Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Vitesse Motorsports
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V6 LLT Engine, Exhaust, and Bolt-Ons


Reply
 
Thread Tools
Old 03-19-2011, 12:34 PM   #18
xpanda305x
Banned
 
Drives: Dark Knight
Join Date: Nov 2009
Location: Gunshine State
Posts: 3,152
i just blew on the maf as to clean some stuff and my filter looks ok?its fine. i disconnected the battery and re tighten everything!
xpanda305x is offline   Reply With Quote
Old 03-19-2011, 12:35 PM   #19
chozn4service
Five-O
 
chozn4service's Avatar
 
Drives: 2011 2SSRS A6 RJT
Join Date: Dec 2009
Location: +34° 55' 19.15", -117° 53' 22.43"
Posts: 2,753
I never called any names on brands, somone else did if you go back and look at the posts. I only made comment that Airaid never threw codes and that I wasn't calling any names. I think the original poster said something like Airaid or K&N but he wasn't sure and I for one would not have even said that much if I didn't know for sure. That's like telling someone something that I'm not even remotely sure on and then having them base their decision on what I said. I've learned in 30yrs of court testimony, if you don't know the answer to a question that is asked, be smart enough and professionally enough to say "I DON'T KNOW".
Airaid is not my product so its not mine to defend. Do I have one, yes I do. Do I like it? Yes I do. If another like Vararam comes through with their product and it proves to be better than what we all have chosen, I may make a change. JRE did the test and all were within a few HP of each other and Airaid was 2nd to InJen I believe but I've slept since then. I personally don't care for Injen install and replacing the fluid bottle and wheel well removal or whatever. My thing is, I'm not here to argue over anything that's not putting money in my pocket, making my monthly note on anything I own or trying to buy and I'm not got to go back and forth. Like I said, the man was talking codes, someone said Airaid and maybe K&N caused them and I was saying not so on Airaid. I consider the case closed and hope dude gets his issues resolved.

Peace and someone can hit the light switch on their way out cause I'm gone.
__________________
"Praise The Lowered"
SLP Catback Exhaust, CAI intake, ARH LT Headers, VMax Ported TB, BTR Stage II Cam, DSE lowering springs w/ZL1-1LE conversion. 450rwhp/423rwtq
chozn4service is offline   Reply With Quote
Old 03-19-2011, 12:39 PM   #20
xpanda305x
Banned
 
Drives: Dark Knight
Join Date: Nov 2009
Location: Gunshine State
Posts: 3,152
i have K&N intake :( sorry for the fight? and it went away for now :( lets see how long it last. i emailed K&N tho.
xpanda305x is offline   Reply With Quote
Old 03-19-2011, 02:37 PM   #21
usa1camaro1969
Back on the dino-juice
 
usa1camaro1969's Avatar
 
Drives: '10 LS + a few more
Join Date: May 2010
Location: Texas
Posts: 1,640
Good luck, both with the CEL and if it becomes an issue you can then have it documented with K&N.
__________________
I wake up in the morning and I piss excellence.
-Ricky Bobby
America is all about speed. Hot, nasty, badass speed. -Eleanor Roosevelt, 1936
usa1camaro1969 is offline   Reply With Quote
Old 03-19-2011, 03:55 PM   #22
xpanda305x
Banned
 
Drives: Dark Knight
Join Date: Nov 2009
Location: Gunshine State
Posts: 3,152
well its gone for now...might come back? i tighten everything! and got a oil change
xpanda305x is offline   Reply With Quote
Old 03-19-2011, 04:24 PM   #23
willyd
 
