Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com
 
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com > Technical Camaro Topics > Wheels and Tires Talk Sponsored by The Tire Rack

Wheels and Tires Talk Sponsored by The Tire Rack Discuss issues related to wheels and tires

Reply
 
Thread Tools
Old 07-23-2013, 01:30 PM   #1
Dyk-NO

 
Drives: 2010 Camaro LS M6
Join Date: Jun 2010
Location: Anchorage,Alaska
Posts: 915
Any 19" wheels on 305/315's

Contemplating about this setup so any pictures and comments would be very appreciated.
__________________
"From ZERO to a Tire-Burning HERO!"


Dyk-NO is offline   Reply With Quote
Old 07-23-2013, 05:51 PM   #2
Dyk-NO

 
Drives: 2010 Camaro LS M6
Join Date: Jun 2010
Location: Anchorage,Alaska
Posts: 915
bump^
__________________
"From ZERO to a Tire-Burning HERO!"


Dyk-NO is offline   Reply With Quote
Old 07-23-2013, 08:59 PM   #3
madmaxx18
 
madmaxx18's Avatar
 
Drives: 07_tundra/08_zo6
Join Date: Jun 2009
Location: Wichita falls, tx
Posts: 722
Check out my picture album
madmaxx18 is offline   Reply With Quote
Old 07-24-2013, 11:29 AM   #4
Dyk-NO

 
Drives: 2010 Camaro LS M6
Join Date: Jun 2010
Location: Anchorage,Alaska
Posts: 915
Nice! Are you running 300's up front too? How was it, Looks like it's sticking out
__________________
"From ZERO to a Tire-Burning HERO!"


Dyk-NO is offline   Reply With Quote
Old 07-25-2013, 01:22 AM   #5
Avalnch

 
Avalnch's Avatar
 
Drives: Rally Yellow Camaro+Avalanche
Join Date: Dec 2009
Location: Vancouver
Posts: 848
Check out my post here...
http://www.camaro5.com/forums/showpo...4&postcount=20

These are 19x11 Forgeline GA3R on all four corners with 315/30R19's. You'll need to run coilovers upfront with shortened springs if you want to fit the 315s up front and it'll stick out a tad.
__________________
C.A.I., ARH LT, Pypes Cat Back, ZL1 Shifter, Quantum Brake Ducts, JDP Tow Hook
Scorch Yellow Trim Kit, Shark Fin, AAC DRLs+ABLs+SMDs, ZTA Rear Spoiler, R.Y. 1LE Splitter
Pfadt coilovers, camber plates, trailing arms & differential bushings.
BMR adjustable toe-rods. Pedders ZL1 barz, rear cradle inserts, radius arm & steering rack bushings.
Hotchkis Max Chassis Brace (minus tunnel cross-over piece for SCCA rules)
1LE 3.91 gearzzz. Drive Shaft Shop Road Race Axle Upgrade. TurnOne power steering pump.
Forgeline GA3-R 19x11 + Hoosier R6 315/30R19
426 HP @ 5550 RPM / 427 TQ @ 4700 RPM
Avalnch is offline   Reply With Quote
Old 07-26-2013, 05:50 PM   #6
Dyk-NO

 
Drives: 2010 Camaro LS M6
Join Date: Jun 2010
Location: Anchorage,Alaska
Posts: 915
Well I'm only planning to run 300s on the rears I just wanted to see how it looks, I personally want to go as small as I can without making the wheel tire set up look too small. You get it. Well yea im trying to lower my car with my new set up so yea.
__________________
"From ZERO to a Tire-Burning HERO!"


Dyk-NO is offline   Reply With Quote
 
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:40 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.