Magnaflow Exhaust 2010 Camaro

[NAHURRY]

^^ Yeh, I would love to hear that SGO..

[Striker]

Does anyone know if there are any down falls to removing the stock mufflers and just adding pipe extensions on a 2ss with less then 1,000 miles?

[JDP Motorsports]

Originally Posted by SGOS252382

I'm getting Kook's 1 7/8 headers, high flow cat mids, Magnaflow (#16579) 2.5 street catback put on my car next Thursday.
I'll try to post up a video soon after and report on how it sounds.

I ordered the Magnaflow street to help keep the noise level in check with long tubes. It should sound really good without being too obnoxious.

I'm going to have my car tuned in a couple weeks to turn off the AFM, but I'll report on how bad it is with my setup before I get the tune.

Any updates?? Can't wait to hear it!!!

Originally Posted by NAHURRY

^^ Yeh, I would love to hear that SGO..

Originally Posted by Striker

Does anyone know if there are any down falls to removing the stock mufflers and just adding pipe extensions on a 2ss with less then 1,000 miles?

Removing the mufflers and straight piping it won't hurt anything at all. It will give you a more aggressive sound.

Kind regards,

[JDP Motorsports]

I updated the first post to include the GFX Magnaflow Exhaust Systems 16481 and 16482. I also updated the pictures and added dyno info. If anyone has questions please feel free to call, email or PM me anytime!

I hope everyone has a great Thanksgiving!!!!!

Kind regards,

[NAHURRY]

Originally Posted by JDP Motorsports

I updated the first post to include the GFX Magnaflow Exhaust Systems 16481 and 16482. I also updated the pictures and added dyno info. If anyone has questions please feel free to call, email or PM me anytime!

I hope everyone has a great Thanksgiving!!!!!

Kind regards,

Thanks..and you have a good one also.

[JDP Motorsports]

Originally Posted by SGOS252382

I'm getting Kook's 1 7/8 headers, high flow cat mids, Magnaflow (#16579) 2.5 street catback put on my car next Thursday.
I'll try to post up a video soon after and report on how it sounds.

I ordered the Magnaflow street to help keep the noise level in check with long tubes. It should sound really good without being too obnoxious.

I'm going to have my car tuned in a couple weeks to turn off the AFM, but I'll report on how bad it is with my setup before I get the tune.

Sweet! That will be a very nice combination!!!! Keep us posted!

Kind regards,

[firengnred]

I'm considering tearing out the resonator and replacing with Magnaflow Tru-X and replacing stock cans with 4" Magnaflow rounds Part#14416 with 4" tips as cheaper alternative to cat back system. Opinions? This is an L99.

Superchips tune is all that's been done so far with AFM disabled. Will be Dyno'd tomorrow for comparison after the exhaust mods are complete

[toehead93]

I'm doing something similar. I am using Magnaflow #11386 thru-X muffler to replace the stock resonator, this is the same thru-X muffler on their Cat-Back systems. I'm going to keep the stock cans for a little while to see if I like, if not then I'll replace them with something. Just not sure what to replace the mufflers with. Have you confirmed the 14416 mufflers will fit?

I'm also adding LT headers. I'd like to find 4.5" double wall angle cut tips, having a hard time though.

[firengnred]

According to the guy at the shop, the 14416 mufflers will work. I was originaly considering just deleting the mufflers but he talked me out of it. He said the 14416 is a straight thru pipe and being only 4" would be almost as loud but give me better sound quality and maintain a little of the back pressure. How much of this is just him trying to make a few more dollars, i'm not sure. This is why i'm looking for opinions. Lot of knowledgable people on here who i'm sure can help me out.

Would like to consider LTH but here in Socialist Cali that would be a no-no since it "moves" the cats. I gotta get outta this State

[Iwantone2]

Originally Posted by firengnred

I'm considering tearing out the resonator and replacing with Magnaflow Tru-X and replacing stock cans with 4" Magnaflow rounds Part#14416 with 4" tips as cheaper alternative to cat back system. Opinions? This is an L99.

Superchips tune is all that's been done so far with AFM disabled. Will be Dyno'd tomorrow for comparison after the exhaust mods are complete

i have a similar set-up except my mufflers arent the rounds. x-pipe, 2.5" tubes, and magnaflows. sounds good and clean and no AFM drone (of course that doesnt apply to you though).

[toehead93]

The good thinkg about the thru-x muffler is you buy one part for $92 and you get an x-pipe and a muffler. Otherwise you're paying for the x-pipe and two mufflers. If you've done the muffler delete and add the tru-x muffler you'll have the same sound as the Magnaflow Competition Cat-Back. Although there may be drone, that's why I'm keeoing the stocks for now. Then I'll swa them for 4" rounds or the same used on the Street Cat-Back.

