Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
JDP Motorsports
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V6 LLT Engine, Exhaust, and Bolt-Ons

Camaro V6 LLT Engine, Exhaust, and Bolt-Ons Bolt-Ons | Intakes | Exhaust

Reply
 
Thread Tools
Old 05-26-2011, 12:06 PM   #26
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Quote:
Originally Posted by KMPrenger View Post
Aww heck, your even running the stock intake and still made that power? heck...your doing just fine!
and thats with 90 degree humid weather we had yesterday and almost all week. Today we are reaching 95. This hot weather is killing me.
Im sure 93 gas and running catless had alot to do with it too, and vince did say that adding long tube with his new tune can see bigger gains.
bmorecam is offline   Reply With Quote
Old 05-26-2011, 12:10 PM   #27
GretchenGotGrowl


 
GretchenGotGrowl's Avatar
 
Drives: `12 LFX/`11 EB F-150/`13 Sonic RS
Join Date: Sep 2010
Location: Little Rock, AR
Posts: 4,948
It would be fantastic if you were the first NA car to 300 RWHP, but I think you will still be a little shy even with the E85 and a CAI. However, PLEASE prove me wrong!

Good luck man, this is going to be very interesting.
__________________
EFR Twin Turbo LFX-GPI Tune-ZL1 fuel pump-10:1 CR forged pistons-3.45 gear-Meth Injection-BMR Trailing Arms, Bushings & Sway Bars-CircleD 4000 Stall-GPI Fuel Enrichment System
647 RWHP & 726 RWTQ @18.5 psi on 93 Octane (locked converter)
1/8 mile -- 7.158 @ 102.10 (20psi); old build
Build Thread
GretchenGotGrowl is offline   Reply With Quote
Old 05-26-2011, 12:24 PM   #28
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Quote:
Originally Posted by GretchenGotGrowl View Post
It would be fantastic if you were the first NA car to 300 RWHP, but I think you will still be a little shy even with the E85 and a CAI. However, PLEASE prove me wrong!

Good luck man, this is going to be very interesting.
Very interesting indeed! vince stated that his vette got 20hp just with a tune. He think our LLT will be very interesting with e85 due to simple fact that we have direct injection on our side and we naturally have high compression which is a big plus for e85.
E85 love boost and high compression. Mix those two into factor and peoples are seeing numbers and timing that you will never see with regular gasoline.
Even if I can see minimum of 20hp like on vince car than I am positive that I can hit 300whp with vararam.
Who knows, we might see even more. It all depends how far it will go before knocking but with the natural octane rating of 105+ and its cooling nature of e85 I am very optimistic
bmorecam is offline   Reply With Quote
Old 05-26-2011, 12:34 PM   #29
TJ91
:chevy:
 
TJ91's Avatar
 
Drives: 2LT/RS
Join Date: Jun 2008
Location: Toronto
Posts: 12,474
get rid of your 93 octane already lol
Hope you get stuck in a traffic jam
Sorry I have to, im too excited for this! LOL
__________________
CAMARO
Consult your doctor before taking Camaro
Side effects include Sudden increase in Heart Rate, Insomnia and occasional hallucinations
If you experience Permagrin exceeding 4 hours after taking Camaro, seek immediate Camaro5 Help
CAMARO Bringing excitment back into the Garage
TJ91 is offline   Reply With Quote
Old 05-26-2011, 01:03 PM   #30
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
lol TJ.. This is one time that I wish my car got bad gas mileage but I dont mind taking it a little slow today because its like almost 100 degrees outside enough to make your head hurt. Im trying to stay in as much as I can today plus I am mostly at work all day so I really dont have a chance to drive out my gas anyway. I just checked my miles to go and it say 55 miles so by tomorrow I should be ready to put in first tank of e85 and load the tune.
Just hope that this go well because if it does than 300whp should be a piece of cake with our LLT assuming you have access to e85. Lucky for me I live and work around plenty of e85 station.
bmorecam is offline   Reply With Quote
Old 05-26-2011, 01:26 PM   #31
PoorMansCamaro



 
PoorMansCamaro's Avatar
 
Drives: Really Slow
Join Date: Apr 2010
Location: Las Vegas
Posts: 51,721
do you have a stock tune in your car now?
__________________
PoorMansCamaro is offline   Reply With Quote
Old 05-26-2011, 02:19 PM   #32
ROD1
Back to the hunt....
 
ROD1's Avatar
 
Drives: 2010 Camaro RS V6 #1301 DOB 3/23/09
Join Date: Aug 2009
Location: Ithaca NY
Posts: 2,561
Quote:
Originally Posted by bmorecam View Post
kmprenger you are right. For some reason I thought that our stock v6 dyno around 260hp.
260 for manuals and 245-250 for autos.
ROD1 is offline   Reply With Quote
Old 05-26-2011, 02:41 PM   #33
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Quote:
Originally Posted by PoorMansCamaro View Post
do you have a stock tune in your car now?
I have the regular gas tune in my car now.

Quote:
Originally Posted by ROD1 View Post
260 for manuals and 245-250 for autos.
That is defenitely possible rod. Ronslo who's doing testing for VR is seeing 245-250 with manual stock and I think he was even seeing less than that while the car was newer if I can remember correctly. so I guess one cant really take these numbers too seriously. It make sense that dyno is only good to figure out what we made and what we lost on the same dyno, same situation, same car.

