Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Jason 98 TA
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons

Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons Bolt-Ons | Intakes | Exhaust

Reply
 
Thread Tools
Old 01-01-2012, 11:53 AM   #1
joey0480
 
Drives: 2013 Evo X
Join Date: Sep 2011
Location: New Jersey
Posts: 565
Troubleshooting with ADM washer bottle

hey all
Got the ADM race intake mounted up in the car. Fits well, top is snug and all. Figured I get to mounting the washer bottle. Maybe I am doing something wrong....but I measure out the 3 3/4 which leaves it mounted up straight against the strut tower and it is pushing the box so much that I would be unable to get the top mounted on because the screw holes don't line up.

This is the washer bottle that screws into the side of the ADM box.

Any suggestions or anyone run into this?
thanks
joey0480 is offline   Reply With Quote
Old 01-01-2012, 12:06 PM   #2
joey0480
 
Drives: 2013 Evo X
Join Date: Sep 2011
Location: New Jersey
Posts: 565
here are the pics...top pic without shows that the top fits flush and lines up.

Bottom with bottle is pushing the bottle too far forward to line up


joey0480 is offline   Reply With Quote
Old 01-01-2012, 02:36 PM   #3
bowtie98607
 
bowtie98607's Avatar
 
Drives: 12 SS2RS, 73 RS/TypeLT, 68 Vette
Join Date: Nov 2011
Location: Vancouver, Washington
Posts: 192
That is the same place I installed mine with no issues. I then put a vacuum fitting cover over the old air box mount stud to clean that up. Maybe I put the lid on first? I don't recall having any issues at all.
__________________
bowtie98607 is offline   Reply With Quote
Old 01-01-2012, 02:56 PM   #4
ADM PERFORMANCE

 
Drives: 2013 ZL1 #138
Join Date: Oct 2008
Location: DfW - Texas
Posts: 3,976
Answered.
ADM PERFORMANCE is offline   Reply With Quote
Old 01-02-2012, 01:07 PM   #5
joey0480
 
Drives: 2013 Evo X
Join Date: Sep 2011
Location: New Jersey
Posts: 565
thanks! got it. I put the bolt through the box, tightened the top of the box now, and slid the washer bottle on afterwards (thus putting the the pressure once the box is sealed).

thanks again
joey0480 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY - ADM Scoop & Apex Washer Tank Installed with a CAI intake ClutchKargo Camaro DIY & HOW-TO instructions & discussions 35 11-20-2014 09:53 AM
2010+ Camaro V6/V8 Roto-Fab Washer Reservoir Relocation Kit & ADM Performance Scoop! AutoAgenda V8 Bolt-Ons & Tunes 39 08-10-2012 02:41 PM
DELETE GMParts Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 0 12-25-2011 10:41 PM
ADM PERFORMANCE WASHER BOTTLE PICS ADM PERFORMANCE Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons 8 10-28-2011 09:16 PM
Adm scoop and Washer Bottle Rcfiddy1 Camaro DIY & HOW-TO instructions & discussions 1 10-26-2010 12:18 PM


All times are GMT -5. The time now is 03:14 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.