Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
ADM PERFORMANCE
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6)

V8 and V6 Transmissions / Driveline (6L80 / 6L50 / TR6060 / AY6) Driveshafts | Differentials | Gears | Rearends | Clutch | Shifters

Reply
 
Thread Tools
Old 11-09-2013, 06:18 PM   #1
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
remote clutch rezzy

Got mine on today, took like 20 minutes- super easy for the most part. I just called em up and they sent it on its way:
http://www.jdpmotorsports.com/manufa...o-zl1-jdpc1001

23k miles and this is what my brake/clutch fluid looked like:
Attached Images
 
Bo White is offline   Reply With Quote
Old 11-10-2013, 06:17 AM   #2
TheHorse13

 
TheHorse13's Avatar
 
Drives: 2011 Black SS M6
Join Date: Oct 2010
Location: Harpers Ferry, WV
Posts: 858
Given that we know that the fluid looks that way because of the clutch, and that the separate reservoir is much smaller, did you add a bleeder to the new clutch reservoir? My guess is that the fluid will look like that again and you will need a way to bleed it out.
TheHorse13 is offline   Reply With Quote
Old 11-10-2013, 07:44 AM   #3
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
The bleeder will be put in when I drop the tranny for a clutch. Just flush it through the stock bleed screw until then. Going to flush the brake fluid soon and get all that out of the system.
Bo White is offline   Reply With Quote
Old 11-10-2013, 11:10 AM   #4
HP_atTheWheels
 
HP_atTheWheels's Avatar
 
Drives: '10 2SS/RS Custom
Join Date: Oct 2012
Location: AZ
Posts: 222
Wow, thats some dirty fluid. I have been reading up on this and after seeing your fluid I'm am definately gonna do this soon. Can you feel a differance in the clutch?
HP_atTheWheels is offline   Reply With Quote
Old 11-10-2013, 01:09 PM   #5
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
Its always smoother engagement with fresh fluid. I could tell with my last car the G8 GXP.
Bo White is offline   Reply With Quote
Old 11-10-2013, 01:16 PM   #6
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
Took these just now:
Attached Images
  
Bo White is offline   Reply With Quote
Old 11-10-2013, 07:16 PM   #7
HP_atTheWheels
 
HP_atTheWheels's Avatar
 
Drives: '10 2SS/RS Custom
Join Date: Oct 2012
Location: AZ
Posts: 222
Sweet, thanks for the info and the pics.
HP_atTheWheels is offline   Reply With Quote
Old 11-11-2013, 03:50 PM   #8
TornadoSS
WICKDSS
 
TornadoSS's Avatar
 
Drives: 2011 1SS/RS IOM LS3
Join Date: May 2010
Location: Wichita, Kansas
Posts: 1,103
Quote:
Originally Posted by Bo White View Post
Took these just now:
Looks good Bo! I had my trans out to replace my clutch last week and installed the speed bleeder line. So much nicer to work with! Can't imagine doing without it now.
__________________
2011 IOM SS/RS, M6. Look up our all generation Camaro club website at Heartland Camaros
Gforce Engineering Drivetrain, ECS 1500 Supercharger, TSP Cam, Alky Controls Meth single nozzle. 91 octane, 698 RWHP 625 rwtq. 4200#+, Tuned by Justin "Justune" Kalwei
11.57 @ 126.8 mph with a crappy 1.80 60'.....still learning to drive....M&H DR's and skinnies on 17" Welds.
TornadoSS is offline   Reply With Quote
Old 11-11-2013, 04:10 PM   #9
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
Thanks, yes, looking forward to a clutch and bleeder upgrade.
One little trick I will share. When you start putting fluid back in for the clutch squeze the hose a few times until all the air comes out. This way the master didn't know anything happened. For me I filled the rezzy up and started squeezing the hose and the rezzy was almost empty by the time the bubbles stopped.
Bo White is offline   Reply With Quote
Old 11-11-2013, 04:15 PM   #10
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
Another thing the clamp that came with the kit for the master block off wasn't big enough to use for me. I will replace the one I used. That's just something I had on hand.
Bo White is offline   Reply With Quote
Old 11-11-2013, 04:22 PM   #11
BUSHMASTER
 
BUSHMASTER's Avatar
 
Drives: 2013 VR 2SS RS 1LE NPP
Join Date: Jan 2013
Location: SAN ANTONIO
Posts: 188
Where did you get the mounting bracket? I was going to install mine this weekend (bought a few months ago) but thought I had to drill holes to install. From your pic it looks like yours is mounted with a bracket.. Can you clarify foe me?
Thanks!
Bushmaster
BUSHMASTER is offline   Reply With Quote
Old 11-11-2013, 04:54 PM   #12
Bo White
Account Suspended
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 2,418
Mine came with the bracket already on the rezzy. Unscrew the front master rezzy screw and put it on.
Bo White is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.