Plus vince said that others was seeing less than 260whp with the old tune and with the same level of mods as mine. Interesting.
bmorecam is offline   Reply With Quote
Old 05-26-2011, 02:47 PM   #34
PoorMansCamaro



 
PoorMansCamaro's Avatar
 
Drives: Really Slow
Join Date: Apr 2010
Location: Las Vegas
Posts: 51,721
Quote:
Originally Posted by bmorecam View Post
I have the regular gas tune in my car now.
so you did this dyno with the new tune with the 13hp increase?

as i stated, i had 270 with my mods with no tune. so if you put the injen on, you would probably see over 280whp. and who knows with the vararam. good luck!
__________________
PoorMansCamaro is offline   Reply With Quote
Old 05-26-2011, 02:49 PM   #35
HopeRidesAlone

 
HopeRidesAlone's Avatar
 
Drives: 2010 Camaro Black 2SS/RS
Join Date: Mar 2010
Location: Maryland
Posts: 832
Hey Bmore what dyno shop did you goto i live up in harford and was wondering about a good place to go
__________________
2010 Black 2LT/RS - Injen CAI, ARK DTS Catback Polished Tips, OBX LT Headers, Lowered on Eibach, 3/8 blackiceolator, Trifecta Tuned.- Totaled 3/10/13

2010 Black 2SS/RS - Feesler side skirt, Feesler Spoiler, Feesler carbon fiber bowties, H&R Lowering Springs.
HopeRidesAlone is offline   Reply With Quote
Old 05-26-2011, 03:51 PM   #36
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Quote:
Originally Posted by HopeRidesAlone View Post
Hey Bmore what dyno shop did you goto i live up in harford and was wondering about a good place to go
I went to SRT, they are known in the lexus community with the fastest lexus is300 in the world. They are located in beltsville pg county.
Is your car stock or do you have any mods? I wish I could find a stock car to get some dyno number there.

poorman, 280whp would of been def possible with injen, and I think 275whp and even more could of been possible if the sun was not beaming at 90 degrees even with my current mods.
I also forgot to mention that my car was actually very sluggish when I went in and actually had emailed vince about it a day before.
300whp all n/a for our LLT is only right around the corner. I can feel it coming really soon
bmorecam is offline   Reply With Quote
Old 05-26-2011, 04:46 PM   #37
TJ91
:chevy:
 
TJ91's Avatar
 
Drives: 2LT/RS
Join Date: Jun 2008
Location: Toronto
Posts: 12,474
Quote:
Originally Posted by bmorecam View Post
lol TJ.. This is one time that I wish my car got bad gas mileage but I dont mind taking it a little slow today because its like almost 100 degrees outside enough to make your head hurt. Im trying to stay in as much as I can today plus I am mostly at work all day so I really dont have a chance to drive out my gas anyway. I just checked my miles to go and it say 55 miles so by tomorrow I should be ready to put in first tank of e85 and load the tune.
Just hope that this go well because if it does than 300whp should be a piece of cake with our LLT assuming you have access to e85. Lucky for me I live and work around plenty of e85 station.
lol sounds good man. Im soo stoked for this.
Only problem is ive been on the hunt for E85 here and cant find any. but the search continues. I want 300rwhp!!
Thanks for testing this though man! Cant wait to see what our LLTs can do
On three Team LLT

1

2

3

TEAM LLT
__________________
CAMARO
Consult your doctor before taking Camaro
Side effects include Sudden increase in Heart Rate, Insomnia and occasional hallucinations
If you experience Permagrin exceeding 4 hours after taking Camaro, seek immediate Camaro5 Help
CAMARO Bringing excitment back into the Garage
TJ91 is offline   Reply With Quote
Old 05-26-2011, 06:39 PM   #38
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Questions about e85? how much gain to expect on n/a and turbo cars? is it safe or is it corrosive? If you plan to run e85 in the near future you might want to take some time to read over. I seen alot of articles on e85 but this seem most comprehensive and its from my old forum nasioc.

Part 1
Introduction to my experiment with E85 circa 2004

This is a summary of past posts from various forum discussions

I have been running a high ethanol fuel blend in my WRX for nearly 2 years now, with no problems traceable to the fuel. The car really likes the high alcohol blend, with an obvious improvement in performance comparable to high octane so called "race fuels".

The Stock WRX ECU can handle up to approximately 33% E-85, by volume before you get a check engine light for "too lean" due to the fuel trims being pushed to the max rich settings. Add just a bit of pump premium and the CEL will clear.

I recently shifted to STi 550 injectors without any special changes in the engine management. Due to the cars larger injectors the car now prefers a higher blend. I am now running about 95% E-85, but have run the car on blends as low as about 30% E-85 without any serious problems. At lower blends the car has some surging due to the over size injectors at higher throttle settings, but can be easily driven as a daily driver if you stay out of the >60% throttle position transition to open loop.

The one problem is that currently E-85 sites are a little difficult to find, but the more of it we use the more available it will become.

The folks backing E-85 production are pushing as hard as they can to get stations to make it available, but its a slow process. They need customers to start asking station owners if they plan on carrying it to motivate stations to add a pump/tank.
There are currently dozens of FFV's out there that are designed to run on the stuff if folks can find a place to buy it. Simple way to drastically reduce oil demand as well, and put money in our economy instead of some other countries coffers.

I currently drive 20 miles each way to get to the nearest E-85 stations, but it is still a good deal as I am paying $1.59.9 / gal for the E-85, vs about $2.05.9 / gal for premium. ( some E-85 vendors charge at a premium fuel rate of about $2.00/gal)

With the added octane of the E-85 you can actually splash blend it with mid grade gasoline with out problems.

When I suspect it will be difficult to locate E-85 from the pump I just make a point of topping off the tank before it drops below 3/4 full. This keeps the ethanol blend up to a high enough level to avoid any drivability issues with my oversize injectors.

Is the WRX warrantied to run on E85 ?
NO it is not, but my experience shows its not a major issue either.

I think it is important to note that they don't recommend greater than 10% ethanol, ie they warranty the car will run fine with up to 10% ethanol but greater than that your on your own. But they do not say you should avoid higher blends of ethanol and other tests have shown modern cars can run on upto about 30% blends with no problem.

They do specifically mention that methanol is not to be used over 5% concentration, and that is due to corrosion issues with methanol, which is Much Much more prone to corrosion than ethanol.

So far I have seen no "real" problems with the E-85. There are two minor CEL issues.

1 If your running over 35% on a stock ECU and fuel injectors you will push the fuel trims to full rich and get a "too lean" CEL.

(edit 10/02/2005 --- emission CEL has not re-appeared in quite a long time. I am beginning to suspect it was due to a loose vacuum hose resulting from the injector upgrade that got fixed as I was working on other things )

As mentioned above any "damage" should be easily remedied, ie replacing a hose, or some O rings, possibly changing to a different fuel pump. It is very difficult to predict long term corrosion, or materials compatibility so I've decided to bite the bullet and be the test dummy and see what if anything breaks.

