Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Trunk Monkey Parts
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Engine | Drivetrain | Powertrain Technical Discussions > Camaro V8 LS3 / L99 Engine, Exhaust, and Bolt-Ons


Reply
 
Thread Tools
Old 06-24-2013, 05:48 PM   #1
Archaic2021
 
Drives: 2011 1ss
Join Date: Jan 2013
Location: birmingham, al
Posts: 112
What are you guys paying for cam installs.

I'm looking to cam my car and just wondering a general price. I'm hoping to do this as a gift for my birthday in August. I wish I could find someone in the southeast near Alabama that could do a cam install and tune it within a day or two.
__________________
2003 2500HD 6.0 4x4 -daily
2011 1ss LS3. Stainless power longtubes, slp blackwing intake, muffler delete, tune. 410Rwhp 405rwtq
Archaic2021 is offline   Reply With Quote
Old 06-24-2013, 05:54 PM   #2
Birm
 
Birm's Avatar
 
Drives: Florida Speed & Power
Join Date: Jan 2011
Location: Pinellas Park, FL
Posts: 3,188
http://www.camaro5.com/forums/showthread.php?t=274673

We are not that far. Good excuse to visit the beach for a few days
Birm is offline   Reply With Quote
Old 06-24-2013, 06:18 PM   #3
RogerBzSS
 
RogerBzSS's Avatar
 
Drives: 11 IBM n White 2SS/RS M6
Join Date: May 2011
Location: Tewksbury Ma
Posts: 354
I would be looking for shop hourly rates and expected time to do the install of the cam with supporting components springs hardened pushrods trunion upgrade etc.. and then the tune, different shops are more than likley different shop rates based off you're location..

you will also need to budget in the extras new oil and coolant probably a timing chain etc etc etc etc etc... as the list goes one the cost increases..

it all adds up, but you should do things once if you're going in to the internals..

my $0.02
__________________
Black CIA -Powder Coated Red Air Scoop - Vmax Ported Throttle Body - Ceramic Coated Dynatek Headers - High Flow Cats out thru factory Cat Back - JRE rough idle cam package - Trunion Upgrade - Valve Springs - Hardened Push rods - 3 bolt timing gear - SLP Under drive pully- Washer bottle relo kit - Hurst Short Throw Shifter with updated pin bushing from C5 member NH-SS - IdealG's improved Master Cylinder - GTO Clutch reservoir - L99 Brake Reservoir - Stainless Braided clutch line - wrapped up with a JRE Tune My SS layed down 462 hp on JRE's Superflow Dyno
RogerBzSS is offline   Reply With Quote
Old 06-24-2013, 06:34 PM   #4
Bo White


 
Bo White's Avatar
 
Drives: 2010 Summit White 1SS
Join Date: Feb 2012
Location: Vance Alabama
Posts: 5,030
Dave with the g8 gt in bham does swaps. I can help too. He's going to help me with mine this winter.
__________________
Retired wannabe
Bo White is offline   Reply With Quote
Old 06-24-2013, 06:42 PM   #5
Birm
 
Birm's Avatar
 
Drives: Florida Speed & Power
Join Date: Jan 2011
Location: Pinellas Park, FL
Posts: 3,188
Quote:
Originally Posted by RogerBzSS View Post
I would be looking for shop hourly rates and expected time to do the install of the cam with supporting components springs hardened pushrods trunion upgrade etc.. and then the tune, different shops are more than likley different shop rates based off you're location..

you will also need to budget in the extras new oil and coolant probably a timing chain etc etc etc etc etc... as the list goes one the cost increases..

it all adds up, but you should do things once if you're going in to the internals..

my $0.02
Please see the link I posted, has all FSP's install prices including Cam/Rods/Springs etc... broken down. If you find a shop that is willing to do an all inclusive deal then it is a win/win....Hence our Cam Install special
Birm is offline   Reply With Quote
Old 06-24-2013, 06:50 PM   #6
RogerBzSS
 
RogerBzSS's Avatar
 
Drives: 11 IBM n White 2SS/RS M6
Join Date: May 2011
Location: Tewksbury Ma
Posts: 354
Quote:
Originally Posted by Birm View Post
Please see the link I posted, has all FSP's install prices including Cam/Rods/Springs etc... broken down. If you find a shop that is willing to do an all inclusive deal then it is a win/win....Hence our Cam Install special
I did! good deal for the folks in you're area looking get the bump stick and supporting parts n pieces installed n tuned up
__________________
Black CIA -Powder Coated Red Air Scoop - Vmax Ported Throttle Body - Ceramic Coated Dynatek Headers - High Flow Cats out thru factory Cat Back - JRE rough idle cam package - Trunion Upgrade - Valve Springs - Hardened Push rods - 3 bolt timing gear - SLP Under drive pully- Washer bottle relo kit - Hurst Short Throw Shifter with updated pin bushing from C5 member NH-SS - IdealG's improved Master Cylinder - GTO Clutch reservoir - L99 Brake Reservoir - Stainless Braided clutch line - wrapped up with a JRE Tune My SS layed down 462 hp on JRE's Superflow Dyno
RogerBzSS is offline   Reply With Quote
Old 06-24-2013, 07:38 PM   #7
ZuluKilla8

