod: Done!
Mach is offline   Reply With Quote
Old 09-17-2010, 02:03 PM   #13
cowboy1948

 
cowboy1948's Avatar
 
Drives: 10 LT2/RS-08 SILVERADO-05 COBALT
Join Date: Jun 2009
Location: OHIO
Posts: 929
Cool

Quote:
Originally Posted by LosingReality View Post
Thanks guys! Got it from the stillen website, $149, then they charge like 9 bucks handling fee. They say free shipping, but the 9 bucks is for handling. But hell, 9 bucks isnt that much.....the box it came in is rediculously huge.
Could not find it on thier web site.
__________________

Retired
cowboy1948 is offline   Reply With Quote
Old 09-17-2010, 02:07 PM   #14
LosingReality
 
LosingReality's Avatar
 
Drives: Camaro LS
Join Date: Apr 2010
Location: Columbus GA
Posts: 354
Quote:
Originally Posted by Mach View Post
You mentioned epoxying the splitter to the bumper if the double sided tape doesnt hold.... Don't do it!! The bumper is too flexible and epoxy is too hard... The bond will break.

The Splitter looks GREAT!!!!!! Goes well with the blacked out grill area.

What do you suggest i use?
LosingReality is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Camaro Dove Tail Spoilers Compilation daphatgrant Cosmetics and Lighting Modification Discussions 449 03-05-2016 06:22 AM
***** RK Sport SS and V6 Body Kits On Sale ***** SicMSP Exterior Parts & Accessories 13 10-28-2010 04:36 PM
Solo Performance V6 Mach-XL (Manual) and Mach-XLT (Auto) Exhaust Kits GOINGSOLO2 V6 Bolt-Ons & Tunes 13 07-13-2010 01:28 PM
Airaid V6 Just Installed! faninc Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 94 12-17-2009 09:33 PM
Anyone with Stainless Works V6 Headers Installed? Abygale Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 19 10-15-2009 11:49 PM


All times are GMT -5. The time now is 07:45 PM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.