Based on my tests, the short term conclusion is you can run concentrations of >10% fuel ethanol for periods in execess of 1 year with no detectable damage. We'll just have to see how things go in another year or so.

Hopefully this winter I'll get the time to pull the fuel pump and look over the interior of the fuel tank to see how its doing.

What is the history of large scale conversions to high ethanol fuels

When Brazil began making a wholesale conversion to high ethanol fuels back in the late 70's following the energy crisis, they made several studies on the ability of normal cars to run ethanol blends. They found that the cars of that period could run up to about 22% blends on the stock system with no problems, which is why they settled on a 20% blend as one of the fuels available. The issue was one of control authority of the ECU to compensate for the leaner mixture. Some could handle more than others. As I stated, it appears the stock ECU on the 2002 WRX is good up till about a 33% - 35% blend.

During the 70's and 80's when oxygenated fuels and "gasahol" first saw wide use here in the U.S. there WERE fuel component compatibility problems. My 1969 VW fuel lines really didn't like the ethanol and began to leak like a sieve, some carburetor needle valves softened, some carburetor floats would soak up the ethanol and get too heavy to function as a float. There were lots of problems with clogged fuel filters on cars that had been running on gasoline only for decades and had lots of varnish build up in the fuel system. The ethanol in gasohol was a very efficient fuel system cleaner and all that crud got carried to the fuel filters. Once the fuel filters were replaced those problems disappeared.

At that time All the auto manufactures moved to ethanol compatible fuel line components, ie. o rings, rubber hose etc. They warranty that they are good to 10% but my experience shows they are satisfactory to much higher concentrations. The VW showed its compatibility problem in a matter of months after we went to ethanol blended oxygenated fuel here in Denver. Engineers typically don't solve a compatibility problem by making the new component "sorta compatible" they change compounds to materials that are not effected by the chemical in question.

The Denver area has been using ethanol oxygenated fuels (ranging from 5% - 10%) concentration for over 30 years. Every modern car works just fine with these low ethanol blended fuels. Rubber hoses and O rings last for the life of the car.


The electrical conductivity issue is not significant in the case of ethanol. It is detectable with a dialectic constant tester. It DOES become a significant issue with methanol blends which is why methanol blended fuel is so aggressively corrosive. The main issue with methanol is it aggressively attacks certain metals like magnesium and zinc. One of the reasons everyone is looking at ethanol is the 30+ years of successful use of high ethanol fuel blends in Brazil and low ethanol blends here in the U.S. with essentially zero problems after they changed fuel line and O ring and seal materials in the fuel system.

Dialectic Constants
Gasoline 2.2
Ethanol 24
Methanol 33.6
Water 48 - 88

Keep in mind that absolutely pure water is a good enough insulator it is used to cool electronic components. It does not become an effective conductor until is dissolves minerals that act as charge carriers (electrolytes).


Will my O2 sensor work with E85 and high ethanol blends?
The O2 sensor is not an issue, all it cares about is if your at stoich combustion at low throttle settings, it doesn't much care how you get there, so no need to change it.

Air-fuel ration: http://en.wikipedia.org/wiki/Air-fuel_ratio
Oxygen Sensor: http://en.wikipedia.org/wiki/Oxygen_sensor

What about the evaporative emissions system in my car

The higher vapor pressure of ethanol gasoline blends is not ideal for the evaporative emissions system and the vapor recovery canister. For full emissions compliance these will need to be modified. Currently there are no kits available to upgrade this part of the emissions system.

As I mentioned above the only -- real -- problem so far is simply some nusince CELs.
"too lean" if your over 30%+ on the stock injectors

If your emissions test requires no CELs present, you simply need to go to a lower ethanol fuel blend for a while to allow that nuisance CEL to clear, and the dash warning light to go off.


what would be needed for a complete conversion kit to run 100% ethanol fuel


For full conversion to alcohol fuels the change list typically looks something like:


1. Go to an compatable fuel pump (walbro 255 l/h pumps seem to work well with E85)
2. Replace fuel lines with alcohol compatible lines. (not needed on WRX based on current experience)
3. Possibly replace filter (not needed on WRX based on current experience).
4. Replace injectors with large enough ones to feed proper fueling. (+30% flow over stock)
5. Replace injector/FPR o-rings with compatible o-rings... viton maybe? (not needed on WRX based on current experience)
6. Add a spark/flash suppressor to the fuel tank inlet tube. (does not appear to be a significant hazard based on current experimenter experience)
7. Ensure the fuel tank material is completely compatible with alcohol. (not needed on WRX based on current experience)
8. Reflash or other engine management option for ideal tune to use E85's capability (optional at low to moderate boost)


With ethanol on the WRX, you only need (according to my current experience base) is numbers 4, 8.

(edited to remove comments about emissions CEL which proved to be due to other causes and has never returned)

What about fuel system corrosion?
Corrosion does not appear to be an issue with modern OBDII cars. They are all certified by the manufactures to be safe to use on 10% ethanol fuel blends, and industry insiders say they are safe for much higher percentages. You don't install components that are "sorta safe" with a chemical, you put in a fuel hose etc. that is ethanol safe for concentrations well above what you expect to use. Not to mention that folks have been talking for years about raising the ethanol level to 20% or more.

Occasional use would be no problem at all based on my experience. I have never cut open the fuel filter (still have the OEM filter in place) I'll open it when I replace it. I want to put enough time on it to have conclusive evidence if there are problems.
(edit circa 2007 I cut open a fuel line and it looked like new, not changes or damage on stock rubber fuel lines in 2002 WRX)

The engine is not an issue with either, WI using a water alcohol mix or straight alcohol injection. In those systems alcohol and water are not used in significant quantity or for long duration. The Buick GN folks and lots of folks in the DSM crowd have done it for literally decades with no problems for the engine.

Many years ago there were studies that indicated engines that ran on alcohol ALONE as a fuel, had issues with lubrication and valve seat wear. Keep in mind, those studies were done a long time ago, when engine oils were much less sophisticated than they are now, and some engine manufactures in the 1940's,1950' and 1960's made stupid engineering decisions and did not use hard valve seat inserts like stellite in the cylinder heads. This resulted in valve seat recession problems if you did not have lead additives in the fuel to protect the valve seats.

