Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Hurst Shifters
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Specific Models / Packages > Camaro 1LE Forum

Camaro 1LE Forum Camaro 1LE Package releated discussions

Reply
 
Thread Tools
Old 01-31-2014, 07:42 PM   #1
GR8WHITE1
 
GR8WHITE1's Avatar
 
Drives: camaro
Join Date: Oct 2013
Location: ca
Posts: 190
1LE intake headers vmax tb dyno tune results.

Had Charlie at rpm motors tune my car today mods are stainless power headers with cats cai intake npp exhaust and vmax ported tb. Laid down 426hp and 416tq here's the graph.
Sent from my SPH-L710 using Tapatalk 2
GR8WHITE1 is online now   Reply With Quote
Old 01-31-2014, 08:25 PM   #2
shawn18
OWTATIME
 
shawn18's Avatar
 
Drives: CaRaMo
Join Date: May 2009
Location: North Carolina
Posts: 2,762
Nice!


Sent from my iPhone using Tapatalk
__________________
shawn18 is offline   Reply With Quote
Old 01-31-2014, 09:01 PM   #3
eagle1
 
eagle1's Avatar
 
Drives: 69rs/ss 2014 ss/rs 1le
Join Date: Oct 2013
Location: Albany Ga
Posts: 98
Got to feel good on the road now. Nice
__________________

69 rs/ss white
2014 ss/rs 1le hot red
eagle1 is offline   Reply With Quote
Old 01-31-2014, 09:24 PM   #4
VOGGS-LS3-1LE
Angry by Nature
 
VOGGS-LS3-1LE's Avatar
 
Drives: 13' Camaro 1SS/RS/1LE/NPP 1 of 76
Join Date: Aug 2013
Location: Pittsburgh, PA
Posts: 284
Headers and a CAI really benefit the ls3. Best results with a tune. Good job!
__________________

2013 CHEVROLET CAMARO 1SS/RS/1LE/NPP
1 OF 76
Roto Fab CAI
1LE BADGES
VOGGS-LS3-1LE is offline   Reply With Quote
Old 01-31-2014, 09:26 PM   #5
shawn18
OWTATIME
 
shawn18's Avatar
 
Drives: CaRaMo
Join Date: May 2009
Location: North Carolina
Posts: 2,762
Did you get a baseline pull before you did the install & tune?
__________________
shawn18 is offline   Reply With Quote
Old 01-31-2014, 10:11 PM   #6
GR8WHITE1
 
GR8WHITE1's Avatar
 
Drives: camaro
Join Date: Oct 2013
Location: ca
Posts: 190
Unfortunately not he's a bit of a ways away so just took it down after the install. Feels like she lost some torque down lower but pulls all the way up top and sounds like a monster with the npp exhaust. Have had a ton of thumbs up and people say it sounds awesome.

Sent from my SPH-L710 using Tapatalk 2
GR8WHITE1 is online now   Reply With Quote
Old 02-01-2014, 12:33 AM   #7
umiami2312
 
Drives: 2013 2SS/1LE Blue Ray Metallic
Join Date: Nov 2013
Location: Miami, FL
Posts: 98
this is the exact setup i will have installed in two weeks, i finally get my headers and tune! happy to see the numbers and glad that it still sounds good with the NPP. Just wondering, did you pull your fuse on the exhaust to keep the flaps open all the time? Video if possible?
umiami2312 is offline   Reply With Quote
Old 02-01-2014, 01:53 AM   #8
Msmall143

 
Msmall143's Avatar
 
Drives: Camaro
Join Date: Sep 2013
Location: NOVA
Posts: 1,732
It's really tough to determine gains without a pre install dyno run on the same dyno you did post install. But those are numbers you would expect which is great.

Here's an audio with similiar set up but pfadt headers, intake, tune. No ported tb



I did have a baseline done stock and after install of headers, cai (no scoop) and tune. the performance gain from pfadt headers, cai intake and tune was 43 rwhp. The stock baseline was done right before install, and the post install dyno was done same day immediately after install. Obviously on the same dyno...a Autodyn 30 Dynamometer. Just FYI....it was a 43 rwhp without air

Basically it was 43 rwhp. But I think it's fairer to say 38 rwhp.

I say this because we did 2 passes pre installs and the 4 passes post install. Apples to apples the second post dyno run showed a pick up of 38rwhp when compared to the second pre dyno run.

The gains continued to increase on the post install runs until the 4th and fifth pull which it then leveled out and became consistent at 43 rwhp gain when compared to the highest pre install run (second and last pre install pull)

I have the data points but am having issues plotting them because the software is giving me some issues

I've dynod as low as 376 and as high as 422 with this current setup, just shows how much these dynos vary
Msmall143 is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:02 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.