[firengnred]

Sound thinking there toehead93. You made me change my plans. Going with Comp axle back and Tru-X muffler

Saves me an additional 200 in parts

[firengnred]

Okay... so here's the dyno numbers from today. Again, 2SS/RS L99 A6, the only mods so far is a superchip tune with AFM disabled..........




My third pull was the best with 322 RWHP and 335 RWTQ

[JDP Motorsports]

Originally Posted by firengnred

I'm considering tearing out the resonator and replacing with Magnaflow Tru-X and replacing stock cans with 4" Magnaflow rounds Part#14416 with 4" tips as cheaper alternative to cat back system. Opinions? This is an L99.

Superchips tune is all that's been done so far with AFM disabled. Will be Dyno'd tomorrow for comparison after the exhaust mods are complete

The 14416's will fit and combined with the 11386 (Satin) or 14386 (Polished) it will have a more refined tone quality. We've had quite a few customers run this set-up. I think it sounds great!!!!

Originally Posted by toehead93

I'm doing something similar. I am using Magnaflow #11386 thru-X muffler to replace the stock resonator, this is the same thru-X muffler on their Cat-Back systems. I'm going to keep the stock cans for a little while to see if I like, if not then I'll replace them with something. Just not sure what to replace the mufflers with. Have you confirmed the 14416 mufflers will fit?

I'm also adding LT headers. I'd like to find 4.5" double wall angle cut tips, having a hard time though.

I would use the 14416's along with the 11386 if you're doing LT's, it will have a loud deep tone but it will be much more refined. We've got discounts on these products including free shipping. Please feel free to call, email or PM me with any questions.

Originally Posted by firengnred

According to the guy at the shop, the 14416 mufflers will work. I was originaly considering just deleting the mufflers but he talked me out of it. He said the 14416 is a straight thru pipe and being only 4" would be almost as loud but give me better sound quality and maintain a little of the back pressure. How much of this is just him trying to make a few more dollars, i'm not sure. This is why i'm looking for opinions. Lot of knowledgable people on here who i'm sure can help me out.

Would like to consider LTH but here in Socialist Cali that would be a no-no since it "moves" the cats. I gotta get outta this State

He sounds like an experienced guy offering good advise IMHO. It will take a lot of the harness out of the system. I moved out of SoCal in 2008 and I'm happy!

Originally Posted by firengnred

Sound thinking there toehead93. You made me change my plans. Going with Comp axle back and Tru-X muffler

Saves me an additional 200 in parts

If you haven't purchased your parts yet let me know! We've got some awesome deals going right now!!!

Kind regards,

[firengnred]

If you haven't purchased your parts yet let me know! We've got some awesome deals going right now!!!

All parts already ordered from you guys and installed. Sounds AWESOME!

[JDP Motorsports]

Originally Posted by firengnred

All parts already ordered from you guys and installed. Sounds AWESOME!

Nice!! I'm glad you're happy with the exhaust system!

Please feel free to call, email or PM me anytime with questions or for pricing on the other great products we offer. Have a great day and we appreciate your business!

Kind regards,

[caverman]

Originally Posted by firengnred

All parts already ordered from you guys and installed. Sounds AWESOME!

Ok....so tell us exactly what you put on. Do you have any sound clips?


Right now my plan on an LS3 is to add the #11386, remove the resonators, and do a muffler delete. That should basically be the same as the Comp Series and I'll have about $250 - $275 in the whole setup.

If that's to loud I'll add a couple #14416 to the system. Also...down the road I'll probably put on some LTs. I'll probably try it with that Comp Series type setup and if it's to loud I can add the #14416 mufflers.

Jordan....I'm sure I'll be calling you in a few weeks for the hookup.

[firengnred]

Ok....so tell us exactly what you put on. Do you have any sound clips?

I replaced the resonator with Magnaflow X-pipe muffler part #14379 and the stock cans with their Comp series axle back.

No sound clips yet. This weekend

[caverman]

Originally Posted by firengnred

I replaced the resonator with Magnaflow X-pipe muffler part #14379 and the stock cans with their Comp series axle back.

No sound clips yet. This weekend

Ok...still waiting on those sound clips. I'm assuming that you basically have straight pipes after the #14379. How do you like the sound?

[JDP Motorsports]

Originally Posted by firengnred

I replaced the resonator with Magnaflow X-pipe muffler part #14379 and the stock cans with their Comp series axle back.

No sound clips yet. This weekend

The 14379 isn't a resonated x-pipe, it's a 4x9x11" dual in/out muffler. The resonated x-pipe part #'s are 11386 (non-polished) or 14386 (polished) for the 4"x9"x14" used in the 2.5" comp series cat-back. It seems as though Don has made a mistake!!! I sent you a PM, please let me know if you have any questions!

Please feel free to call, email or PM me anytime with questions. Have a great day!

Kind regards,

[tiresmokindad]

Nice exhaust. Thanks for sharing your thoughts about it. I try to install that in my car. I think I can use it efficiently.