What about oil contamination?
Modern lubricants, especially the synthetic oils are much much different than the oils used during those studies, and modern engines run at higher temperatures today which will quickly boil any traces of alcohol out of the oil.
In cold weather I run an 180 deg thermostat to assist quick warmup I have left it in during this past summer and so far the engine has no heating issues with the 180 thermostat on the E85 fuel.
(edit experience shows modern synthetic oils work very well with E85)

Is Ethanol less corrosive than Methanol?
Methanol is much more corrosive than ethanol. It attacks certain soft metals that are not much used in modern fuel systems. Years ago, the carburetors were made of un-anodized aluminum and if methanol fuel was used, you had major problems with electrolytic corrosion between the aluminum and copper components used in the fuel system, since they were in continous contact.

That sort of corrosion only occurs when you have a current path between the dissimilar metals AND, a conductive path through the fluid in the system.

In Brazil where they have run high ethanol fuels since 1939, they found that to convert older cars designed for gasoline, long before ethanol blends were common, needed several changes to convert the cars over. This led to changes in valve materials, piston rings choices, nickel plating of the fuel tanks etc.

Modern cars in the U.S. are designed for use with ethanol up to 10% concentration in the fuel. That has led to several changes in component materials over the last 30 years that the U.S. has used ethanol enhanced fuels. All modern fuel lines and such are designed with the expectation that some ethanol will be in the fuel.


My experiment is an intentional effort to push the envelope and see what happens. Over the last 2 years I have run high ethanol fuels ( normal pump fuel here in Colorado contains up to 10% ethanol anyway) for months at a time.

At mixtures below 33% by volume of alcohol ( about 39% E-85 by volume) I had absolutely no problems of any kind. At higher mixtures > 33% alcohol, I got a nuisance CEL for too lean which could be eliminated by added gasoline to the mix or as I have recently increased the injector size. (Increasing fuel pressure would also increase the effective size of the injectors).

The only issue with near 100% E-85, is the car starts a little harder in cold weather. When it gets very cold I drop the mixture to about 80% or so to solve that by adding about 2 gallons of gasoline to the tank of E-85.

I have done no oil analysis at this point, walbro 255l/h fuel pump and 550 injectors show no signs of problems to date.

Larry
(last updated 6/10/08)

* Registered users of the site do not see these ads.

Last edited by hotrod; 07-02-2008 at 04:11 AM.

hotrodView Public ProfileVisit hotrod's homepage!Find More Posts by hotrod
07-08-2005, 10:53 PM #2 hotrod
Scooby Specialist

Member#: 14141
Join Date: Jan 2002
Location: 13.239@102.85 @ 5800 ft on 13T
Vehicle:
2002 Impreza WRX
e85forum.net





Part 2
Where can I buy E85?

Distribution is currently a problem, it is most available in the mid western states, but there is a concerted effort to get an ethanol fueling infrastructure built, it just takes time, and recognition by the gasoline vendors that there is a market. Marathon oil has already added E85 to their formal product line so things are moving in that direction.

Current high fuel prices can only help that process, as will lots of people calling up gas stations and asking them when they plan on pumping E85 for FFV's.

E85 already contains inhibitors and such to minimize corrosion, and most of the problems with ethanol usage were solved 20 years ago when most of the country moved to ethanol addition to gasoline following the oil crisis in 1973 and high oil prices that continued up until 1981.

Where can I buy E85
For information on distribution points check out:
http://afdcmap2.nrel.gov/locator/FindPane.asp



How about fuel mixtures for E85 what is needed ?

The one interesting thing to note is that the stock pig rich mixtures at WOT on the stock ECU of the WRX are very close to max power mixtures on E85 blends. If you play with the blending ratio to find your magic number you can take advantage of this by giving the car a fuel blend that is max power rich at stock ECU WOT mixtures. *** just take your time and work up the blend slowly ***

After a few folks have dyno runs on various blends we can probably pick out a "best starting point" blend that will get you very close. We could also work out the other supporting mods to make best use of E85 for minimum cost.

It basically takes about a +30% increase in fuel flow to get the same equivalent mixture with E85 that you had with gasoline.

For example an adjustable fuel pressure regulator can increase your effective injector flow to partially compensate for the fuel changes.

As mentioned above, lean is still a bad thing, and with alcohol fuels due to the higher power levels a serious leanout is more lethal. With conservative mixtures alcohol actually burns so cool that on E85 FFV there is some concern about getting the cat to light off.

If you sneak up on a fuel blend slowly you should be just fine. I would venture to say for the near stock folks, up to 30% is probably safe as long as you give the ECU a few miles to make the major part of the fuel trim accomodation before you start beating on the car. You'll know when the ECU starts to get happy as the midrange torque is noticably better.

I also strongly suspect that a well tuned car with no cats can probably pass the emissions sniff test on high E85 blends.


How does ignition timing change on E85 ?

Timing on ethanol blends will not change very much. MBT timing for both gasoline and E85 are very nearly the same at light to moderate engine loads. At high engine load the E85 will want just slightly more advance. The big difference will be fuel/air mixture. The E85 will give improved torque with much richer mixtures than gasoline. Both gasoline and E85 will give best thermal effeciency at about 15% rich of stoich, so the equivalent of 12.78:1 on gasoline would be about 8.5:1 on E85, but E85 will continue to give better torque numbers up to about +40% rich of stoich or 7:1 mixtures, so on a utec you would want to richen up your WOT high load cells and add a tweak of timing to get the most out of E85 from what I've read.

Quote:
Are you sure you don't mean that E85 will allow more advance?

Just passing on what I've found in the various sources. Logically you are correct, but one source says simply that MBT timing is the same for E85 and gasoline, and another report says at low loads the E85 and gasoline like the same MBT timing but at high loads MBT timing for the E85 is slightly more advance.

I suspect this is due to them not running ideal max power mixtures but cannot confirm it. Burn speed for E85 changes quite a bit with mixture, so if they were just a little bit lean or rich of ideal the burn rate would be lower.

