My new obsession... ZL1
11-20-2016 After nearly 80,000 miles, 5 years, and a TON of mods/memories, I said "Good bye" to my 1st obsession, a'11 2LT/RS.... and "HELLO" to a '12 ZL1.... (only 20k miles on it)
http://i11.photobucket.com/albums/a1...psvq9hmuui.jpg http://i11.photobucket.com/albums/a1...ps766vzouv.jpg ..... This is the 1st time I've ever purchased a pre-owned vehicle from a dealership & not from a family member. I hope I did the right thing.... LET THE MODS BEGIN! But before the mods could begin, I had to drive it up to watch my son graduate Army basic training. (He was shocked to see the ZL1... it took him a minute to realize that it wasn't our old V6 :) ) http://i11.photobucket.com/albums/a1...ps7t00rqtj.jpg Performance / Engine Mods:
Cosmetic & Miscellaneous Mods:
Future Mods:
|
11-26-2016 Afterburner tail lights, sequential turn signal pigtails & concept side markers installed
http://i11.photobucket.com/albums/a1...psv9i1qs67.jpg 12-3-2016 Clutch Reservoir Relocation Kit installed Stock reservoir is shared between the brake & clutch.... http://i11.photobucket.com/albums/a1...psgpgu9q7g.jpg Removed dirty brake fluid from the reservoir; but no ALL of it. http://i11.photobucket.com/albums/a1...psfjtqsysa.jpg SLIGHTLY bent the bracket on the new brake reservoir to prevent the hose from rubbing against the body. http://i11.photobucket.com/albums/a1...psr9wz765z.jpg For some reason, getting the clamp seated properly was an absolute B**CH! (we ended up using a little WD-40 on the hose and it slid right into place. http://i11.photobucket.com/albums/a1...psqgdeuseh.jpg installed... http://i11.photobucket.com/albums/a1...psygxnurnb.jpg this shows where the hose would rub if the bracket wasn't slightly bent before installing.. http://i11.photobucket.com/albums/a1...psygxnurnb.jpg 12-3-2016 Tick Performance Remote Clutch SPEEDbleeder line install... pulled the lower panel off... http://i11.photobucket.com/albums/a1...ps9pxbnbdi.jpg getting a socket on the bleeder is tough... it's a tight fit, and if we dropped the socket, or the bleeder into the bell housing, we'd have to pull the tranny. :( http://i11.photobucket.com/albums/a1...pswnxl8zzo.jpg This is my buddy Greg... using the force, and praying... and probably peeing a little... while he attempted to remove the the old bleeder. (He did it on his SS, so we figured "No problem... YOU GOT THIS!") http://i11.photobucket.com/albums/a1...psg5ybm3bl.jpg There is an obvious difference between the '12 SS bleeder (top) and the '12 ZL1 bleeder (lower) http://i11.photobucket.com/albums/a1...psj5jiytrz.jpg ZL1 (left) SS (right) http://i11.photobucket.com/albums/a1...pseksmf4rh.jpg Fabricated a "ghetto bracket" and installed the speed bleeder. http://i11.photobucket.com/albums/a1...psttbgmtqp.jpg 12-3-2016 ZL1 Mild to Wild installed.. http://i11.photobucket.com/albums/a1...psuvfpibcb.jpg |
12-3-2016 Subwoofer, Kenwood DDX9903S & Pac-Audio Dash kit installed
Before.... http://i11.photobucket.com/albums/a1...psu4sp0u3f.jpg removed... http://i11.photobucket.com/albums/a1...psg4rc90lj.jpg Installed (with custom start up splash screen created and added) http://i11.photobucket.com/albums/a1...ps2nivvajk.jpg |
Love the PAC install - still debating if I want to go that way after doing the MyLink upgrade a couple of years ago -- looks awesome though!
-don |
Quote:
If you've recently upgraded to the MyLink system, my suggestion (for what it's worth) is to wait.... Sure, Android Auto / Apple Car Play and some of the other bells & whistles of an aftermarket head unit are great, but not if you just spent a large chunk of change to get the MyLink system retrofit. It's also worth mentioning that PAC is working on an updated version of the kit that addresses many customer concerns, and I'm sure will be well worth the wait. - Jay |
Awesome.
Great jobs with the mods. Well done. I'd love to see this "ghetto" bracket for the tick bleeder. Been thinking of doing this for a while. Congrats on the new"ish" ride. The ZL1 is a whole another beast. I went from a V6 2LT Camaro as well and it was night and day driving experience. |
Quote:
I have the old head unit still so I can do the setup with it when the updated PAC unit comes out! -Don |
Congrats to you and your son Jay. Build is looking great so far.
You got Bumblebee's big brother now ;) |
Quote:
here are a few pics of the bracket we made for the tick speedbleeder... I just ran out to the parking garage and snapped 'em with my phone. We just put heat shrink over a piece of metal, bent it to 90 degrees, put two holes in it for mounting, then used an extra clamp thing he had laying around the shop to hold the bleeder... http://i11.photobucket.com/albums/a1...psttbgmtqp.jpg http://i11.photobucket.com/albums/a1...psfd5kn4bt.jpg http://i11.photobucket.com/albums/a1...ps08zfvxqk.jpg Quote:
I was just about to supercharge the LLT when I realized it would be better for me to just drop that money as a down payment on a ZL1.... so now I have a supercharger, and a few more bells & whistles. ;) |
All times are GMT -5. The time now is 09:11 AM. |
Powered by vBulletin® Version 3.8.9 Beta 4
Copyright ©2000 - 2024, vBulletin Solutions, Inc.