willyd's Avatar
 
Drives: Victory Red 2011 Chevy Camaro 2LTRS
Join Date: Mar 2011
Location: SoCal
Posts: 204
Wow this got a little heated. I was just simply forwarding along the dangers of using the MAF cleaner, and you're right if you're careful using it you should be fine. But of course GM doesn't recommend using it. If there was oil that got on the MAF, then you may have to replace it ultimately...and if that ends up being the case, then you would need verfication that it was oil build up caused by the intake. If you receive said verficiation via professional or even detailed and documented personal evalutation, then you're well within your rights to request K&N refund the cost of any repair...That's a lot of ifs, I was just trying to give the guy options in case that happened to be the case is all.
__________________
Installed: DT Shorties, Trifecta Tune, Injen Short Ram Intake, GM victory red engine cover, RX Catchcan, AEM Air Fuel and Boost gauge, Transmission cooler w/braided stainless lines
willyd is offline   Reply With Quote
Old 03-30-2013, 10:29 AM   #24
hb35man
 
hb35man's Avatar
 
Drives: 2010 Camaro 1LT Aqua Blue Metallic
Join Date: Dec 2009
Location: Algona Washington
Posts: 316
read through this because last week I installed my K&N system and it was great.........until last night. CEL came on. Did you guys have to have someone clear the code or is there a do it your self way?
hb35man is offline   Reply With Quote
Old 03-30-2013, 10:56 AM   #25
Can't_C_Me
Don't Sleep on My V6
 
Can't_C_Me's Avatar
 
Drives: 2016 C7 1LT
Join Date: Dec 2010
Location: Oxford, GA
Posts: 3,594
Like said before clean your MAF with the cleaner. Most likely it got it dirty by way of the intake. The MAF cleaner won't damage anything as I use to use it weekly when I had my oil seal on my turbos blown. Still working great now.
__________________
Can't_C_Me is offline   Reply With Quote
Old 03-30-2013, 10:59 AM   #26
hb35man
 
hb35man's Avatar
 
Drives: 2010 Camaro 1LT Aqua Blue Metallic
Join Date: Dec 2009
Location: Algona Washington
Posts: 316
Thanks Cant_C_Me. is there a quick easy way to clear the code?
hb35man is offline   Reply With Quote
Old 03-30-2013, 01:42 PM   #27
hb35man
 
hb35man's Avatar
 
Drives: 2010 Camaro 1LT Aqua Blue Metallic
Join Date: Dec 2009
Location: Algona Washington
Posts: 316
Went to Autozone........bought a scan tool and a can of MAF cleaner.......started on my way home......looked down and......NO CEL!!??
hb35man is offline   Reply With Quote
Old 03-30-2013, 07:33 PM   #28
Can't_C_Me
Don't Sleep on My V6
 
Can't_C_Me's Avatar
 
Drives: 2016 C7 1LT
Join Date: Dec 2010
Location: Oxford, GA
Posts: 3,594
Quote:
Originally Posted by hb35man View Post
Thanks Cant_C_Me. is there a quick easy way to clear the code?
Quote:
Originally Posted by hb35man View Post
Went to Autozone........bought a scan tool and a can of MAF cleaner.......started on my way home......looked down and......NO CEL!!??
__________________
Can't_C_Me is offline   Reply With Quote
Old 03-30-2013, 08:48 PM   #29
hb35man
 
hb35man's Avatar
 
Drives: 2010 Camaro 1LT Aqua Blue Metallic
Join Date: Dec 2009
Location: Algona Washington
Posts: 316
Quote:
Originally Posted by Can't_C_Me View Post
Actually I didn't think threatening to trade it in would scare it into submission
hb35man is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Diablosport Predator Tune + JBA 2.5" high flow cats = CEL P0430 The Stig Tuning / Diagnostics -- engine and transmission 17 11-12-2011 08:44 AM
Cure for the CEL ?! 5thGENv6 Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 27 02-12-2011 08:13 AM
One possible solution to CEL P0430 w/ JBA midpipes Goliath Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 0 01-10-2011 08:55 PM
Another LT Headers and CEL for Emissions kauffjd3 Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 7 10-29-2010 03:54 PM
Clearing a CEL jtzako 5th Gen Camaro SS LS LT General Discussions 8 07-09-2010 02:37 PM


All times are GMT -5. The time now is 01:22 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.