Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums -
Go Back   Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - > Members List


iTrader Rating

iTrader Profile Recent Ratings
iTrader Rating:
Positive Feedback:
Members who left positive:
Members who left negative:
Total positive feedback: 9
View Complete Feedbacks for JANNETTYRACING
6 Months
12 Months
 Positive 0 0 0
 Neutral 0 0 0
 Negative 0 0 0

Visitor Messages

Showing Visitor Messages 1 to 10 of 80
  1. fireman1153
    07-22-2020 12:39 PM
    Do you offer any member or military discount codes for your website? I am looking to purchase your Metco Valve Cover Breather w/Check Valve for my 2010 Camaro. Thank you.
  2. Beto6.2
    05-08-2020 02:00 AM
    Currently have a 18 A10 Zl1 Camaro fbo and ethanol. Installing a stage 2 cam soon from either btr or vengeance racing or weaponx not sure yet. And also doing a 2650 blower would you recommend stock converter? Or upgrade converter?
  3. ALIALI10
  4. ALIALI10
  5. ALIALI10
  6. csmwilliamjohnson
    07-23-2019 11:21 AM
    Ted, I'm pretty new but I have been reading a lot of post and trying to figure out what I want to do with my 2018 Camaro SS 1LE. I have the performance CAI, and recently installed a ported TB. What tuner do you recommend and do you have a tune to maximize my current setup. I plan to put Kooks headers on but that will be another year. Any other recommendations would be greatly appreciated.
  7. JooktheSnooke
    09-25-2018 11:15 AM
    would this tune you give me be the only tune i need or would that only be to drive the car to be able to take it to a dyno? also if i dont tune the car right now, is it safe to drive the car as is and just bring it somewhere to get tuned? lastly would i have to buy the sct x4 device to upload this tune you send me? appreciate the help
  8. JooktheSnooke
    09-24-2018 08:55 AM
    how can i get a tune before i start the car? i would need someone to come to my house with a computer? also this might be a stupid question but when i was doing the work the engine block was drained of all its fluids. is there a bleeder on the block to remove the air and allow the new anti freeze to get into the block? i filled the radiator but i dont think the coolent is flowing
  9. JooktheSnooke
    09-24-2018 08:50 AM
    thank you for the reply. i found the issue thanks to help form the folks on here. i had the drivers side coil harness plugged in backwards. flipped it around and everything sounds nice.
  10. JooktheSnooke
    09-23-2018 03:11 AM
    hi Ted
    i was told to reach out to you
    did a cam install in my ls3. The cam is texas speed stage 2, 229/244 .629"/.615" . I also installed a new oil pump, timing chain and sprocket, lifters, push rods, valve springs, rockerarm trunion upgrade, heads cnc ported, spark plugs, and LT headers. When i went to start the motor for the first time, it was misfiring a lot through the exhaust. it sounds like gun shots. The check engine light came on with code P0300 (multiple cylinder misfire) after this happened, i removed all the spark plugs and found them to all be soiled except for cylinder # 1 & 5. I checked compression on all of the cylinders, they were all at 190 psi except for 1 &5, they were at 170 psi. after doing that i checked for spark on all coils, spark plugs, and spark plug wires. Fuel injectors were also good, because i made sure they all sprayed duing the cam install. I am not sure why this is happening. Any advice would be greatly appreciated

About Me

    YELLOW 2013 ZL1 AUTO
  • Signature
    Celebrating 34 years Performance parts, Installation, Fabrication, Dyno tuning, Remote custom tuning, and alignments. 203-753-7223 Waterbury CT. 06705


Total Posts
Visitor Messages
  • Wiki Contributions: 0
  • Last contributed Never
General Information
  • Last Activity: Yesterday 09:57 AM
  • Join Date: 06-26-2009
  • Referrals: 2


Showing Friends 1 to 10 of 151

All times are GMT -5. The time now is 07:00 AM.

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2020, vBulletin Solutions, Inc.