Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com

Camaro5 Chevy Camaro Forum / Camaro ZL1, SS and V6 Forums - Camaro5.com (https://www.camaro5.com/forums/index.php)
-   5th Gen Camaro SS LS LT General Discussions (https://www.camaro5.com/forums/forumdisplay.php?f=2)
-   -   MGW shifter (https://www.camaro5.com/forums/showthread.php?t=597242)

hudson773 09-12-2021 04:17 PM

MGW shifter
 
I ordered one about a month ago, still waiting:confused: they can't be making these shifters one at a time. why so long, anyone have a guess?

larry_g 09-12-2021 04:43 PM

Materials are scarce everywhere.

Sent from my Pixel 5 using Tapatalk

Shodown 09-12-2021 08:34 PM

They are made to order. Mine took about 3 weeks maybe a little longer.

hudson773 09-12-2021 09:02 PM

even if they are custom made, it doesn't take a month to make.at most a day.

SS_Dave 09-12-2021 09:37 PM

What did they say when you contacted them and asked?

hudson773 09-13-2021 09:02 AM

they said 3 to 4 weeks, and I wouldn't be charged until it is shipped. I am OK with all of that. I just don't understand why it takes a month. I would understand if they were flying off the shelves and they couldn't keep up with demand, but they are not. so why?

hudson773 09-15-2021 11:37 AM

it shipped:happyanim: I watched the install video a few times, any tips?

larry_g 09-15-2021 12:26 PM

The clips are PITA to release...even after watching the video a bunch of times.

hudson773 09-15-2021 01:02 PM

they look like a pain, I hope my fingers are still nimble enough

Fast.Freddie 09-15-2021 02:34 PM

make sure you do it on a lift.. I can't even imagine attempting it on the ground.. Killer upgrade though!

jethrobandit 09-15-2021 03:32 PM

Did mine on jack stands. Wasn't bad at all. I did have a transmission jack from Harbor Freight that made dropping it down a few inches much easier during that step. Seems involved, but one of the easier upgrades I've installed. The video does show every step and helps too.

EDIT: ALSO, go find you a good weighted ball. THAT will make a huge difference too.

Wizard1183 09-16-2021 05:59 AM

Quote:

Originally Posted by Fast.Freddie (Post 11071228)
make sure you do it on a lift.. I can't even imagine attempting it on the ground.. Killer upgrade though!

I did mine on the ground. Front end was on ramps. Floor jack beneath transmission to lower it a hair. I had to get a steel pipe to shift the transmission over to drivers side while my girlfriend connected the clip on passenger side. My hands were too big. Major PITA but much better than stick shift. Though it’s not as quiet with road noise. Spent about 3.5-4hrs total getting it done. Of course I wasn’t rushing? But it’s definitely work getting it installed. Best upgrade though other than my BMR rear trailing arms.

hudson773 09-16-2021 08:01 AM

1 Attachment(s)
Quote:

Originally Posted by Fast.Freddie (Post 11071228)
make sure you do it on a lift.. I can't even imagine attempting it on the ground.. Killer upgrade though!

I built these ramps just for this job. 9" lift should be plenty

Fast.Freddie 09-16-2021 10:31 AM

Quote:

Originally Posted by hudson773 (Post 11071536)
I built these ramps just for this job. 9" lift should be plenty

Good luck! As everyone says the clips are the toughest part. I am 250 LBS so anything on the ground is tough! :smiling1::smiling1:


All times are GMT -5. The time now is 02:26 PM.

Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.