Lots and lots of variables not well covered in some of the sources and in general they are focusing on emissions issues not max power torque so that would incline them to use less than best power timing advance. In a couple of the reports they also had limited control authority over timing and may not have explored the extremes very thoroughly.

what data is available on combustion speed for E85?
Just about a year ago (2003), I was finding conflicting information on alcohol fuel burn speeds and contacted The National Renewable Energy Lab here in Denver, they did a search and could only find a couple of references on it, one that showed ethanol fuels burn faster, so the literature is not very rich in data on the subject. Most reports are not entirely applicable to our needs like tests on lawnmower engines and alcohol fuels have some significant limitations

Still digging for info but that is my best information at the present time.

The report that mentioned the slight increased advance requirement on heavy load E85 fuels was :

"Final Report Control of Exhaust Emissions from Small Engines Using E-10 and E-85 Fuels"
http://www.michigan.gov/cis/0,1607,7...0064--,00.html
http://www.michigan.gov/documents/CI...E-_87915_7.pdf


On page 12 it says :
"Tests were conducted to assess the impact of MBT ignition timing on fuel economy and exhaust emissions. The spark timing was varied until the least advanced timing was achieved for the maximum torque for a given setting of the engine throttle. The A/F ratio was adjusted to achieve near stoichiometric operation. ... " The MBT timing for E-85 fuel was a few crank angle degrees advances compared to E-0 fuel when the engine was delivering high loads, typically 100 - 75%. Not much difference was observed at lower engine loads."

I'm assuming that this explains the timing change as they were using what would be closed loop fuel mixtures on the WRX. So in load cells that would continue to use closed loop fueling you would want to have slightly more ignition timing than you would with gasoline. In the case of WOT open loop fueling where your running a max power rich fuel mixture, I very strongly suspect the fuel burn speed would be noticably faster, and you would use less ignition advance than on gasoline and reap the benefit of less negative work on the late stages of the compression / early period of combustion prior to TDC.

In a power point presentation presented by the EPA at the SAE Government and Industry Meeting in Washington D.C. on May 13, 2003 titled:

"Ethanol-Gasoline Blends: Fuel Economy and Emissions Benefits"

http://www.epa.gov/otaq/presentation...mjb-051303.pdf

On page 9 of the presentation is a nice chart comparing laminar burn speeds of gasoline and Ethanol.

It shows the following burn speeds:

Mixture fuel/air---- 1:1 ------------ 1.1:1

Gasoline --------- 26 cm/sec ------- 30 cm/sec (max about 31 cm/sec)
Ethanol ---------- 41 cm/sec ------- 45 cm/sec (max value)

Clearly at +10% - +15% rich mixtures where ethanol shows max thermal efficiency it burns significantly faster than gasoline. Which could be quite important to a very over square bore engine like ours!!


what is the ideal fuel air mixture for E85

If you are tuning with a wideband O2 sensor you will want to switch it to Lambda mode to get valid fuel air mixtures with blended fuels. If you can only get gasoline AFR's, simply divide the gasoline AFR's by 1.5 to get the true AFR for 100% E85. If running a partial mixture you can make proportional changes based on the percentage of E85 in the mix.

Here are some comparisons of stoichiometric fuel mixtures for different fuel blends:
======== stoichiometric AFR ===== max power rich AFR
Gasoline ---------- 14.7:1 -------------------12.5
100% E-85 ------- 9.73-9.8:1 ------------- ~ 9:1 - 8:1
100% fuel ethanol - 9:1 ------------------- ~ 7.2:1

One source specifies that the proper fuel tune (stoich) for a VW Golf running 22% ethanol was 12.7:1 (this reference was probably from the Brazil tests)

Ethanol reaches max torque at richer mixtures than gasoline will.
Using a 99% ethanol mixture MEP increases with mixtures up to 40% excess fuel where with gasoline MEP is reached near 20% excess fuel. Over all thermal efficiency for both gasoline and ethanol is reached near 15% excess fuel.

E85 burns faster than gasoline at best mixtures so it is an inherently more effecient fuel. It also produces more exhaust gas for a give weight of fuel air mix giving higher average cylinder pressures inspite of lower EGT's. With streight E85 in a properly tuned car its good for about +5% power / torque increase. I suspect on a turbocharged car the benefit is larger.

My source lists stoich for E85 as 9.8:1 ( "Burn rates and emissions from ethanol gasoline blends" )
http://www.engin.umd.umich.edu/resea...5-2004.doc.pdf

Here's a little reference chart I whipped up when I was working out my dyno numbers.

Code:
Fuel AFRst FARst Equivalence Lambda ---- ----- ----- Ratio ----- =======================--==================================== Gasoline stoich 14.7 0.068 1 1 Gasoline Max power rich 12.5 0.08 1.176 0.8503 Gasoline Max power lean 13.23 0.0755 1.111 0.900 =======================--==================================== E85 stoich 9.765 0.10235 1 1 E85 Max power rich 6.975 0.1434 1.40 0.7143 E85 Max power lean 8.4687 0.118 1.153 0.8673 =======================--==================================== E100 stoich 9.0 0.111 1 1 E100 Max power rich 6.429 0.155 1.4 0.714 E100 Max power lean 7.8 0.128 1.15 0.870 =======================--====================================
Detail discussion of E85 tuning can be found at specialty E85 web forums such as www.e85forum.net/forum where they have assembled people with lots of first hand experience tuning with E85 in high performance situations.

E85 fuel ethanol content seasonal changes

E85 fuel blends change content seasonally just like all gasolines blends change with the seasons. This seasonal change in blend for E85 is primarily to improve cold weather starting, where the changes in gasoline during cold weather is to improve cold weather starting. In the summer months, gasoline must be blended to reduce vapor lock and to reduce evaporative emissions.

The recommended dates for changing E85 fuel blends are listed in a chart in the E85 handbook on page 22, which is in the "E85 Fuel Specification" tab.
The Volatility class specifications are broken down on page 10.

Volatility class 1 --- minimum ethanol 79%
Volatility class 2 --- minimum ethanol 74%
Volatility class 3 --- minimum ethanol 70%




As you can see each region has a different start date and recommendation for seasonal blends depending on local weather climate.

Here on the high plains east of the rockies in Colorado we run the class 1 fuel blend from mid June -- mid Sept, run class 2 fuel from mid Sept -- mid Oct and run the class 3 fuel blend from Mid Oct -- mid April, then back to the class 2 blend from mid April to mid June. The standard only specifies a minimum ethanol content, vendors can run higher ethanol content if it is economical. If it is cheaper for the fuel blender to add more he can. Ethanol content is bottom line driven by local weather conditions, and cold starting problems for local drivers just a gasoline blends are modified to give easier starting in cold weather.

