Check engine light - Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums

chevyss · 02-06-2011, 03:47 AM

My car has the check engine light on and I want to get it turned off. I installed ARH and CAI right after I got it and the light has been all the time since. I don't want to take it all off to get the light out. I'm going to sell or trade the car off and I don't want the light on. Thanks in advance for the help and advice.

Scott@Bjorn3D · 02-06-2011, 05:32 AM

Needs to be tuned out by a tuner.

Tampa Tuning · 02-06-2011, 06:11 AM

Might be your 02 sensor bank 2. Rear sensors. Just have the car tuned and you'll love the way it runs and wont want to sell it

2SSCAMARO · 02-06-2011, 06:59 AM

Quote:

Originally Posted by chevyss

My car has the check engine light on and I want to get it turned off. I installed ARH and CAI right after I got it and the light has been all the time since. I don't want to take it all off to get the light out. I'm going to sell or trade the car off and I don't want the light on. Thanks in advance for the help and advice.

You need to read out the codes stored in the ECM. Obviously one or more of the codes causing the CEL is related to the exhaust and CAI installation. The other issue is because you have driven the car so long with the CEL lighted, you don't know if there are other problems that need to be corrected. Again, first step is to get the codes read so you know what your dealing with. Post up the codes when you get them.

chevyss · 02-06-2011, 10:41 PM

Thanks all!!

2010 Indy Pace Car · 03-22-2011, 02:38 PM

If its a 01/01 sensor or a 02/01 sensor the issue is before the CATs. Not to worry though, hopefully. Chances are that the sensor(s) have gone bad due to the burn off of residure inside the headers during their initial firing. In other words, the residue that the headers had inside them for storage/shipping burnt off and coated the sensor tips. Try replacing them and you might be surprised to find that you can keep all of the emissions working properly, especially if they are checked in Washington!

If it is a xx/02 sensor it is after the CATS and, as stated above, you can tune them out as they do not have anything to do with the fuel/O2 mixture by the computer. It only reads the input for adjustments from the front O2 sensors.

Slowhawk · 03-22-2011, 08:05 PM

Needs a tune/tuner. I had a customer complain about the same thing. Had a shop do the headers and the light was on right after.Came to us a month later and on our first scan we found the pass. side 02 was junk from them torching it out of the old exhaust. That month he waited was gas washing the pass. side of the motor.

Carl6811 · 04-01-2011, 07:51 PM

I had same issue when I installed at cai, set of clear image long tubes and high flow cats....I tried the low-tech method and disconnected the battery at the positive terminal under the hood after I drove about 100 miles to see if the ecu would "learn" the changes, it didn't work. I then disconnected the battery in the trunk and after only 5 minutes reconnected it. The light went off, have not seen it since (about another 100 miles). I have done both normal driving and hard pulls to about 6100 rpm and so far, so good....

vart · 04-19-2011, 10:29 PM

installed my Volant cai last week. Then it snowed so I didn't get a chance to drive much since the night i installed it. Drove today finally and my CEL came on. Checked all connections and it seems pretty tight. I just unhooked my battery and I'll let you know in a half hour or so if that made the light disappear.

vart · 04-19-2011, 11:36 PM

It's gone!! Thanks for the tip.

slickmetal · 04-20-2011, 08:33 AM

Quote:

Originally Posted by vart

installed my Volant cai last week. Then it snowed so I didn't get a chance to drive much since the night i installed it. Drove today finally and my CEL came on. Checked all connections and it seems pretty tight. I just unhooked my battery and I'll let you know in a half hour or so if that made the light disappear.

If it went away with out someone using a scanner/OBDII Diag tool etc, it is still in memory in your ECU...have someone check it and see what CEL code you got and if its no biggy, have it cleared from memory.

slickmetal · 04-20-2011, 08:35 AM

Quote:

Originally Posted by Tampa Tuning

Might be your 02 sensor bank 2. Rear sensors. Just have the car tuned and you'll love the way it runs and wont want to sell it

I do believe this is the P1153 CEL code, correct?

For the OP, this code will need to be tuned out, and is the common CEL after headers/hi flos/CAI...(right?)

bmorecam · 04-20-2011, 09:39 PM

Quote:

Originally Posted by Tampa Tuning

Might be your 02 sensor bank 2. Rear sensors. Just have the car tuned and you'll love the way it runs and wont want to sell it

does having the rear bank cel due to long tube cause your car to run any different than if u was to tune it out? im asking because some say that its only a light and some say that your car will run rougher and slower.
I've been running with my cel for about a month but the only thing i notice is my car idling a little louder and rougher but i might just be hearing my long tube and no cats

02-06-2011, 03:47 AM	#1
chevyss SS/RS Drives: 2010 SS/RS IOM w/blk stripes A6 Join Date: Jun 2009 Location: Eastern Washington Posts: 816 View My Garage	Check engine light My car has the check engine light on and I want to get it turned off. I installed ARH and CAI right after I got it and the light has been all the time since. I don't want to take it all off to get the light out. I'm going to sell or trade the car off and I don't want the light on. Thanks in advance for the help and advice.