 
ZuluKilla8's Avatar
 
Drives: 2010 Camaro 1SS/RS RJT
Join Date: Jan 2010
Location: NJ
Posts: 829
I would look at FSP, I dealt with Matt when he was up at ECS great guy to deal with.
__________________
2010 Camaro SS LS3 Holley Hi-Ram Manifold,Custom grind boost cam,Vortech V-3,10Rib 3.47 Pully Airfilter Pipe Delete, 10 PSI, TSP LT Headers, Flowmaster Outlaws, Alky Control Meth Kit, PFADT 1.25, ZL1 Fuel Pump, DSS 1000HP axles, Mantic ER2 Clutch, Full BMR rear suspension drag pack upgrade. C6 Vette 18 rims with M/T 305 out back. COPO Hood
Race Proven Motorsports tuned
ZuluKilla8 is offline   Reply With Quote
Old 06-24-2013, 08:11 PM   #8
BLACK10


 
BLACK10's Avatar
 
Drives: 2010 CAMARO. 10.04@133mph, 1.4 60'
Join Date: Jul 2009
Location: Lafayette, Louisiana
Posts: 4,585
Feel free to give us a call here at lethal racing. Remember, if the price is too cheap you want to question the brand/quality of parts being used. We use only name brand parts!
BLACK10 is offline   Reply With Quote
Old 06-24-2013, 08:17 PM   #9
MightymouseSS
 
Drives: 2011 LS3
Join Date: Jan 2012
Location: el paso tx
Posts: 544
I was quoted for 1500 cam install only no dyno or tune. This is in el paso tx so there's really no LS shops around here.
__________________
Vararam
Stainless Works Headers
Vmax TB
SLP loudmouth 2
Nightfury Cam
Mike Norris CC
Tuned by Southwest Speed
MightymouseSS is offline   Reply With Quote
Old 06-24-2013, 08:23 PM   #10
Bell040


 
Bell040's Avatar
 
Drives: 2SS/RS - Black - GFX
Join Date: Nov 2008
Location: B'ham, Alabama
Posts: 2,459
Quote:
Originally Posted by Bo White View Post
Dave with the g8 gt in bham does swaps. I can help too. He's going to help me with mine this winter.
Let me know if either of you need help or tools. I did mine in my garage a while back. I live in t-town, work in b'ham.
__________________
Ordered: 10-13-08
Built: 3-30-09 (#1691)
Recieved: 6-12-09

Blacked out, Cammed (Lunati Voodoo 233/245, .578/.598 @114°, +4°), ARH LTs, VR OTR CAI, Cutouts, and lots of other fun mods.
Bell040 is offline   Reply With Quote
Old 06-24-2013, 08:27 PM   #11
csjcsj


 
csjcsj's Avatar
 
Drives: 2010 Camaro SS/RS 6spd
Join Date: Sep 2009
Location: Jefferson, Ga
Posts: 4,400
Quote:
Originally Posted by Archaic2021 View Post
I'm looking to cam my car and just wondering a general price. I'm hoping to do this as a gift for my birthday in August. I wish I could find someone in the southeast near Alabama that could do a cam install and tune it within a day or two.
Roughly $2500+- depending in options! Try MTI! They are in Cobb Co in Ga, maybe a 2 or 3 hour drive, not sure! But that's the closest u know of!
__________________
csjcsj is offline   Reply With Quote
Old 06-24-2013, 08:40 PM   #12
HaubSS
 
HaubSS's Avatar
 
Drives: '11 IBM 2SS/RS LS3/M6
Join Date: Feb 2011
Location: Lemoore, CA
Posts: 467
My install and tune was $1,500. Turnaround for me was about 3 days IIRC. Good luck and find a good shop with a good tuner. DO NOT compromise or you will regret it. Do it once and do it right, might cost more upfront but will save you tons on the backside.
__________________
2011 IBM 2SS/RS - LS3/M6 - Grey Interior
Full bolt-ons + TSP 229/236, 112 LSA
Tuned by BROOKS PERFORMANCE
BMR Stage 3 suspension
MRR 288 - 20x10(+35), 20x11(+43)
HaubSS is offline   Reply With Quote
Old 06-24-2013, 09:02 PM   #13
GbrilliantQ
¡ʇuɐıןןıɹq
 
GbrilliantQ's Avatar
 
Drives: 2011 Camaro IOM 2SS/RS
Join Date: Dec 2010
Location: Decatur, Illinois
Posts: 2,598
Nothing . Tracy and RX really took care of me after my motor exploded. Since I got a new LS3 to replace my L99 he only charged me for the price of the custom cam and supporting parts.

From my Note
__________________
GbrilliantQ is offline   Reply With Quote
Old 06-24-2013, 09:07 PM   #14
Mydivorcegift
When is soon?
 
Mydivorcegift's Avatar
 
Drives: 2011, 2SS/RS, Synergy
Join Date: Aug 2012
Location: TN
Posts: 1,799
Quote:
Originally Posted by BLACK10 View Post
Feel free to give us a call here at lethal racing. Remember, if the price is too cheap you want to question the brand/quality of parts being used. We use only name brand parts!
This...

And honestly you don't want a cam swap and a tune done in a day or two.
__________________
Coming soon......
Mydivorcegift is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:46 AM.


Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.