In the Southern part of Texas they would never go to a class 3 blend, and in Wisconsin, they would only have the class 1 blend for about 2 months in the summer. In Florida they would be on class 1 almost all year long and in North Dakota and Wyoming and Montana, they would be on class 3 almost all year long.

Power available on E85

Many sources make a big deal about E85 having less thermal energy per gallon that a gallon of gas. They frequently draw the false conclusion that you cannot make more power on E85 than you can on gasoline. E85 actually has a higher specific energy at stoichiometric fuel air mixtures than gasoline, and at proper max power mixtures releases more thermal energy in the cylinder for a given amount of air to burn. Since an internal combustion engines power output is primarily air supply limited this means you can make 5% to nearly 30% more power on E85 than you can on gasoline.

(edit 6/10/08) Current experience shows turbocharged cars like the WRX and DSM families can run upwards of 30 psi boost on E85 tunes without knock. The only case I know of where knock was logged was on a 500+ whp DSM running 35-39 psi boost!

Ethanol specific energy at stoichiometric fuel air mixtures is actually higher than gasoline allowing a higher release of energy per lb of air burned than gasoline.

Typical gasoline Thermal energy 19,000 BTU/lb max power fuel air mixture 12.5:1
Typical E85 Thermal energy 13,475 BTU/lb max power fuel air mixture 6.975:1
Typical ethanol Thermal energy 12,500 BTU/lb 6.429:1

If you are consuming 100 lbs of air, lets see how much fuel energy you release for each of these fuels using gasoline as the base 100% reference.
100/12.5 = 8 lbs of gasoline @ 19,000 BTU/lb = 152,000 BTU = 100%
100/6.975 = 14.337 lbs of E85 @ 13,475 BTU/lb = 193,189.9 BTU = 127% more heat energy
100/6.429 = 15.555 lbs of Ethanol @ 12,500 BTU/lb = 194431.5 BTU = 128.9% more heat energy

Typical fuel energy contents:
gallon of gasoline = 125,000 Btu
1 gallon of ethanol = 84,400 Btu
1 gallon methanol = 62,800 Btu
1 gallon of gasohol
(10% ethanol, 90% gasoline) = 120,900 Btu
1 gallon of E-85
(85% ethanol, 15% gasoline) = 90,500 Btu
1 gallon of kerosene or light distillate oil = 135,000 Btu
1 gallon of middle distillate or diesel fuel oil = 138,690 Btu


My long term average on gasoline was 24 mpg, my mileage on the same setup on E85 was 22 mpg, my current mileage on gasoline is about 22 current mileage on E85 is 18 mpg.

Current setup upgraded turbo-
gasoline mileage 22 mpg = 5682 BTU/mi
E85 90,500 Btu /gallon / 18 mpg = 5028 BTU/mile (daily driving with periodic high boost acceleration)
E85 90,500 BTU/gallon/ 19.3 mpg = 4689 BTU/mile (driving mostly off boost as daily commuter)

Old setup stock turbo -
gasoline mileage Gasoline 125,000 Btu/ gallon / 24 = 5208 BTU/mile
My old setup, @ 92% of gasoline milage or 22 mpg
E85 90,500 BTU/gallon/22 = 4114 BTU/mile

A 5% increase in engine power is common on NA engines with minimal conversion changes, and much higher numbers are possible if compression or boost is used to take advantage of E85's higher fuel octane.

Last update 6/10/08)

Last edited by hotrod; 04-01-2011 at 11:51 PM.
hotrodView Public ProfileVisit hotrod's homepage!Find More Posts by hotrod


07-08-2005, 10:54 PM #3 hotrod
Scooby Specialist

Member#: 14141
Join Date: Jan 2002
Location: 13.239@102.85 @ 5800 ft on 13T
Vehicle:
2002 Impreza WRX
e85forum.net





Part 3

Testing ethanol content with the water test
The proper way to do the water test is specified on page 27 of the handbook.

Handbook method:

ethanol_guidebook.pdf

2.1 + 1.94 x (total vol - lower meniscus) = hydrocarbon
ethanol = 100 - hydrocarbon

Ethanol bonds very strongly with water so the percentage is not a direct relationship as seen above in the formula.
For example, If you add 10 ml of water to 100 ml of standard pump gasoline, and end up with 17ml of phase separation -- you have a full E10. (yes I know the math does not work but this is due to ethanol's bonding properties) In this case 10 ml of water and 10 ml of alcohol bond to form a mixture of 17 ml of water alcohol mix.


Choosing proper injector size for Subaru WRX E85 conversions

http://forums.nasioc.com/forums/show...1#post21693201

Simplified formula:

(turbo max air flow CFM at target boost) x 1.38 ~= static injector flow cc/min each injector on E85

(assumes a 4 cylinder engine with similar fuel needs to the Subaru WRX)

What is your test history to date (6/2005) with E85 ?

I just tallied up my usage over the last 2 years, (the first year I was very cautious and did not use very much). I've put about 500 gallons of E85 and 100% fuel grade ethanol through the cars tank --- that's some where around 40 fill ups, or around 9,000 miles or so on high ethanol (ie greater than 10%) blend fuels.


I am intentionally running the E85 with no special fuel system modifications. In a few years or when ever problems crop up, I'll pull things apart and see what has happened. So far I have absolutely no evidence of ANY kind of degradation on my 2002 WRX. The only non-stock component I'm running in the fuel system at the current time is a walbro 255 L/hr pump, so I cannot absolutely tell you how the stock pump likes the stuff.

Update ( Jan-Nov 2007)
I made a full conversion over the winter bringing the car back on the road with decapitated OEM injectors flow tested at 810 cc/min, an Aeromotive adjustable fuel pressure regulator which gives me the ability to dial in any fuel pressure I want from 35 psi to 70 psi with the turn of an allen wrench. A slightly improved ECUtek reflash, and the Mistubishi 16G turbo off a 96 Australian WRX. At 17 psi I produce 281 AWHP compared to 240 AWHP I was hitting on 100 octane Sunoco GT100 and 250 AWHP I could hit on Sunoco GT+ 104 octane race gasoline at higher boost pressures.