02-06-2011, 05:32 AM	#2
Scott@Bjorn3D Drives: Kami, 2013 2SS LS3 Luvin Join Date: Oct 2008 Location: Eufaula, Alabama Posts: 5,386	Needs to be tuned out by a tuner. __________________

02-06-2011, 06:11 AM	#3
Tampa Tuning Like us on Facebook! Drives: C5 corvette/ 2012Dodge hemi Charger Join Date: Oct 2010 Location: Tampa, Fl Posts: 1,656	Might be your 02 sensor bank 2. Rear sensors. Just have the car tuned and you'll love the way it runs and wont want to sell it __________________ Read these: http://www.camaro5.com/forums/showthread.php?t=197715 http://ls1tech.com/forums/florida-members/1575151-tampa-tuning-dyno-tuning-street-tuning.html

03-22-2011, 02:38 PM	#6
2010 Indy Pace Car NCCOA Ch 1 Drives: 2010 Camaro 2SS/RS - Z4Z # 44 Join Date: Feb 2011 Location: Fayetteville, NC Posts: 298 View My Garage	If its a 01/01 sensor or a 02/01 sensor the issue is before the CATs. Not to worry though, hopefully. Chances are that the sensor(s) have gone bad due to the burn off of residure inside the headers during their initial firing. In other words, the residue that the headers had inside them for storage/shipping burnt off and coated the sensor tips. Try replacing them and you might be surprised to find that you can keep all of the emissions working properly, especially if they are checked in Washington! If it is a xx/02 sensor it is after the CATS and, as stated above, you can tune them out as they do not have anything to do with the fuel/O2 mixture by the computer. It only reads the input for adjustments from the front O2 sensors. __________________ ... . ADM CAI,-ARH, JARHEADBOB and MAX, LINGEFELTER TB, SS CEK, JANNETTY RACING, RPM Motorsports

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Engine Misfire when cold, Check Engine Light	TooCool5	Camaro Issues / Problems \| Warranty Discussions \| TSB and Recalls	16	03-30-2011 10:26 AM
Acronyms?	KEEP RT	Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons	20	03-11-2011 08:57 PM
Check Engine Light	twnorman	Camaro Issues / Problems \| Warranty Discussions \| TSB and Recalls	3	01-23-2011 07:32 PM
Check Engine Light...	Missionboi	Camaro Issues / Problems \| Warranty Discussions \| TSB and Recalls	1	01-08-2011 01:02 AM
P0300 Misfire Code Help	black-knight	4th Generation Camaros	4	02-08-2010 01:45 PM

02-06-2011, 10:41 PM	#5
chevyss SS/RS Drives: 2010 SS/RS IOM w/blk stripes A6 Join Date: Jun 2009 Location: Eastern Washington Posts: 816 View My Garage	Thanks all!!

03-22-2011, 08:05 PM	#7
Slowhawk Account Suspended Drives: 1999 Trans Am Join Date: Jul 2009 Location: Bridgewater,Ma Posts: 1,271	Needs a tune/tuner. I had a customer complain about the same thing. Had a shop do the headers and the light was on right after.Came to us a month later and on our first scan we found the pass. side 02 was junk from them torching it out of the old exhaust. That month he waited was gas washing the pass. side of the motor.

04-01-2011, 07:51 PM	#8
Carl6811 Drives: 2011 CGM RS/2SS, 07 Pont. GXP Join Date: Aug 2010 Location: South Jersey Posts: 9	I had same issue when I installed at cai, set of clear image long tubes and high flow cats....I tried the low-tech method and disconnected the battery at the positive terminal under the hood after I drove about 100 miles to see if the ecu would "learn" the changes, it didn't work. I then disconnected the battery in the trunk and after only 5 minutes reconnected it. The light went off, have not seen it since (about another 100 miles). I have done both normal driving and hard pulls to about 6100 rpm and so far, so good....

04-19-2011, 10:29 PM	#9
vart Drives: 2010 2SS Join Date: Nov 2010 Location: Calgary, Alberta Posts: 155 View My Garage	installed my Volant cai last week. Then it snowed so I didn't get a chance to drive much since the night i installed it. Drove today finally and my CEL came on. Checked all connections and it seems pretty tight. I just unhooked my battery and I'll let you know in a half hour or so if that made the light disappear.

04-19-2011, 11:36 PM	#10
vart Drives: 2010 2SS Join Date: Nov 2010 Location: Calgary, Alberta Posts: 155 View My Garage	It's gone!! Thanks for the tip.