I have successfully tuned a usable home made FFV setup by optimizing the tune for a 50/50 blend of E85 and gasoline. At moderate boost levels the ECU is capable of making the necessary adjustments and open loop fueling is acceptable (see detail notes in the FFV segment below).

I have currently moved to a 100% E85 tune since I now have adequate availability of E85 and can run it all the time with little difficulty. In a cost per mile basis my current tune is equivalent to getting 30.5 mpg on pump premium (20mpg on E85 at $2.19 vs pump premium at $3.35/gallon). On a cost basis the car is consistently cheaper to drive on E85 than it is on gasoline.

Why is E85 a better fuel ?

Ethanol and is a very turbo friendly fuel for many reasons.
1. It has a much higher evaporative cooling power than gasoline so the intake air charge in the cylinder is significantly cooler that it is with a comparable mixture of gasoline --- that means higher VE.

2. Its octane as blended in E85 is about 100, its blending octane when added to gasoline is rated at 118, so it is a very cost effective octane booster.

3. Ethanol burns faster than gasoline but has a slightly longer ignition delay during the slow burn phase of combustion so the engine does not do as much negative work fighting rising cylinder pressures due to large ignition advances. The total ignition advance for E85 is almost identical to the ideal advance for gasoline so it does not cause the ECU problems when you mix them.

4. At proper mixture you actually are releasing more energy in the cylinder due to the higher quantity of fuel you can burn. ( Ethanol can burn effeciently at much richer mixtures than gasoline can) That means about a 5% increase in energy release all by itself.

5. Peak combustion pressures are actually lower for ethanol than for gasoline but the cylinder pressures stay higher longer, so you have more (longer) crank angle that is usable by the engine. This lower peak cylinder pressure also helps with detonaton control.

6. It will, at proper mixtures lower EGT's by around 200 deg F, but due to the higher quantity of exhaust gas products it produces you do not lose any spool up (in fact I would wager spool up is better).

7. It is much cheaper ( if you go to a station that is not trying to price gouge).

http://www.epa.gov/otaq/presentation...-isaf-no55.pdf


How much will my miles per gallon of fuel drop with E85?

The only negative to E85 is that it gives a lower fuel milage on a gallon for gallon basis to gasoline. The actual difference in energy content between straight gasoline and E85 is about 27%.

The drop in mileage is not as significant as you would think based on that difference due to the higher efficiency of the ethanol as a high performance fuel. This winter I was getting about 92% of the fuel milage I would get on gasoline on 100% E85.

The lower mileage is not really a big deal, ethanol has lower energy per gallon but your reduction in milage is not nearly as large as that difference would imply. Due to the higher torque,you use slightly smaller throttle openings to get the same level of performance, and due to the greater quantity of combustion products (more moles of gas) per lb of fuel the engine efficiency actually goes up slightly. My long term fuel mileage average is in the vicinity of 24.5 mpg, with pump gas, and with 75% ethanol blend, I was getting just over 23 mpg driven normally. Recently I have been flogging the crap out of the car to sort out new boost controller settings for my new turbo (went from a 13T to a 16G). Given I now have a larger turbo and all that is hardly a noticeable fuel mileage drop. I have gotten around 300 -345 miles/tank on straight gasoline when I was bone stock, and I expect to get from 280 - 310 miles per tank on the E-85 based on my notes of fuel consumption and accounting for the unusually hard driving I have been doing the last week working on the boost controller settings.

In very cold weather <20deg F I don't go above about 90% E85 to improve cold starting and speed up engine warm up a bit. Other than that the car loves E85 and so does my wallet ---- $1.89/gallon (6/2005) for 100 octane fuel is hard to argue with. It only drops my fuel mileage a small amount. I get 93.76% of my gasoline milage when driving conservatively in my WRX with the larger injectors and high ethanol fuel blends.


will a wide band O2 sensor accurately read fuel air mixtures with E85 blends ?

To get an accurate AFR reading you need to switch the meter to Lambda or equivalence ratio setting rather than AFR. Most O2 sensors assume you are running gasoline and will report a stoichiometric mixture as 14.7:1 which is the proper value for gasoline. E85 has a Stoichiometric mixture of between 9.7 - 10:1 and a max power mixture of about 6.98-8.5:1 or so, where with gasoline it is 12.5:1-to 13.1.

If you must use an O2 sensor that only reports gasoline AFR information simply divide the numbers it reports by 1.47 - 1.50.

On gasoline, my ECU is supposed to give a mixture of 11.5:1 and on 100% E85 the dyno's wide band reported an AFR of 11.6:1. That means that my true AFR on the E85 was about 7.8:1 which is right in the middle of max power mixtures for E85.




bmorecam is offline   Reply With Quote
Old 05-26-2011, 06:44 PM   #39
OOLIE

 
OOLIE's Avatar
 
Drives: 2011 LS
Join Date: Oct 2010
Location: FL
Posts: 1,644
wow that is some weekend reading LOL
__________________
OOLIE is offline   Reply With Quote
Old 05-26-2011, 06:46 PM   #40
KMPrenger


 
KMPrenger's Avatar
 
Drives: '10 ABM LT/RS, 06 Chevy Colorado
Join Date: May 2009
Location: Jefferson City, Missouri
Posts: 8,675
Well I scanned over that! lol. Nice info there...Thanks
__________________
Custom Magnaflow Exhaust, Vararam intake, MACE Ported Manifold, RX Ported TB, "Black Ice" manifold insulator, Elite Catch Can, ZL1 repro wheels, ZL1 Springs, DRL Harness, Front GM GFX, Heritage grill, Street Scene lower grill, NLP Spoiler, ZL1 rockers and much more!
KMPrenger is offline   Reply With Quote
Old 05-26-2011, 06:53 PM   #41
HopeRidesAlone

 
HopeRidesAlone's Avatar
 
Drives: 2010 Camaro Black 2SS/RS
Join Date: Mar 2010
Location: Maryland
Posts: 832
no sorry bmorecam im not i have injen and ark catback so cant help you with stock numbers
__________________
2010 Black 2LT/RS - Injen CAI, ARK DTS Catback Polished Tips, OBX LT Headers, Lowered on Eibach, 3/8 blackiceolator, Trifecta Tuned.- Totaled 3/10/13

2010 Black 2SS/RS - Feesler side skirt, Feesler Spoiler, Feesler carbon fiber bowties, H&R Lowering Springs.
HopeRidesAlone is offline   Reply With Quote
Old 05-26-2011, 07:00 PM   #42
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
Quote:
Originally Posted by HopeRidesAlone View Post
no sorry bmorecam im not i have injen and ark catback so cant help you with stock numbers
hey no worry.. I actually got info from a member here name "ronlslo" that used the same exact dyno as what I used and got some base numbers, but if you still need to have your car dynoed you could go along with me when I go sometime next week or two.
bmorecam is offline   Reply With Quote
Old 05-26-2011, 08:46 PM   #43
HopeRidesAlone

 
HopeRidesAlone's Avatar
 
Drives: 2010 Camaro Black 2SS/RS
Join Date: Mar 2010
Location: Maryland
Posts: 832
i would like to just to see what it puts out
__________________
2010 Black 2LT/RS - Injen CAI, ARK DTS Catback Polished Tips, OBX LT Headers, Lowered on Eibach, 3/8 blackiceolator, Trifecta Tuned.- Totaled 3/10/13

2010 Black 2SS/RS - Feesler side skirt, Feesler Spoiler, Feesler carbon fiber bowties, H&R Lowering Springs.
HopeRidesAlone is offline   Reply With Quote
Old 05-26-2011, 09:06 PM   #44
Rdditten
 
Rdditten's Avatar
 
Drives: 2010 ABM Camaro 2LT RS, STS TURBO
Join Date: Apr 2009
Location: Breckenridge, Michigan
Posts: 66
Send a message via AIM to Rdditten Send a message via Yahoo to Rdditten
Let me know how the e-85 works out. I have had this idea for quite some time. Asked around a bit and didn't get much positive feedback on it for our application. I am not sure that the V-6 fuel system can push enough e-85 for it to work?????
I do know this. I have a friend that drag races using e-85. He has a way to check the actual mix of the fuel. He has found that in the spring and fall it is not always true e-85. It is mixed differently at that time for starting ease. He finds that mid summer is best and is always sure to get a couple of drums to store for those times when he can't get good e-85. Just a little information for you in case you run in to this.
I like the idea of using e-85 with my turbo for the reasons you mentioned. Particularly the cooling effect with the high compression. Its unfortunate that Chevrolet didn't setup the Camaro from the start to use e-85.. That would have been great!
Good LUCK!

Last edited by Rdditten; 05-26-2011 at 09:07 PM. Reason: Missed a word
Rdditten is offline   Reply With Quote
Old 05-27-2011, 05:39 AM   #45
Rdditten
 
Rdditten's Avatar
 
Drives: 2010 ABM Camaro 2LT RS, STS TURBO
Join Date: Apr 2009
Location: Breckenridge, Michigan
Posts: 66
Send a message via AIM to Rdditten Send a message via Yahoo to Rdditten
http://www.raceone85.com/
Rdditten is offline   Reply With Quote
Old 05-27-2011, 07:52 AM   #46
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
fuel system was my main concern but vince at trifecta said that with our direct injection it will be possible. I am also fully aware of the winter and summer blend. We are in the summer range right now so I am not too worried about it. Plus if everything go good and depending how much extra hp I can get out of this conversion I am only planning to run it through the summer. We will all find out soon if our direct injection and high compression can benefit from e85. I be happy even if I can just get 5% extra hp with just tuning. Got my fingers crossed.
bmorecam is offline   Reply With Quote
Old 05-27-2011, 08:01 AM   #47
ROD1
Back to the hunt....
 
ROD1's Avatar
 
Drives: 2010 Camaro RS V6 #1301 DOB 3/23/09
Join Date: Aug 2009
Location: Ithaca NY
Posts: 2,561
Quote:
Originally Posted by bmorecam View Post
I guess one cant really take these numbers too seriously. It make sense that dyno is only good to figure out what we made and what we lost on the same dyno, same situation, same car.
Agreed. Every dyno is different and the numbers I posted were derived from an average of what seemed to be dialed in dynos.
ROD1 is offline   Reply With Quote
Old 05-27-2011, 09:10 AM   #48
PieNsky

 
PieNsky's Avatar
 
Drives: Victory Red 1LS
Join Date: Nov 2008
Location: Louisville,KY
Posts: 1,828
There is an E-85 station almost three miles from me.
PieNsky is offline   Reply With Quote
Old 05-27-2011, 10:36 AM   #49
bmorecam
Account Suspended
 
Drives: jealous vendors mad!! HAHA!!
Join Date: Jan 2011
Location: CYBERGMONSTER@GMAIL.COM
Posts: 3,660
I have one 7 miles from where I work and one about 15 miles from where I live so this work out pretty good for me too. Right now e85 in my area is little bit over $3.50 per gallon.
bmorecam is offline   Reply With Quote
Old 05-27-2011, 12:03 PM   #50
PoorMansCamaro



 
PoorMansCamaro's Avatar
 
Drives: Really Slow
Join Date: Apr 2010
Location: Las Vegas
Posts: 51,721
I think there are about 15-20 stations here in the las Vegas/Henderson areas. Lol
__________________
PoorMansCamaro is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Dyno Tune in Sacramento - Force Fed Performance LS3-376 Tuning / Diagnostics -- engine and transmission 3 03-19-2012 12:32 PM
$150 OFF 21st Century Muscle Cars DYNO TUNE 21STCENTURYMUSCLECARS V8 Bolt-Ons & Tunes 0 01-08-2011 09:57 AM
SCT or Dyno Tune jwjw12 Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 4 10-20-2010 02:28 PM
Trifecta tune or Dyno tune? cnjsanchez Camaro V6 LLT Engine, Exhaust, and Bolt-Ons 18 05-14-2010 11:42 AM
L99 A6 Dyno Results (ARH, Roto-Fab CAI,Borla, Tune) rinerracing6 Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 11 08-23-2009 05:09 PM


All times are GMT -5. The time now is 01:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.